Monogram ZIC360NHRH User manual

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
SECTION 1
SECTION 2
1/4" FRAMED PANELS 3/4" OVERLAY PANELS
FLUSH INSET INSTALLATION
STANDARD INSTALLATION

OVERALL DIMENSIONS
AFTER PANEL INSTALL
ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
† Dimensions include 3/4" custom cabinet panel
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
FLUSH INSET INSTALLATION
SPECIFICATIONS
Overall Width 38" (96.5 cm)†
Overall Height 84 1/2" (214.6 cm)†
Overall Depth 26" (66.0 cm)†
Door Clearance 38 3/4" (98.4 cm)
Cutout Width 39" (99.1 cm)
Cutout Height 85" (215.9 cm)
Cutout Depth 26 3/16" (66.5 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 640 lb (290.3 kg)
38" (96.5)
11 1/2"
(29.2)
20 5/8" (52.4)
26" (66.0)
* 84 1/2"
(214.6)
*73"
(185.4)
*26 7/16"
(67.1)
*4"
(10.2) *4" (10.2) SIDE VIEWFRONT VIEW
* 83 1/2"
(212.1)
35" (89.0)
Case width
38 3/4"
(98.4)
TOP VIEW
ZIC360NHRH
Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
Allow 15" (38.1) min
clearance for 115˚
door swing
* Shipping height. Use leveling legs and wheels for maximum 1" height
adjustment from shipping height. Nominal installation height is 84”

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
AMounting the junction box in this
location will also allow for front
accessibility through access panel.
BWater supply area.
WARNING:
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
The information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
The information below applies to all
installation constructions:
• A wall bracket, bolts and toggles will
be supplied with the unit.
• The bolts will be used to attach bracket
to wall in 4 locations. Two of the
locations must penetrate the center of
the wall studs.
• The toggles are used for stability in
drywall and when metal studs are
encountered. Lag bolts are used in
wood studs.
• In installation opening, measure 82"
from floor and draw a horizontal line.
• Locate and mark the wall studs on
horizontal line. Verify at least two studs
have their centerlines within the center
32.5" of installation opening to ensure
2 wall studs are penetrated.
• The bracket will be centered left to
right in opening with bottom of bracket
on the horizontal line.
• When unit is placed in opening, the
bracket tabs will align with openings
in back of the unit. The unit will be
secured to the bracket using supplied
“L” bolts.
See Installation Instructions for
detailed instructions.
FLUSH INSTALLATION
ZIC360NHLH_RH
39" (99.1) Flush inset width
37 1/2" (95.3)
Width between cleats
3/4" (1.9)
Width of side cleats
5 1/4" (13.3)
1/2" (1.3)
26 3/16" (66.5)
Flush inset depth
20 15/16" (53.2)
Depth to cleat
FRONT VIEWSIDE VIEW
TOP VIEW
3 1/2"
(8.9)
W
Finished cleats
Finished cleats
Case Trim
3/4" Panel
Case
Door
6"
(15.2)
24 3/16"
(61.4)
7"
(17.8)
7"
(17.8)
10"
(25.4)
3 1/2"
(8.9)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
84"
(213.4)
height
to cleat
85"
(215.9)
WATER
3 1/2"
(9.0)
NOTES
FLUSH INSET INSTALLATION 3/4" PANELS FLUSH INSET INSTALLATION
A
B
ANTI-TIP BRACKET
24" (61.0)
1 1/2"
(3.8)
3"
(7.6)
7/16" (1.1)
Trim overlap
35 1/2" (90.2)
2 5/16"
(5.9)
SIDE VIEWFRONT VIEW
ZIC360NXRH
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC. 6"
(15.2)
10"
(25.4)
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
81 1/2"
(207.0)
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0)
WATER
10" (25.4)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
NOTES
Trimmed refrigerators are designed to be
customized with decorative panels. Field-
installed 1/2" or 3/4" custom door, drawer
and grille panels are required. For 3/4"
raised panels, routing is required. The router
depth is 1/4" all the way around the panel’s
backs. Additional panel width reductions
are required per the diagrams shown. This
will create “picture frame’ routing allowing
the panels to slide into the attached door,
drawer and grille trims.
Maximum total panel weight:
• Fresh food door panels – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs
Note: For panels constructed with rails and
stiles (5-panel), the rails must be a minimum
of 3" wide and stiles must be a minimum of
4" wide.
Door Handles
Door handles not included. Custom handles
supplied by your cabinet maker may be used.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit custom panels. Kit
includes one handle – 30 1/2" long. Order
2 kits from your Monogram supplier.
ZKHCSS2: Custom European tubular handle
designed to fit custom panels. Kit includes 2
handles. Door handle is 44 3/16" and drawer
handle is 33 3/16".
Order ZUG2: Unified grille kit for
dual installation. Maximum total panel
weight - 25 lbs.
ZKHCT: Handle side trim for left-hand and
right-hand door. For use on a custom panel
when using a custom handle.
FLUSH INSET INSTALLATION
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
A B C D
38" 10 11/16" 46 9/16" 22 7/16"
PANEL DIMENSIONS
FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION
3/4" RAISED DOOR PANEL ROUTING
3/4"
11/32"
1/4"
3/16"
1/4" 7/16"
DETAIL TOP
DETAIL BOTTOM
DETAIL
LEFT SIDE
DETAIL RIGHT
SIDE
2-1/16" 2-1/16"
ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"
1/4"
3/32"
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
LEFT
SIDE
RIGHT
SIDE
Front
Back
Front
NOTE: Routed areas should be
finished as they may be visible
when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back

