Moneual G100 Series User manual

DESKTOP COMPUTER
USER GUIDE
Safety Notice:
It is intended for user safety and prevent any accidental damage.
Please read this safety notice carefully before using the product.
Version: 1.0
Applicable Models: G100 Series PC Case
Copyright ⓒ2010 MONEUAL Inc. All rights reserved. The MONEUAL, MONCASO, MiNEW, RYDIS, SONAMU
are trademarks, or registered trademarks of MONEUAL Inc. in the Republic of Korea and/or other counties.

Before reading this User Guide
Warning Icons
Notes
Before reading this User Guide, please note the following warning icons used in this Guide
Forbidden: The product could be damaged. Make sure to observe the
instruction.
Warning: The operator could be injured. Make sure to observe the
instruction.
Important: Key information, definition, general information or reference.
Some devices and software packages described in this Guide may be unavailable or
disagree depending on vendor’s specification. The contents of this Guide may not
match your computer environment.
The images and pictures used in this Guide including the cover sheet may not agree with
actual product.
No operation and technical service other than the Windows installed by default would be
provided.
Operation instructions and guidelines are subject to change depending on model.

4 G100 DESKTOP COMPUTER USER GUIDE
Product Specification
The product specification may disagree depending on the product model.
For further details, see the label attached to the mainframe of the product or the
vendor’s catalog.
* Product specification is subject to change, without prior notice, to improve
performance and functionality.
Dimension
Compatible Motherboards
Compatible Power Supply Units
Compatible Graphics Cards
5.25? Bay
3.5? Bay
Expansion Slots
Cooling Fan Hole
Front I/O Ports
ETC.
136(W) x 358(H) x 428(D)mm
micro-ATX
micro-ATX
Standard ATX
1 bays
1 bay (External), 2 bays (Internal)
4 slots
2 x 60mm (Rear)
3-in-1 card reader x1, Headphone x1, Mic x1, USB x2
Zero switch for 0W mode

G100 DESKTOP COMPUTER USER GUIDE 5
Safety Instructions 6
Components List 7
Front/Rear I/O ports and switches 8
How to assemble your computer 10
Table of Contents

6 G100 DESKTOP COMPUTER USER GUIDE
Safety Instructions
1. Carefully read this User Guide before you install the product.
2. Check the parts before you install the product and contact the distributor if there are any missing or
defective parts.
3. Before you install the product, wear gloves to prevent probable injuries due to internal parts or
peripherals of the case.
4. When installing the product or after completion of installation, do not put your hands into the product
while it is running.
Electric shock may be caused.
5. Exactly connect the pins and cables, referring to the manuals of the peripherals to be connected to
the product.
Incorrect wiring may cause damage to the product and its peripherals.
6. Do not block the air ventilation holes on the lateral sides and the rear side. Parts may be damaged
due to overheating of the product.
7. When using the product after finishing assembly, place the product on a flat and dry surface.
8. When using the product after finishing assembly, maintain a clearance of 20cm or more between the
product and the wall. Using the product in a narrow and poorly-ventilated place may cause damage
to the product due to overheating.
9. When using the product after finishing assembly, do not expose the product to fire, direct sunlight,
water, moisture, oil, etc.
10. The vendor is not responsible for any damage, failure and injuries caused by improper use of the
product.

G100 DESKTOP COMPUTER USER GUIDE 7
Components List
No.
1
2
3
4
5
6
7
8
9
10
11
8
22
9
4
1
1
1
Securing ODD
Securing Power supply, HDD,
Main-board and Expansion slot
Supporting Main-board
Isolation between bolt and
mainboard
Securing Fan
Mainboard speaker
Figure Q'ty Parts name / Uded for (English)
1
1
12 Cooling Fan
Optional parts
3Management Cable
Covering Expansion slot
Securing power supply bracket
Power supply bracket
Case supporter
0 or 4
Part List
Power Cord Quick Guide User Guide CD

