Monogram Advantium ZSB9231NSS User manual

INSTALLATION
INSTRUCTIONS
Advantium® Built-In Wall Oven 240V 30”
MONOGRAM.COM
MFL59060933
Para consultar una version en español de este manual
de instrucciones, visite nuestro sitio de internet Monogram.com.

231-7000080 Rev. 2
Safety Information
CONTENTS
Design Information
Models Available...............................................2
Product Dimensions and Clearances................3
Tools and Parts Required .................................3
Advance Planning .............................................3
Installation Preparation
Electrical Requirements ....................................4
Install Junction Box ...........................................4
Preparing the Opening (Installation without
an accessory storage drawer)........................5
Flush Mount ......................................................7
With Accessory Storage Drawer.......................8
Installation Instructions
Step 1, Remove Packaging and Parts..............9
Step 2, Route Conduit.....................................10
Step 3, Install Bottom Trim..............................11
Step 4, Install Mounting Screws......................11
Step 5, Finalize Installation.............................11
MODELS AVAILABLE
ZSB9231NSS – Stainless Steel
ZSB9232NSS – Stainless Steel
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
IMPORTANT —Save these instructions
for local inspector’s use.
IMPORTANT —Observe all governing codes and
ordinances.
•Note to Installer —Be sure to leave these
instructions with the Consumer.
•Note to Consumer —Keep these instructions
with your Owner’s Manual for future reference.
•Skill Level — Installation of this appliance
requires basic mechanical and electrical skills.
• Completion Time —1 Hour.
• Proper installation is the responsibility
of the installer. Product failure due to improper
installation is not covered under the warranty.
See Owner’s Manual for warranty information.
IMPORTANT —Use this oven only for its
intended purpose. Never use the oven for warming or
heating a room. Prolonged use of the oven without
proper ventilation can be hazardous.
CAUTION For personal safety, remove
house fuse or oven circuit breaker before beginning
installation to avoid severe or fatal shock injury.
CAUTION For personal safety, the
mounting surface must be capable of supporting the
cabinet load, in addition to the added weight of the
oven and drawer, plus additional oven loads.

31-7000080 Rev.2 3
Design Information
PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model.
TOOLS AND PARTS REQUIRED
(NOT SUPPLIED)
•#2 Phillips screwdriver
•Hand held drill
•High speed drill bit, 3/32" diameter
•3/8" slot head screwdriver
•Level
•Saw
•2x4 or 2x2 lumber for installing runners
or 3/8" plywood for floor (if required)
•Wood screws or other hardware for installing runner or
shelf to support oven (if required)
•Safety glasses or goggles
ELECTRICAL TOOLS AND PARTS
REQUIRED (NOT SUPPLIED)
•Junction box
•Electrical cable (3-conductor or 4-conductor wire as
required by local codes)
•UL-listed conduit connectors
•Wire cutters and wire strippers
ADVANCE PLANNING
•These ovens may be installed directly into a 30”
wide oven cabinet.
•Cutout dimensions are NOT the same for
installation with or without an accessory storage
drawer. Make sure to use the correct cutout when
preparing the opening.
IMPORTANT— This oven is not
approved for use above another built-in Advantium
Speedcook oven, a side by side installation or below
a countertop.
•For personal safety, this oven cannot be installed
in a cabinet arrangement such as an island or
peninsula.
• The oven must be installed at least 36-3/4” above
the floor.
• Allow for clearance to adjacent corners, walls,
drawers, etc.
• Cabinets installed adjacent to wall ovens must have
an adhesion spec of at least 194ºF temperature rating.
The oven must be securely installed in a cabinet that
is firmly attached to the house structure. Weight on
the oven door could cause the oven
to tip and result in injury. Never allow anyone to
climb, sit, stand or hang on the oven door.
If installing the drawer accessory, the drawer must
be assembled to the oven prior to installation into
the cabinet. See the Accessory Storage Drawer
Assembly Instructions.
FLUSH MOUNT INSTALLATION
This installation method allows for the unit face to be
inline with the cabinet face.
IMPORTANT: HIGH SKILL LEVEL IN CARPENTRY
IS REQUIRED. Non-standard cabinetry may be
required.
Flush installation of the oven will lead to the exposure
of the cabinet face frame edges.
Side cleats may be visible and should be a finished
surface.
Model Door Depth
ZSB9231NSS 1-3/8”
ZSB9232NSS 1-7/16”
20-1/4”
29-3/4”
21-1/2Ǝ
1Ǝ
13 1/4Ǝ
2-1/4Ǝ
Door Depth
See table
below