NOTES
FLUSH INSET INSTALLATION
3/4" RAISED GRILL PANEL ROUTING
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
DETAIL TOP
DETAIL BOTTOM
3/16"
1-11/16"
ROUTER DEPTH 1/4"
DETAIL
LEFT SIDE
DETAIL RIGHT
SIDE
2-1/16" 2-1/16"
ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"
1/4"
3/32"
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
LEFT
SIDE
RIGHT
SIDE
Front
Back
Trimmed refrigerators are designed to be
customized with decorative panels. Field-
installed 1/2" or 3/4" custom door, drawer
and grille panels are required. For 3/4"
raised panels, routing is required. The router
depth is 1/4" all the way around the panel’s
backs. Additional panel width reductions
are required per the diagrams shown. This
will create “picture frame’ routing allowing
the panels to slide into the attached door,
drawer and grille trims.
Maximum total panel weight:
• Fresh food door panels – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs
Note: For panels constructed with rails and
stiles (5-panel), the rails must be a minimum
of 3" wide and stiles must be a minimum of
4" wide.
Door Handles
Door handles not included. Custom handles
supplied by your cabinet maker may be used.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit custom panels. Kit
includes one handle – 30 1/2" long. Order
2 kits from your Monogram supplier.
ZKHCSS2: Custom European tubular handle
designed to fit custom panels. Kit includes 2
handles. Door handle is 44 3/16" and drawer
handle is 33 3/16".
Order ZUG2: Unified grille kit for
dual installation. Maximum total panel
weight - 25 lbs.
ZKHCT: Handle side trim for left-hand and
right-hand door. For use on a custom panel
when using a custom handle.
3/4" RAISED DRAWER PANEL ROUTING
Front
NOTE: Routed areas should be
finished as they may be visible
when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
Front
NOTE: Routed areas should be
finished as they may be visible
when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
LEFT
SIDE
RIGHT
SIDE
Front
Back
3/4"
11/32"
1/4"
3/16"
1/4" 7/16"
DETAIL TOP
DETAIL BOTTOM
2 1/16" 2 1/16"
ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"
DETAIL
LEFT SIDE
DETAIL RIGHT
SIDE
ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16