8 G100 DESKTOP COMPUTER USER GUIDE
G-100
ODD
ON
OFF
G-100
ODD
Front/Rear I/O ports and switches
①
②
③
④
⑤
⑦
⑧
⑨
⑥
①Power saving button
Enter the power saving mode.
Press this button to eject the optical drive.
Press this button to open the front panel.
The stand-by power goes 0 W when you
turn off the switch after power off.
The data will be lost if you turn off the switch
before power off.
②Optical drive eject button
③Panel open button
④Power button
⑤Zero switch
⑥USB port
Connect USB peripherals
Connect earphone, headphone, etc.
Connect a mike for voice recording,
video chatting, etc.
Insert SD, SDHC or MMC card
⑦Headphone jack
⑧MIC jack
⑨3-in-1 card reader
It is recommended to use the USB ports on the rear
side to connect peripherals (external hard drive, etc.)
of power consumption 500 mA or more.
G100
(1) Front view

G100 DESKTOP COMPUTER USER GUIDE 9
Front/Rear I/O ports and switches
① ②
The power saving socket supports up to 1750 W.
If the power supported by the power strip is less
than 1750 W, connect electronic instruments within
the capacity supported by the power strip.
Power strip is sold separately
① Power saving socket ② Main power socket
Connect a power strip Connect the power cord of the mainframe.
G100
(2) Rear view

10 G100 DESKTOP COMPUTER USER GUIDE
How to assemble your computer
(1) Remove the side covers and the front panel (bezel)
(2) Motherboard installation
① Remove the 4 hand screws on the rear side
and then remove the two side covers.
Lay down the mainframe case on the floor as shown in the figure, check the mounting direction of the
motherboard and the case and mount the motherboard by aligning it to the setscrew positions. Tighten
the setscrews at each setscrew position.
(Caution: Pay attention not to drop the driver and tools on the motherboard while you are tightening
setscrews. This may cause damage to the motherboard.)
Check the setscrew positions
Side cover
② After removing the both side covers, widen
the hook on both sides of the bezel to
remove the bezel.
G100

G100 DESKTOP COMPUTER USER GUIDE 11
How to assemble your computer
① Check the graphic card slot on the motherboard.
(The slot specification is common to all vendors
but the shape of slot may look a little different
from vendor to vendor.)
② Thoroughly insert the graphic card as shown in
the figure.
③ Tighten the screws and adjust the bracket of the graphic card as shown in the figure.
Installation of the graphic card has been complete.
G100
(3) Graphic card installation

12 G100 DESKTOP COMPUTER USER GUIDE
2
2
(Back Side)
How to assemble your computer
G100
(4) HDD, ODD Installation
① As shown in the figure, mount the CD/DVD drive
and the hard disk on the drive bay rack and tighten
the setscrews.
② Install the drive bay rack with ODD and HDD installed and tighten the setscrews.
Tighten the setscrews.

G100 DESKTOP COMPUTER USER GUIDE 13
How to assemble your computer
G100
③ As shown in the figure, connect the power connector and data connector of the CD/DVD driver and the
hard disk.
Connect the CD/DVD drive connector (ODD)
Connect the hard disk connector (HDD)

14 G100 DESKTOP COMPUTER USER GUIDE
How to assemble your computer
G100
(5) Cable connection
1) Power saving module connection
2) ECO Board (ECO B/D) Connection
The motherboard and the power supply unit may be damaged if the pin and connector cables are
not exactly aligned.
Connect the cable after checking the wiring, referring to the manuals of the motherboard and the
power supply unit.
Connect the power connectors of the power saving module and the main power supply unit.
Since the connector port is shaped in a polygon as shown in the figure, it would not be connected in
a wrong direction.
Check the shape of the connector port and connect it exactly.
Connect the ECO board as shown in the figure, referring to the description of connector JUSB1/2 pin array
and cables (colors).
(Caution: Make sure to connect the cable after checking the - and + positions of each pin.
The motherboard may be damaged if the - and + positions are reversed.)
(※ The position and the direction of the connector may differ depending on product specification and vendor.)
Power saving module
Power supply unit
(Power saving module connector)
(Power supply connector)
ECO B/D connectorJUSB1/2
VCC(Red)
USB1-(Green) USB1+(White)
GND(Black)
1
2
9
10
GNDUSB1-
USB0- GND
VCC USB1+ USB0C
USB0+VCC