431-7000080 Rev. 2
Installation Preparation
INSTALL JUNCTION BOX
The conduit is located at the top right on the back of the
oven.
Locate and install the junction box within reach of the
oven conduit.
•Through the left or right sides of the cabinet wall
and into adjacent cabinet.
•Or, through the cutout floor.
•Or, in the upper cabinet.
Cutout
Height
ELECTRICAL REQUIREMENTS
Single Advantium Installation
Product rating is 120/208 or 120/240 volt, 60 Hz,
30 amps. This product must be connected to a supply
circuit of the proper voltage and frequency and protected
by a time delay fuse or circuit breaker. Power should be
supplied from a separate, dedicated 30-ampere branch
circuit. Wire size must conform to the requirements of the
National Electrical Code or the prevailing local code.
Combined Advantium and Wall Oven Installation
When installed in combination with a single wall oven, use
separate electrical junction boxes.
Refer to single oven installation instructions for electrical
requirements of that product.
These connections must be made by a qualified
electrician. All electrical connections must meet National
Electrical Code or prevailing local codes.
Combined Advantium and Warming Drawer
Installation
When installing the Advantium oven over an electric
warming drawer, a separate 120V, 60Hz, properly
grounded receptacle must be installed. See instructions
packed with the warming drawer.
WARNING
• The electrical power to the oven branch circuit must
be shut off while line connections are being made.
• Use copper wiring only.
• Electrical ground is required on this appliance. The
free end of the green wire (ground wire) must be
connected to a suitable ground. This wire must remain
grounded to the oven.
• If cold water pipe is interrupted by plastic,
non-metallic gaskets, union connections or other
insulating materials, DO NOT use for grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the NEUTRAL or
GROUNDING circuit. A fuse in the NEUTRAL or
GROUNDING circuit could result in an electrical shock.
• Check with a qualified electrician if you are in doubt
as to whether the appliance is properly grounded.
Failure to follow these instructions could result in
serious injury or death.
GROUNDING INSTRUCTIONS
WARNING Improper use of the grounding plug can result in a risk of electric shock.
This appliance must be connected to a grounded, metallic, permanent wiring system, or an equipment
grounding conductor should be run with the circuit conductors and connected to the equipment grounding
terminal or lead on the appliance.

31-7000080 Rev.2 5
Standard Installation Preparation
PREPARE THE OPENING
The Advantium 240V can be installed in combination
with other Monogram Built-In appliances. Always
follow each product’s Installation Instructions to
complete the installation.
Single Advantium 240V Installation:
Order a 30” wide single oven cabinet or cut the
opening in a wall to the dimensions shown.
30” 23-1/2”
25-1/4”
17-1/2”
Construct
Base
Min. 3/8”
Plywood
Supported
by 2x4
or 2x2
Runners all
Four Sides
36-3/4”
Min.
• Always maintain 36-3/4” minimum height from the floor
to the cutout in any single or combined installation.
• Allow the following clearances around the cutout on the
IURQWVXUIDFHRIWKHFDELQHWí´IURPWKHWRSí´
IURPWKHVLGHHGJHVDQGí´IURPWKHERWWRP1RWH
these refer to minimum clearances required for installation
and do not reflect actual product dimensions.)
• Oven overlaps will conceal cut edges on all sides of
the opening.
When installed over a single oven or a warming
drawer, allow at least 2” between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 240V and the other
appliance overlaps.
Construct a solid oven floor of 3/8” min. thick plywood
supported by 2 x 4 or 2 x 2 runners on all sides.
• The support must be level and rigidly mounted, flush
with the bottom edge of the cutout.
PREPARE THE OPENING (CONT.)
Installation over a Warming Drawer:
30” 23-1/2”
25-1/4”
17-1/2”
36-3/4”
Min.
2” Min.
(3”
recommended)
Per warming
drawer
requirement
Construct
Solid Bottom
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven supports
above the Warming Drawer location do not obstruct
the required interior depth and height. See Warming
Drawer installation instructions for details.
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined
installation.