AMounting the junction box in this
location will also allow for front
accessibility through access panel.
BWater supply area.
WARNING:
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
The information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
The information below applies to all
installation constructions:
• A wall bracket, bolts and toggles will
be supplied with the unit.
• The bolts will be used to attach bracket
to wall in 4 locations. Two of the
locations must penetrate the center of
the wall studs.
• The toggles are used for stability in
drywall and when metal studs are
encountered. Lag bolts are used in
wood studs.
• In installation opening, measure 82"
from floor and draw a horizontal line.
• Locate and mark the wall studs on
horizontal line. Verify at least two studs
have their centerlines within the center
32.5" of installation opening to ensure
2 wall studs are penetrated.
• The bracket will be centered left to
right in opening with bottom of bracket
on the horizontal line.
• When unit is placed in opening, the
bracket tabs will align with openings
in back of the unit. The unit will be
secured to the bracket using supplied
“L” bolts.
See Installation Instructions for
detailed instructions.
FLUSH INSTALLATION
ZIC360NHLH_RH
39" (99.1) Flush inset width
37 1/2" (95.3)
Width between cleats
3/4" (1.9)
Width of side cleats
5 3/8" (13.7)
1/2" (1.3)
26 3/16" (66.5)
Flush inset depth
20 13/16" (52.9)
Depth to cleat
FRONT VIEWSIDE VIEW
TOP VIEW
3 1/2"
(8.9)
W
Finished cleats
Finished cleats
Case Trim
1/2" Panel
Case
Door
6"
(15.2)
24 3/16"
(61.4)
7"
(17.8)
7"
(17.8)
10"
(25.4)
3 1/2"
(8.9)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
84"
(213.4)
height
to cleat
85"
(215.9)
WATER
3 1/2"
(9.0)
NOTES
FLUSH INSET INSTALLATION 1/2" PANELS FLUSH INSET INSTALLATION
A
B
ANTI-TIP BRACKET
24" (61.0)
1 1/2"
(3.8)
3"
(7.6)
7/16" (1.1)
Trim overlap
35 1/2" (90.2)
2 5/16"
(5.9)
SIDE VIEWFRONT VIEW
ZIC360NXRH
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC. 6"
(15.2)
10"
(25.4)
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
81 1/2"
(207.0)
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0)
WATER
10" (25.4)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16

NOTES
The 1/2" overlay panel must be secured
to a .10" spacer panel and a 1/4" thick
backer panel, which slides into the trim.
Assemble the panels with glue and
screws:
• Center the spacer panel on the backer
panel, left to right and top to bottom.
Secure the panels with glue.
• Refer to the chart for locating the backer
panel to the overlay panel. Secure
the overlay panel to the backer panel
with glue and screws. Screws must be
countersunk into the backer panel
Order ZUG2: Unified grille kit for dual
installation. Maximum total panel
weight – 25 lbs.
Note: For panels constructed with rails
and stiles (5-panel), the rails must be a
minimum of 3" wide and stiles must be a
minimum of 4" wide.
FLUSH INSET INSTALLATION
FLUSH INSET 1/2" PANEL DIMENSIONS
1/2" OVERLAY PANEL ROUTING DIMENSIONS
A B C D
1/4" Backer Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8"
.10" Space Panel 32 1/2" 7 5/8" 44 11/16" 20 1/2"
1/2" Overlay Panel 38" 10 11/16" 46 9/16" 22 7/16"
A B C D
Fresh Food Panel 2 1/16" 2 1/16" 5/16" 3/16"
Freezer Panel 2 1/16" 2 1/16" 5/16" 3/16"
Grille Panel 2 1/16" 2 1/16" 1 11/16" 3/16"
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
PANEL DIMENSIONS
C
D
A B
Grille Back
C
D
AB
Hinge Side
Backer with
Overlay Panel
Assembly
Door Panel Back
C
D
AB
Freezer Drawer
1/2"
Overlay
Panel
1/4"
Backer
Panel
Door
.10"
Spacer
PANEL DIMENSIONS
ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16

