Monoprice 605030 User manual

300-Watt Studio Audio Amplifier
P/N 605030
User's Manual

2
CONTENTS
SAFETY WARNINGS AND GUIDELINES............................................................................................................................................3
INTRODUCTION .....................................................................................................................................................................................................4
FEATURES.................................................................................................................................................................................................................... 5
CUSTOMER SERVICE......................................................................................................................................................................................... 5
PACKAGE CONTENTS ...................................................................................................................................................................................... 6
PRODUCT OVERVIEW...................................................................................................................................................................................... 6
Front Panel .......................................................................................................................................................................................................... 6
Rear Panel..............................................................................................................................................................................................................7
STEREO OPERATION..........................................................................................................................................................................................8
BRIDGED OPERATION...................................................................................................................................................................................... 9
CONNECTOR WIRING.......................................................................................................................................................................................11
BLOCK DIAGRAM................................................................................................................................................................................................13
TECHNICAL SUPPORT ....................................................................................................................................................................................14
SPECIFICATIONS.................................................................................................................................................................................................14
REGULATORY COMPLIANCE................................................................................................................................................................... 15
Notice for FCC................................................................................................................................................................................................ 15
Notice for Industry Canada ............................................................................................................................................................... 16

3
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra attention to these
safety warnings and guidelines. Please keep this manual in a safe place for future reference.
•This device is intended for indoor use only.
•Do not expose this device to water or moisture of any kind. Do not place drinks or
other containers with moisture on or near the device. If moisture does get in or on
the device, immediately unplug it from the power outlet and allow it to fully dry
before reapplying power.
•Do not touch the device, the power cord, or any other connected cables with wet
hands.
•Do not install this device on an unstable surface where it could fall and cause either
personal injury or damage to the device and/or other equipment.
•Do not subject the product to extreme force, shock, or fluctuations in temperature
or humidity.
•Do not expose this device to excessively high temperatures. Do not place it in, on,
or near a heat source, such as a fireplace, stove, radiator, etc. Do not leave it in
direct sunlight.
•This device ventilates excessive heat through the slots and openings in the case. Do
not block or cover these openings. Ensure that the device is in an open area where
it can get sufficient airflow to keep from overheating.
•Do not place or install this device in an area where it can be exposed to excessive
amounts of dust, humidity, oil, smoke, or combustible vapors.
•Use only in a well-ventilated area. Do not use in close, confined spaces.
•Prior to operation, check the unit and power cord for physical damage. Do not use if
physical damage has occurred.
•Before plugging the unit into a power outlet, ensure that the outlet provides the
same type and level of power required by the device.

4
•This device uses a grounded power cord and requires a ground connection for safe
operation. Ensure that the power source has a proper ground connection. Do not
modify the plug or use a "cheater" plug to bypass the ground connection.
•Disconnect the unit from the power source when replacing the fuse. Replace the
fuse only with the same type.
•Unplug this device from the power source when not in use.
•Take care to prevent damage to the power cord. Do not allow it to become
crimped, pinched, walked on, or become tangled with other cords. Ensure that the
power cord does not present a tripping hazard.
•Never unplug the unit by pulling on the power cord. Always grasp the connector
head or adapter body.
•Ensure that power is turned off and disconnected before making any electrical
connections.
•Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or
detergents. For stubborn deposits, moisten the cloth with warm water.
•This device has no user serviceable parts. Do not attempt to open, service, or
modify this device.
INTRODUCTION
This 300-Watt Studio Audio Amplifier packs 300 watts of power into a compact form
factor, which takes up only 1U of rack space. It can be used as a stereo amplifier or can be
bridged for mono mode. In stereo mode it produces 150 watts per channel RMS (300 watts
per channel peak) into a 4-ohm load. It is stable when using reactive or mismatched loads,
so for example, you can connect a 2-ohm speaker to one channel and an 8-ohm speaker to
the other without any problems. It features an extremely flat 20Hz ~ 20kHz (+0, -1dB)
frequency response with less than 0.05% THD+N and more than 96dB signal-to-noise ratio.
Built-in protection circuitry includes full short circuit, open circuit, thermal, ultrasonic, and
RF protection. It also features a power on/off muting function to prevent popping in the
speakers when power is turned on or off. There is a selectable limiter, which serves as a
brick wall on volume to prevent high volume levels from driving the amplifier into clipping.