631-7000080 Rev. 2
Standard Installation Preparation
PREPARE THE OPENING (CONT.)
Installation over a Wall Oven and
Warming Drawer: Construct
Solid Bottom
Min. 3/8”
Plywood
Supported
by
2x4 or 2x2
Runners all
Four Sides
30” 23-1/2”
25-1/4”
17-1/2”
2” Min.
Per Oven
Requirement
45-1/4”
Min.
Per warming drawer requirement
2” Min.
(3” recommended)
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven supports
above the Warming Drawer location do not obstruct
the required interior depth and height. See Warming
Drawer installation instructions for details.
CAUTION
For personal safety, the mounting
surface must be capable of supporting the cabinet
load, in addition to the added weight of the oven and
drawer, plus additional oven loads.
PREPARE THE OPENING (CONT.)
Installation over a Wall Oven:
30” 23-1/2”
25-1/4”
17-1/2” 2” Min.
(3” recommended)
45-1/4”
Min.
Construct
Solid Bottom
Min. 3/8”
Plywood
Supported by
2x4 or 2x2
Runners all
Four Sides
Per Oven
Requirement
• If you are replacing an electric double oven with the
combined installation of an Advantium 240V and a
single oven, use the dimensions shown. The middle
rail separating the two openings may need to be
larger than the 2” minimum shown.
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined
installation.

31-7000080 Rev.2 7
Flush Mount Installation Preparation
PREPARE THE INTERIOR
Cut and install side cleats:
• Cut side wood cleats to height of cabinet opening
and approx. 2-1/2” in depth. Install, on each side,
Dim. E (See table below) from the front face of the
cabinet.
Cut and install bottom cleat:
• Cut bottom wood cleat to a height of 1-1/8”, a depth
of the cabinet minus Dim. E (See table below) and
a width of 25-1/4” to fit between side cleats. Install
onto the cabinet floor between the side cleats, push
it all the way back against cabinet wall and make
sure its front face aligns with the front faces of the
side cleats (Dim. E, from the table below, gap from
the front cabinet face).
E
C
B
D
AA
A Side and top cleats depth 2-1/2” min.
B Bottom cleat height 1-1/8”
C Bottom cleat depth Cabinet depth minus Dim E.”
D Bottom cleat width 25-1/4”
E All four cleats inset depth ZSB9231NSS: 1-3/8”
ZSB9232NSS: 1-7/16”
TOP
VIEW
Front Face of Cabinet
EE
A A
C
D
PREPARE THE OPENING
The Advantium Built-In Oven can be installed
in combination with other Monogram Built-In
ovens. Always follow each product’s Installation
Instructions to complete the installation.
Single Advantium Built-In Oven
Installation:
Cut the opening in a cabinet to the dimensions
shown.
**20 1/2”
Construct
solid bottom
- Min. 3/8”
plywood
supported on
all four sides.
Must be able to
support weight
of oven and
contents.
36-3/4”
Min.
F *
23-1/2” min.
• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
Approved Flush Installation Dimension F
1/8” Reveal 1/4” Reveal
Single Advantium 30” 30-1/4”
Over Warming Drawer 30” 30-1/4”
Over Oven 30” 30-1/4”
Over Oven and Warming Drawer 30” 30-1/4”
** Top and bottom reveals are set to 1/8”.
2” min.
(3” recommended)
Per appliance
specs.
Oven or
warming drawer