NOTES
FLUSH INSET INSTALLATION
Trimmed refrigerators are designed to be
customized with decorative panels. Field-
installed 1/2" or 3/4" custom door, drawer
and grille panels are required. For 3/4"
raised panels, routing is required. The router
depth is 1/4" all the way around the panel’s
backs. Additional panel width reductions
are required per the diagrams shown. This
will create “picture frame’ routing allowing
the panels to slide into the attached door,
drawer and grille trims.
AA separate 115V, 60Hz, 15- or 20-amp
power supply is recommended for each
product.
Maximum total panel weight:
• Fresh food door panels – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Unied grille panel – 25 lbs
Door Handles
Door handles not included. Custom handles
supplied by your cabinet maker may be used.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit custom panels. Kit
includes one handle – 30 1/2" long. Order
2 kits from your Monogram supplier.
ZKHCSS2: Custom European tubular handle
designed to fit custom panels. Kit includes 2
handles. Door handle is 44 3/16" and drawer
handle is 33 3/16".
Order ZUG2: Unified grille kit for
dual installation. Maximum total panel
weight - 25 lbs.
ZKHCT: Handle side trim for left-hand and
right-hand door. For use on a custom panel
when using a custom handle.
The 1/2" overlay panel must be secured to
a .10" spacer panel and a 1/4" thick backer
panel, which slides into the trim.
Assemble the panels with glue and screws:
• Center the spacer panel on the backer
panel, left to right and top to bottom. Secure
the panels with glue.
• Refer to the chart for locating the backer
panel to the overlay panel. Secure the
overlay panel to the backer panel with glue
and screws. Screws must be countersunk
into the backer panel
FLUSH INSET 1/2" PANEL DIMENSIONS DUAL INSTALLATION
PANEL DIMENSIONS
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
Fresh
Food
Panel
Freezer Drawer Panel
E
B
C
D
A B C D E
1/4" Backer Panel 69 7/8" 8 7/8" 46 1/16" 21 7/8" 33 7/8"
.10" Space Panel 68 1/2" 7 5/8" 44 11/16" 20 1/2" 32 1/2"
1/2" Overlay Panel 74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"
3/4" or 1/2" DUAL INSTALLATIONS
ZIC360NHLH_ZIC360NHRH
75" (190.5)
Finished Width
26 3/16" (66.5)
Min. Cutout Depth
24 3/16" (61.4)
4 5/16"
(10.9)
5 1/2"
(13.9)
9"
(22.9)
85"
(215.9)
Finished
Opening
3 1/2"
(8.9)
W
FRONT VIEW
ELEC. 5 1/2"
(13.9)
9"
(22.9)
3 1/2"
(8.9)
15" (38.1) min
To wall 15" (38.1) min To wall
1"
(2.5)
115˚
Door swing 115˚ Door swing
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
7"
(17.8) 7" (17.8)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
7 1/2"
(19.1) 7 1/2" (19.1)
A
ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
NOTES
FLUSH INSET INSTALLATION
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
Fresh
Food
Panel
Freezer Drawer Panel
E
B
C
D
A B C D E
74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"
PANEL DIMENSIONS
FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION
Trimmed refrigerators are designed to be
customized with decorative panels. Field-
installed 1/2" or 3/4" custom door, drawer
and grille panels are required. For 3/4"
raised panels, routing is required. The router
depth is 1/4" all the way around the panel’s
backs. Additional panel width reductions
are required per the diagrams shown. This
will create “picture frame’ routing allowing
the panels to slide into the attached door,
drawer and grille trims.
Maximum total panel weight:
• Fresh food door panels – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Unied grille panel – 25 lbs
Door Handles
Door handles not included. Custom handles
supplied by your cabinet maker may be used.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit custom panels. Kit
includes one handle – 30 1/2" long. Order
2 kits from your Monogram supplier.
ZKHCSS2: Custom European tubular handle
designed to fit custom panels. Kit includes 2
handles. Door handle is 44 3/16" and drawer
handle is 33 3/16".
Order ZUG2: Unified grille kit for
dual installation. Maximum total panel
weight - 25 lbs.
ZKHCT: Handle side trim for left-hand and
right-hand door. For use on a custom panel
when using a custom handle.
3/4" RAISED DOOR AND DRAWER PANEL ROUTING - (SEE PAGE 5
FOR 3/4" GRILLE PANEL ROUTING DIAGRAMS)
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
Front
NOTE: Routed areas should be
finished as they may be visible
when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back
HINGE
SIDE
HANDLE
SIDE
Front
Back
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
3/4"
11/32"
1/4"
3/16"
1/4" 7/16"
DETAIL TOP
DETAIL BOTTOM
2 1/16" 3/16"
ROUTER DEPTH 1/4"
DETAIL HINGE
SIDE
DETAIL HANDLE
SIDE

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
NOTES
FLUSH INSET INSTALLATION
AIn a side-by-side installation of a left-
and-right-hand door swing product, 1"
clearance between the units is required.
Order ZUG2 custom panel unified grille
kit for this installation.
3/4" or 1/2" DUAL PRODUCT CLEARANCES
ZIC360NHLH_ZIC360NHRH
75" (190.5)
Finished Width
26 3/16" (66.5)
Min. Cutout Depth
24 3/16" (61.4)
4 5/16"
(10.9)
5 1/2"
(13.9)
9"
(22.9)
85"
(215.9)
Finished
Opening
3 1/2"
(8.9)
W
FRONT VIEW
ELEC. 5 1/2"
(13.9)
9"
(22.9)
3 1/2"
(8.9)
15" (38.1) min
To wall 15" (38.1) min To wall
1"
(2.5)
115˚
Door swing 115˚ Door swing
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
7"
(17.8) 7" (17.8)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
7 1/2"
(19.1) 7 1/2" (19.1)
A