5
FEATURES
•Class D amplifier
•High current switching power for high power output, low noise, and low distortion
•Extremely flat 20Hz ~ 20kHz (+0, -1dB) frequency response with less than 0.05%
THD+N
•Balanced 1/4" TRS and XLR inputs
•Unbalanced 1/4" TS and NL4 speaker outputs
•Built-in optional limiter helps prevent clipping
•Short circuit, open circuit, thermal, ultrasonic, and RF protection
•Stable with reactive and mismatched loads
•Power on/off muting function
•Separate gain controls for each channel
•Signal and clipping LEDs for each channel
•Power and protection LEDs
•Bridgeable for high-power mono operation
•1U height
•Includes rack mount ears
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering,
purchasing, and delivery experience is second to none. If you have any problem with your
order, please give us an opportunity to make it right. You can contact a Monoprice
Customer Service representative through the Live Chat link on our website
www.monoprice.com or via email at su[email protected]. Check the website for
support times and links.

6
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items listed
below. If anything is missing or damaged, please contact Monoprice Customer Service for a
replacement.
1x 300-Watt Studio Audio Amplifier
1x AC Power Cord
PRODUCT OVERVIEW
Front Panel
1. POWER: The rocker switch turns the amplifier on or off.
2. CH1/CH2: Level control knobs allow independent volume control for each channel.
3. POWER LED: The LED illuminates blue when the amplifier is powered on.
4. SIG LEDS: Two LEDs, one for each channel, illuminate green when a signal is
detected.
5. PROT LED: The LED illuminates red when the amplifier is in thermal protection
mode. When thermal protection is active, the speaker system is disconnected from
each channel's amplifier. Once the amplifier has cooled sufficiently, the LED will turn
off and the speaker system will be reconnected to the amplifiers. To prevent the
thermal protection circuit from activating, improve cooling/ventilation and/or lower
the volume levels.
6. CLIP LEDS: Two LEDs, one for each channel, illuminate red when the amplifier is
clipping. Lower the volume levels until the LEDs no longer illuminate.

7
7. INTAKE VENT: The amplifier draws in cooling air through the vent on the front panel
and exhausts it through the vents on the rear and side panels.
Rear Panel
1. AC INPUT/FUSE HOLDER: Grounded panel connector for connecting the included
AC power cord. The fuse holder is inset in the lower half of the connector.
2. CH1 XLR INPUT: The XLR input accepts any balanced or unbalanced low impedance
line level source. The XLR jack is wired in parallel with the TRS jack to allow daisy
chaining this amplifier to another amplifier's input.
3. CH1 TRS INPUT: The 1/4" TRS input accepts any balanced or unbalanced low or high
impedance line level source. The TRS jack is wired in parallel with the XLR jack to
allow daisy chaining this amplifier to another amplifier's input.
4. CH2 XLR INPUT: The XLR input accepts any balanced or unbalanced low impedance
line level source. The XLR jack is wired in parallel with the TRS jack to allow daisy
chaining this amplifier to another amplifier's input.
5. CH2 TRS INPUT: The 1/4" TRS input accepts any balanced or unbalanced low or high
impedance line level source. The TRS jack is wired in parallel with the XLR jack to
allow daisy chaining this amplifier to another amplifier's input.
6. MODE: Use this button to select stereo or mono bridge mode. When in the STEREO
position, the channel 1 input connects to the channel 1 amp and the channel 2 input
connects to the channel 2 amp. When in the BRIDGE position, the channel 1 input is
connected to the mono bridged amps. See the BRIDGED OPERATION section for
more details.
7. CH1 NL4 OUTPUT: 2-pin NL4 unbalanced speaker output connector.
8. CH1 TS OUTPUT: 2-pin 1/4" TS unbalanced speaker output connector.

8
9. CH2 NL4 OUTPUT: 2-pin NL4 unbalanced speaker output connector.
10. CH2 TS OUTPUT: 2-pin 1/4" TS unbalanced speaker output connector.
11. LIMIT: Use this button to turn the built-in limiter on or off.
12. EXHAUST VENT: The amplifier draws in cooling air through the vent on the front
panel and exhausts it through the vents on the rear and side panels.
STEREO OPERATION
The amplifier can be operated as a standard, 2-channel stereo amplifier. To enable stereo
operation, the MODE button (6) on the rear panel must be set to the STEREO position (out).
When in stereo mode, each channel operates independently, with its own dedicated input
connectors, sensitivity level controls, signal indicator LEDs, automatic limiter, fault
protection circuitry, power amp, and speaker outputs. Stereo mode supports speaker loads
down to 2 ohms.
Following is a sample connection diagram for basic stereo operation.