831-7000080 Rev. 2
Installation Preparation with Accessory Storage Drawer
PREPARE THE OPENING (cont.)
The Advantium Built-In Oven can be installed in combination with other Monogram appliances. Always follow each
product’s Installation Instructions to complete the installation.
Single Advantium Built-In Oven Installation:
Order a 30Ǝwide single oven cabinet or cut the opening in a wall to the dimensions shown.
Dimension 1/8”
Reveal 1/4” Reveal
K 30” 30-1/4”
Preparation with an Accessory Storage Drawer
As needed, see the Standard Mount Installation Preparation OR Flush Mount Installation Preparation for
configuration details. Note the modified cutout height below.
30Ǝ23-1/2Ǝ
25-1/4Ǝ
Min.
21Ǝ
36-3/4Ǝ
Min.
Construct
solid bottom - Min.
3/8” plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.
STANDARD MOUNT: 23-1/2Ǝ
K*
23-5/8Ǝ
36-3/4Ǝ
Min.
Construct
solid bottom - Min.
3/8” plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.
FLUSH MOUNT:
• For flush installation, make the bottom cleat height 3/4” when installed over a storage drawer.
$OORZWKHIROORZLQJFOHDUDQFHVDURXQGWKHFXWRXWRQWKHIURQWVXUIDFHRIWKHFDELQHWí´IURPWKHWRSí´
from the side edges, and 3/4” from the bottom. (Note: these refer to minimum clearances required for installation
and do not reflect actual product dimensions.)
• Oven overlaps will conceal cut edges on all sides of the opening.
• When installed over a single oven or a warming drawer, allow at least 2Ǝbetween the two openings. This
separation will provide clearance for bottom overlap of the Advantium Built-In Oven and the other appliance
overlaps.
• The support must be level and rigidly mounted, flush with the bottom edge of the cutout.

31-7000080 Rev.2 9
Installation Instructions
1
REMOVE THE PACKAGING AND PARTS
• Remove all packing material and tape.
• Locate parts package containing mounting
screws.
• Remove the oven from the carton. Do not lift unit
by handle or conduit. Two people are required to
lift this oven.
• Open the door and remove any packaging in
oven.
Owner’s
Manual
Owner’s Manual Installation
Instructions
Glass Tray
Metal Grill Tray
Turntable Ring
Rack
Cooking Guide
Cooking
Guide
Metal Tray
Bottom Trim
IMPORTANT:If installing the Advantium Built-In
Oven with an accessory storage drawer, read the
storage drawer assembly instructions to assemble
the products together before proceeding to Step 2.
5 Color-Matched Screws
(4 required, 1 extra) 8 Brass Screws for the
Bottom Trim
(3 required, 5 extra)
Flat-Head Screws (4 extra)

10 31-7000080 Rev. 2
Installation Instructions
2
ROUTE CONDUIT THROUGH
CUTOUT
CAUTION Two people are required to lift
the oven into the opening.
Grasp the bottom at front and rear. Discard foam
base. DO NOT USE HANDLE OR CONDUIT TO
LIFT THE OVEN. DAMAGE WILL OCCUR.
With oven in front of the cabinet opening:
•Insert conduit into cabinet opening. Connect oven
wiring and branch circuit.
•Lift the oven into the opening while continuing to feed
the conduit in the direction of the installed junction
box. Be sure the conduit does not get pinched
between the back of the oven and the cabinet wall.
•Leave oven a few inches forward of the cabinet
front frame. Do not push the unit all of the way into
the cutout.
(Oven shown without
accessory storage drawer.)
WARNING
•Disconnect power to the junction box before
making the electrical connection.
•Electrical ground is required on this appliance.
•Do not connect the electrical supply until appliance
is permanently grounded.
2
ROUTE CONDUIT THROUGH
CUTOUT (CONT.)
When connecting to a 3-conductor branch
circuit:
•Connect oven red lead to branch circuit red lead.
•Connect oven black lead to branch circuit black lead.
•Connect oven green ground lead and white lead
to branch circuit neutral (white or gray).
When connecting to a 4-conductor branch
circuit:
•Connect oven red lead to branch circuit red lead.
•Connect oven black lead to branch circuit black lead.
•Break connection between oven white lead and
oven green ground lead.
•Connect oven white lead to branch circuit neutral
lead (white or gray).
•Connect oven green ground lead to branch circuit
ground lead (green or bare copper).