OVERALL DIMENSIONS
AFTER PANEL INSTALL
ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
STANDARD INSTALLATION
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
SPECIFICATIONS
Overall Width 36" (91.4 cm)
Overall Height 84" (213.4 cm)
Overall Depth 25 3/8" (64.5 cm)
Door Clearance 36 3/4" (93.4 cm)
Cutout Width 35 1/2" (90.2 cm)
Cutout Height 83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 640 lb (290.3 kg)
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimension may vary due to manufacturing tolerances.
25 1/4" (64.1)
23 7/8" (60.7)
1 7/8"
(4.8)
46 1/4"
(117.5)
*73 1/4"
(186.1)
9 7/8"
(25.1)
*26 1/2"
(67.3)
36" (91.5)
*84"
(213.4)
*24 1/8"
(61.3)
*26"
(66.0)
*3 5/8"
(9.2) SIDE VIEWFRONT VIEW
*83 1/2"
(212.1)
36 3/4"
(93.4)
35" (89.0)
Case width
TOP VIEW
ZIC360NXRH
* Shipping height. Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
** Allow 25" (63.5) min
clearance for 130˚
door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
25 1/4" (64.1)
23 7/8" (60.7)
1 7/8"
(4.8)
46 1/4"
(117.5)
*73 1/4"
(186.1)
9 7/8"
(25.1)
*26 1/2"
(67.3)
36" (91.5)
*84"
(213.4)
*24 1/8"
(61.3)
*26"
(66.0)
*3 5/8"
(9.2) SIDE VIEWFRONT VIEW
*83 1/2"
(212.1)
36 3/4"
(93.4)
35" (89.0)
Case width
TOP VIEW
ZIC360NXRH
* Shipping height. Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
** Allow 25" (63.5) min
clearance for 130˚
door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
**These refrigerators are equipped with a 3-position door stop. The factory-set 130° door swing
can be adjusted to 90° or 130° for standard installation if clearances to adjacent cabinets or
walls is restricted. Allow a 15" minimum clearance to wall for pan removal. If the 90° door stop
position is used, pan access is maintained, but pan removal is restricted.

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
24" (61)
1 9/16"
(3.97)
3 1/8"
(7.93) 35 1/2" (90.2)
2 5/16"
(5.874)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
*84 1/2"
(214.6)
*Trim will overlap
additional 7/16"
6"
(15.24)
10"
(25.4)
ELEC.
SIDE VIEW FRONT VIEW
TOP VIEW
W
STANDARD INSTALLATION
ZIC360NHLH_RH
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0) 3 1/2"
(8.9)
NOTES
STANDARD INSTALLATION
AMounting the junction box in this
location will also allow for front
accessibility through access panel.
BWater supply area.
WARNING:
The refrigerator is top heavy and
must be secured to prevent the
possibility of tipping forward. Failure
to do so may result in death or
serious injury.
The information below is for cabinet
design only. When installing the
anti-tip system you must use the
product installation instructions.
The information below applies to all
installation constructions:
• A wall bracket, bolts and toggles
will be supplied with the unit.
• The bolts will be used to attach
bracket to wall in 4 locations. Two
of the locations must penetrate the
center of the wall studs.
• The toggles are used for stability in
drywall and when metal studs are
encountered. Lag bolts are used in
wood studs.
• In installation opening, measure
81 1/2" from oor and draw a
horizontal line.
• Locate and mark the wall studs on
horizontal line. Verify at least two
studs have their centerlines within
the center 32.5" of installation
opening to ensure 2 wall studs are
penetrated.
• The bracket will be centered left
to right in opening with bottom of
bracket on the horizontal line.
• When unit is placed in opening,
the bracket tabs will align with
openings in back of the unit. The
unit will be secured to the bracket
using supplied “L” bolts.
See Installation Instructions for
detailed instructions.
A
B
STANDARD INSTALLATION
ANTI-TIP BRACKET
24" (61.0)
1 1/2"
(3.8)
3"
(7.6)
7/16" (1.1)
Trim overlap
35 1/2" (90.2)
2 5/16"
(5.9)
SIDE VIEWFRONT VIEW
ZIC360NXRH
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC. 6"
(15.2)
10"
(25.4)
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
81 1/2"
(207.0)
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0)
WATER
10" (25.4)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET

PANEL ASSEMBLY CROSS SECTION
PANEL ASSEMBLY CROSS SECTION
PANEL DIMENSIONS
PANEL DIMENSIONS
.25" + .10" + .75" = 1.10" Total Panel Thickness
ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
STANDARD 3/4" OVERLAY PANEL DIMENSIONS SINGLE INSTALLATION
STANDARD 1/4" FRAMED PANEL DIMENSIONS SINGLE INSTALLATION STANDARD INSTALLATION
A B C D
1/4" Framed Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8"
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
Door
1/4" Framed Panel
Supplied Handles
Trim
A B C D
1/4" Backer Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8"
.10" Spacer Panel 32 1/2" 7 5/8" 44 11/16" 20 1/2"
3/4" Overlay Panel 34 1/8" 9" 46 5/16" 22"
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
Door 1/4" Backer Panel
.10" Spacer Panel
Supplied Handles
Trim
3/4" Overlay Panel
3/4" Overlay Panels:
The decorative panels slide into the trim.
The overlay panel must be secured to a
1/4"-thick backer panel which slides into
the trim. A spacer panel 0.10" thick must
be placed between the overlay and
backer panels.
Center each panel over the other. Assemble
the panels with glue and screws. Screws
must be countersunk into the
backer panel.
NOTE: Left-to-right offset is not always equal
to top-to-bottom offset.
Maximum total panel weight:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs.
Door Handles:
The supplied handles can be adjusted to
accommodate both framed or overlay
panels. Custom handles of your choice,
supplied by your cabinet maker, can also
be installed.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4" overlay panels.
ZKHCSS2: European tubular handle
designed to fit 3/4" panels. Kit includes 2
handles.
Door handle is 44 3/16" and drawer handle
is 33 3/16".
NOTES
Trimmed refrigerators are designed to
be customized with decorative panels.
Field-installed custom door and grille
panels are required.
1/4" Framed Panels:
For 1/4" thick custom panels ordered from
your cabinet maker. The decorative panels
slide into the trim.
Maximum total panel weight:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs.

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
NOTES
Side panels must be used
whenever the sides of
the refrigerator will be
exposed. The 1/4" side
panels will slip into the
side case trim. Secure the
panels to the refrigerator
with stick-on hook and
loop fastener strips. Order
the side panels from the
cabinet manufacturer.
CUSTOM SIDE PANELS
F
2 9/16"
(6.5)
*3" - 4"
(7.6 - 10.2)
*Depending
on installation
height
1 7/8"
(4.8)
24" (61.0)
3/16"
(.5)
*84”
(213.4)
*Depending
on installation
*84"
(213.4)
*Depending
on installation
height
ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH
ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
STANDARD INSTALLATION

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
NOTES
STANDARD INSTALLATION
STANDARD 1/4" FRAMED PANEL DIMENSIONS DUAL INSTALLATION
PANEL DIMENSIONS
1/4"
Framed
Panel
A69 7/8"
B8 7/8"
C46 1/16"
D21 7/8"
E33 7/8"
PANEL ASSEMBLY
CROSS SECTION Door
1/4" Framed Panel
Supplied Handles
Trim
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
Fresh
Food
Panel
Freezer Drawer Panel
E
B
C
D
Trimmed refrigerators are designed to
be customized with decorative panels.
Field-installed custom door and grille
panels are required.
1/4" Framed Panels:
For 1/4" thick custom panels ordered from
your cabinet maker. The decorative panels
slide into the trim.
Maximum total panel weight:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 25 lbs.
Order ZUG2: Unified grille kit for dual
installation
71 1/2" (181.6)
Finished Width
24" (60.9)
Min. Cutout Depth
24 3/16" (61.4)
2 5/16"
(5.9)
6"
(15.2)
10"
(25.4)
83 1/2" min
84 1/2" max
(212.1-214.6)
Finished Opening
ZIC360NXLH_ZIC360NXRH_ZICP360NXLH_ZICP360NXRH
ZICS360NXLH_ZICS360NXRH
FRONT VIEW
ELEC. 6"
(15.2)
10"
(25.4)
3 1/2"
(8.9)
25" min
(63.5)
To wall
25" min
(63.5)
To wall
1"
(2.5)
130˚
Door swing 130˚ Door swing
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
5"
(12.7) 5" (12.7)
WATER
10" (25.4)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
5 3/4"
(14.6) 5 3/4" (14.6)
AA separate 115V, 60Hz, 15- or 20-amp
power supply is recommended for each
product.
Additional cutout width may be required when
side panels are used.
DUAL INSTALLATIONS
A