G100 DESKTOP COMPUTER USER GUIDE 15
How to assemble your computer
G100
3) Front USB Connection
4) Card Reader Connection
Connect the power connectors of the power saving module and the main power supply unit.
Since the connector port is shaped in a polygon as shown in the figure, it would not be connected in
a wrong direction.
Check the shape of the connector port and connect it exactly.
Connect the card reader as shown in the figure, referring to the description of connector JUSB1/JUSB2
pin array and cables (colors).
(Caution: Make sure to connect the cable after checking the - and + positions of each pin.
The motherboard may be damaged if the - and + positions are reversed.)
(※ The position and the direction of the connector may differ depending on product specification and vendor.)
Front USB connectorJUSB1/JUSB2
1
2
9
10
GNDUSB1-
USB0- GND
VCC USB1+ USB0C
USB0+ Key
(no pin)
VCC GNDUSB1-
VCC USB1+ USB0C
USB0+USB0-
VCC GND
GND
UD+
UD-
UV+
SD card reader(USB) connectorJUSB1/JUSB2
VCC1(Red)
USB0-(White) USB0+(Green)
GND(Black)
1
2
9
10
GNDUSB1-
USB0- GND
VCC USB1+ USB0C
USB0+VCC

16 G100 DESKTOP COMPUTER USER GUIDE
How to assemble your computer
G100
6) Front Audio Connection
7) Power PCB Connection
As shown in the figure, the audio connector would not be connected if the F_AUDIO pins are not
exactly aligned to the connector port.
Exactly install the connector by checking the pin array and the key (no pin) position.
Connect the power switch connector and the power LED connector to the positions shown in the figure
below.
(Caution: Make sure to connect the cable after checking the - and + positions of each pin.
The motherboard may be damaged if the - and + positions are reversed.)
(※ The position and the direction of the connector may differ depending on product specification and vendor.)
Front audio connector
Key(no pin)PRESENCE#
GND
MIC_JD LINE out_JD
LINE out_R
FRONT_JD
MIC_L
LINE out_L
F_AUDIO
1
2
9
10
Key(no pin)
PRESENCE#
MIC_R FRONT_JD
LINE out_L
GND MIC_JD
LINE out_JD
LINE out_R
MIC_L
MIC_R
Power SwitchPower LED
JFP1
1
2
9
10
Power
Switch
(Red)
Power
LED
Reset
Switch
HDD
LED
(White)
(Green)
(Black)

G100 DESKTOP COMPUTER USER GUIDE 17
How to assemble your computer
G100
Assemble the cables in the sequence order of the front panel removal in Page 10 (See P10).
① Mount the bezel while checking the position of hook.
② Mount the two side covers and tighten the four hand screws.
(6) Cable Connection

18 G100 DESKTOP COMPUTER USER GUIDE
Copyright ⓒ2010 Moneual Inc. All rights reserved. The MONEUAL, MONCASO, MiNEW, RYDIS, SONAMU are
trademarks, or registered trademarks of Moneual Inc. in the Republic of Korea and/or other countries.

Copyright ⓒ2010 Moneual Inc. All rights reserved. The MONEUAL, MONCASO, MiNEW, RYDIS, SONAMU are
trademarks, or registered trademarks of Moneual Inc. in the Republic of Korea and/or other countries.
Customer service: 1588-8178
Service hours
Weekdays: 09:00 ~ 18:00, Weekend: 09:00 ~ 12:00