Moneris SCRIBE 602 User manual

SCRIBE
602/612
PRINTERS
Quick Reference Guide
0011299
SCRIBE 612 PRINTER
HOW TO REPLACE PAPER ROLL
1. Unlock paper compartment cover by pushing
cover back from closed position (as indicated
by arrow) and lift cover to open (cover opens
on its rear hinge). If installing paper for first
time, go to step 4.
2. Cut or tear off any remaining part of existing
paper roll. Remove spindle from inside of
paper roll and set aside. Discard used roll.
3. Press “Feed/Copy” button to feed any
remaining paper through printer mechanism
and discard.
DO NOT pull paper through.
4. Unfasten end of new paper roll and tightly
fold over one corner on end to form a sharp
point (as shown in the picture at right).
5. Insert spindle into new paper roll and place
roll and spindle into paper roll compartment
with paper feeding from bottom.
6. Pull up lever on left side of print mechanism
and insert pointed end of paper roll into slot
at front of paper compartment until paper
appears through tear bar. Pull folded portion
of paper through until it clears tear bar.
7. Lower lever on side of print mechanism and
press “Feed/Copy” button to advance paper
through until about two inches of paper are
showing; tear off excess paper using tear bar.
8. Close paper compartment cover pushing
cover in reverse direction of arrows until
locking tabs on sides click into locked
position.
9. Perform a Printer Test (61+ENTER), if desired.
Push the paper compartment
cover in the direction
indicated by the arrow
to unlock it.
Control panel.
Paper
compartment
cover.
Power switch.
Tear bar.
Feed paper roll
end through this
slot as indicated
by arrows).
Locking tabs
for paper
compartment
cover.
Paper
compartment
cover.
Lift up lever
on left side
of print
mechanism.
Fold paper end
602
612
Your VISA Merchant Number is
Your MasterCard Merchant Number is

SCRIBE 602 PRINTER
Lift tab.
To insert
cartridge.
To remove
cartridge.
HOW TO REPLACE PAPER ROLL
When the “Paper Low” light on the printer is
lit, there is about 20% of the roll left. If a red
stripe appears on the paper, the roll should
be changed.
1. Remove paper compartment cover by
pressing centre rear portion of cover and
lifting up.
2. Remove any remaining paper by removing
roll and spindle and tearing paper using
tear bar on ribbon cover. Press FEED button
to feed remaining paper through printer
and discard.
3. Ensure end of new roll is straight, not
crumpled or folded and copies are same
length.
4. Insert spindle into new roll; place roll into
paper compartment with paper feeding from
bottom of roll, as shown in picture at right.
5. Feed end of paper roll into slot at inside
front of paper compartment; press FEED
button to feed paper through mechanism
until two inches of paper are showing;
tear off excess paper.
6. Replace cover by inserting cover bottom
under tear bar and snapping back into
place.
HOW TO REPLACE PRINTER RIBBON
1. Remove ribbon compartment cover by
pressing “lift” tab and lifting off.
2. Remove existing ribbon by first lifting left
edge of cartridge using tab provided, then
lifting right side out (as shown by the “up”
arrows in the picture at left); discard ribbon.
3. Turn tension knob on new ribbon clockwise
to remove any slack.
4. Lower right side of new ribbon into printer
so it engages the gear mechanism, then
snap left side into place (as shown by
the “down” arrows in the picture at left),
ensuring ribbon slides into ribbon slot.
5. Turn tension knob clockwise again to
remove any slack.
6. Replace cover by inserting tabs found just
above both sides of tear bar into slots next
to paper compartment cover and snapping
lift tab at bottom into place.
7. Feed paper approximately 2 inches to
ensure paper feeds properly; tear off
excess paper.
For Technical Assistance Contact
Merchant Customer Service
toll free 1-866-319-7450
or local Toronto and vicinity
416-234-7664
To download additional copies of this Quick Reference Guide
go to www.moneris.com/merchant/qrgui es
and open the PDF file scribe602/612qrg.pdf