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
Fresh
Food
Panel
Freezer Drawer Panel
E
B
C
D
NOTES
STANDARD INSTALLATION
DUAL PRODUCT CLEARANCES
71 1/2" (181.6)
Finished Width
24" (60.9)
Min. Cutout Depth
24 3/16" (61.4)
2 5/16"
(5.9)
6"
(15.2)
10"
(25.4)
83 1/2" min
84 1/2" max
(212.1-214.6)
Finished Opening
ZIC360NXLH_ZIC360NXRH_ZICP360NXLH_ZICP360NXRH
ZICS360NXLH_ZICS360NXRH
FRONT VIEW
ELEC. 6"
(15.2)
10"
(25.4)
3 1/2"
(8.9)
25" min
(63.5)
To wall
25" min
(63.5)
To wall
1"
(2.5)
130˚
Door swing 130˚ Door swing
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
5"
(12.7) 5" (12.7)
WATER
10" (25.4)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
5 3/4"
(14.6) 5 3/4" (14.6)
A
STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION
PANEL ASSEMBLY
CROSS SECTION
PANEL DIMENSIONS
1/4"
Backer
Panel
.10"
Spacer
Panel
3/4"
Overlay
Panel
A69 7/8" 68 1/2" 70 1/8"
B8 7/8" 7 5/8" 9"
C46 1/16" 44 11/16" 46 5/16"
D21 7/8" 20 1/2" 22"
E33 7/8" 32 1/2" 34 1/8"
.25" + .10" + .75" =
1.10" Total Panel Thickness
Door 1/4" Backer Panel
.10" Spacer Panel
Supplied Handles
Trim
3/4" Overlay Panel
3/4" Overlay Panels:
The decorative panels slide into the trim. The
overlay panel must be secured to a 1/4"-thick
backer panel which slides into the trim. A
spacer panel 0.10" thick must be placed
between the overlay and backer panels.
Center each panel over the other. Assemble
the panels with glue and screws. Screws must
be countersunk into the backer panel.
NOTE: Left-to-right offset is not always equal
to top-to-bottom offset.
Maximum total panel weight:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 25 lbs.
Order ZUG2: Unified grille kit for dual
installation
Door Handles:
The supplied handles can be adjusted to
accommodate both framed or overlay panels.
Custom handles of your choice, supplied by
your cabinet maker, can also be installed.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4" overlay panels.
ZKHCSS2: European tubular handle designed
to fit 3/4" panels. Kit includes 2 handles.
Door handle is 44 3/16" and drawer handle
is 33 3/16".
AIn a side-by-side installation of a left-
and-right-hand door swing product, 1"
clearance between the units is required.
Order ZUG2: custom panel unified grille kit for
one continuous grille panel.

FEATURES AND BENEFITS
Monogram®36" Built-In Bottom-freezer Refrigerator ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator
Product Specification Revised 5/16
Custom Appearance - Allows personalization
with cabinet-compatible panels an custom
handles
Upfront Electronic Controls with Digital Readout
- Allows precise temperature settings and are
positioned for maximum ease of use
Humidity Controlled Vegetable Compartments
and Sealed Snack Pans - Help maintain freshness
and help preserve foods longer
Adjustable, Spill Proof Glass Shelves - Make it
easy to customize storage to handle foods and
containers of various sizes
2 Sealed Deli Pans with Full-Extension Slides
Six Adjustable Door Bins - Offer added storage
flexibility
GE Water™Filtration System - Delivers clean,
great tasting ice
R