9
BRIDGED OPERATION
The amplifier can be operated as a single, mono amplifier with more power than either
single channel in stereo mode. To enable mono bridged operation, the MODE button (6) on
the rear panel must be set to the BRIDGE position (in). When in mono mode, the amplifier
uses the CH1 input jacks and level control, although each channel retains its own
protection modes. Mono bridged mode supports speaker loads down to 4 ohms.
Unlike stereo operation, which uses each channel's output connectors to connect the
speakers, mono bridge operation uses a single pin from each output connector to connect
the speaker. When in mono bridged mode, connect the positive pin on the channel 1
output connector to the speaker's positive connection and the positive pin on the channel
2 output connector to the speaker's negative connection.
Following is a sample connection diagram for using a single 605030 amplifier for mono
bridged operation to drive a single speaker, such as a subwoofer.

10
Following is a sample connection diagram for using two 605030 amplifiers, each in mono
bridged mode, for stereo operation. Note that in this operating example, the second
amplifier's input is daisy chained to the first amplifier's inputs. The two input connectors for
each channel on the amplifier are wired in parallel to allow daisy chaining multiple
amplifiers.

11
CONNECTOR WIRING
The following diagrams illustrate the proper wiring for TRS, TS, and XLR connectors for
various functions.

12

13
BLOCK DIAGRAM
The following block diagram illustrates the amplifiers internal circuitry.

14
TECHNICAL SUPPORT
Monoprice is pleased to provide free, live, online technical support to assist you with any
questions you may have about installation, setup, troubleshooting, or product
recommendations. If you ever need assistance with your new product, please come online
to talk to one of our friendly and knowledgeable Tech Support Associates. Technical
support is available through the online chat button on our website www.monoprice.com
or through email by sending a message to t[email protected]. Check the website for
support times and links.
SPECIFICATIONS
Model
605030
Operating Modes
2-channel stereo and mono bridged
Stereo Output Power (RMS/Peak)
(Both Channels Driven)
2-ohm load: 2x 250W/500W
4-ohm load: 2x 150W/300W
8-ohm load: 2x 100W/200W
Mono Bridged Output Power (RMS/Peak)
4-ohm load: 1x 500W/1000W
8-ohm load: 1x 360W/720W
Input Sensitivity (Limiter Off)
0.9 ~ 1.1V (±1 dBv)
Input Impedance
20 kΩbalanced or 10 kΩunbalanced
Frequency Response
(at 10dB Rated Output Power)
20Hz ~ 20kHz (+0, -1 dB)
Voltage Gain
28 ±0.5dB
THD+N
(Ref. 1kHz, 12.5% Rated Power, A-weighted)
< 0.05%
Signal-to-Noise Ratio
(Ref. Rated Power, A-weighted)
> 96dB

15
Protection Features
Full short circuit, Open circuit, Thermal,
Ultrasonic, and RF protection; stable into
reactive or mismatched loads; power
on/off muting
Controls
Front: Power on/off switch, Channel 1 level,
Channel 2 level
Rear: Stereo/Bridge switch, Limiter on/off
switch
LED Indicators
Green signal for each channel, Red clipping
for each channel, Blue power, Red
protection
Input Connectors
1/4" TRS balanced, XLR balanced
Output Connectors
1/4" TS unbalanced, NL4 unbalanced
Input Power
110 ~ 120 VAC, 50/60Hz ±10%
220 ~ 240 VAC, 50/60Hz ±10%
Maximum Power Consumption
450 watts
Fuse Type
110 ~ 120 VAC: T6.3AL AC250V
220 ~ 240 VAC: T4.0AL AC250V
Dimensions
19.0" x 11.1" x 1.7" (483 x 281 x 44 mm)
Weight
8.2 lbs. (3.7 kg)
REGULATORY COMPLIANCE
Notice for FCC
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must

16
accept any interference received, including interference that may cause undesired
operation.
Modifying the equipment without Monoprice's authorization may result in the equipment
no longer complying with FCC requirements for Class B digital devices. In that event, your
right to use the equipment may be limited by FCC regulations, and you may be required to
correct any interference to radio or television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Notice for Industry Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.