Monoprice DARK MATTER 45548 User manual

32" Gaming Display
PN 43548 USER'S MANUAL

2
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra attention to
these safety warnings and guidelines. Please keep this manual in a safe place for
future reference.
•This device is intended for indoor use only.
•Do not expose this device to water or moisture of any kind. Do not
place drinks or other containers with moisture on or near the device. If
moisture does get in or on the device, immediately remove it from its
power source and allow it to fully dry before reapplying power.
•Do not touch the device, the power cord, or any other connected
cables with wet hands.
•Do not place the monitor on an unstable surface where it could fall and
cause either personal injury or damage to the monitor and/or other
equipment.
•Do not expose this device to excessive vibration or extreme force,
shock, or fluctuations in temperature or humidity.
•Do not expose this device to excessively high temperatures. Do not
place it in, on, or near a heat source, such as a fireplace, stove, radiator,
etc. Do not leave it in direct sunlight.
•Do not block the ventilation holes in the monitor's casing. Do not place
the monitor in a confined space with inadequate ventilation.
Periodically check the ventilation holes to ensure they do not become
clogged with dust, debris, or nearby items.
•Do not place or install this device in an area where it can be exposed to
excessive amounts of dust, humidity, oil, smoke, or combustible vapors.
•Use only in a well-ventilated area. Do not use in close, confined spaces.
•Prior to operation, check the unit and power cord for physical damage.
Do not use if physical damage has occurred.

3
•Before plugging the unit into a power outlet, ensure that the outlet
provides the same type and level of power required by the device.
•Unplug this device from the power source when not in use.
•Take care to prevent damage to the power cord. Do not allow it to
become crimped, pinched, walked on, or become tangled with other
cords. Ensure that the power cord does not present a tripping hazard.
•Never unplug the unit by pulling on the power cord. Always grasp the
connector head or adapter body.
•Ensure that power is turned off and disconnected before making any
electrical connections.
•Clean using a soft, dry cloth only. Do not use chemical cleaners,
solvents, or detergents. For stubborn deposits, moisten the cloth with
warm water.
•This device has no user serviceable parts. Do not attempt to open,
service, or modify this device.
•Do not leave a single image on the display for a long period of time.
Doing so could cause "burn-in" of the image. It is recommended to use a
variable desktop background and to use a screen saver to prevent
"burn-in". Alternatively, ensure that the monitor is powered off for at
least 2 hours out of every 12.
•Keep the original foam packaging material for use when installing or
removing the included stand.

4
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your
ordering, purchasing, and delivery experience is second to none. If you have any
problem with your order, please give us an opportunity to make it right. You can
contact a Monoprice Customer Service representative through the Live Chat link
on our website www.monoprice.com or via email at [e-mail].
Check the website for support times and links.
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the
items listed below. If anything is missing or damaged, please contact Monoprice
Customer Service for a replacement.
1x 32" Gaming Monitor
1x Stand Stem
1x Stand Base
3x M4x16 Screws
1x DisplayPort® Cable
1x AC Power Adapter
1x AC Power Cord
1x User's Manual

5
PRODUCT OVERVIEW
Connections
1. DC:DC barrel connector for connecting the included AC power adapter.
2. HDMI1: HDMI® input for connecting a video source device.
3. HDMI2: HDMI input for connecting a video source device.
4. DP1: DisplayPort® input for connecting a video source device.
5. DP2: DisplayPort input for connecting a video source device.
6. EARPHONE: 3.5mm audio jack for connecting headphones, an external
amplifier, or a pair of powered speakers.

6
Controls
7. POWER LED: The POWER LED illuminates solid blue when the monitor is
powered on. The POWER LED illuminates solid red when the monitor is
in standby mode. The POWER LED flashes red when the monitor is in
energy saving mode.
8. ROCKER: Use the ROCKER to control the monitor:
•PRESS: With the monitor powered off, momentarily press the
ROCKER to turn the monitor on. With the monitor powered on,
press and hold the ROCKER for 3 seconds to turn the monitor off.
•UP: When a menu is not displayed, push the ROCKER up to cycle
through the inputs. When the top level of the OSD menu, the
Brightness menu, or the Volume menu is displayed, push the
ROCKER up to exit the menu. When a submenu is displayed, push
the ROCKER up to return to the previous menu. If editing a value,
push the ROCKER up to exit editing and cancel any changes.
•DOWN: When a menu is not displayed, push the ROCKER down to
enter the OSD menu. When the OSD menu is displayed, push the
ROCKER down to enter the highlighted submenu or to edit the
highlighted option. If editing a value, push the ROCKER down to
exit editing and save the changes.
•LEFT: When the OSD menu is not displayed, push the ROCKER left
to display the Brightness adjustment menu. When the OSD menu is

7
displayed, push the ROCKER left to move the highlight left. When
editing a value, push the ROCKER left to decrease the value.
•RIGHT: When the OSD menu is not displayed, push the ROCKER
right to display the Volume adjustment menu. When the OSD menu
is displayed, push the ROCKER right to move the highlight right.
When editing a value, push the ROCKER right to decrease the value.
STAND INSTALLATION
Perform the following steps to install the stand.
1. Using the three included M4x16 Screws, attach the Stand Base to the
Stand Stem.
2. Spread a blanket or towel on a flat surface, then place the monitor face
down on the cushioned surface.
3. Remove the screws that are holding the protective plate on the back of
the monitor, then remove the plate. Place the protective plate in a safe
place for future use.

8
4. Insert the monitor plate on the stand assembly into the opening on the
back of the monitor, then secure it in place using the screws removed in
the previous step.
TECHNICAL SUPPORT
Monoprice is pleased to provide free, live, online technical support to assist you
with any questions you may have about installation, setup, troubleshooting, or
product recommendations. If you ever need assistance with your new product,
please come online to talk to one of our friendly and knowledgeable Tech
Support Associates. Technical support is available through the online chat
button on our website www.monoprice.com or through email by sending a
message to [e-mail]. Check the website for support times and
links.
To download the latest drivers, firmware, manuals, etc., go to
www.monoprice.com and type the P/N into the search bar. If available, support
files are linked at the bottom of the product page.

9
SPECIFICATIONS
P/N
43548
Display Size
31.5"
Maximum Resolution
2560 x 1440p
Refresh Rate
165Hz
Video Input
2x HDMI® 2.0, 2x DisplayPort® 1.2
HDCP™ Version
2.2
VESA® Mount Size
100 x 100
Input Power
12 VDC, 5A
AC Adapter Input Power
100 ~ 240 VAC, 50/60 Hz
Maximum Power Consumption
60 watts
Standby Power Consumption
≤ 0.5 watts
Operating Temperature
+32 ~ +104°F (0 ~ +40°C)
Operating Humidity
20 ~ 85 % RH, noncondensing
Storage Temperature
+14 ~ +140°F (-10 ~ +60°C)
Storage Humidity
10 ~ 90% RH, noncondensing
Dimensions (with stand)
28.5" x 19.6" x 7.2" (724 x 498 x 183 mm)
Weight (with stand)
20.9 lbs. (9.5 kg)
Dimensions (without stand)
28.5" x 16.7" x 1.7" (724 x 424 x 43 mm)
Weight (without stand)
15.0 lbs. (6.8 kg)

10
REGULATORY COMPLIANCE
Notice for FCC
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Modifying the equipment without Monoprice's authorization may result in the
equipment no longer complying with FCC requirements for Class B digital
devices. In that event, your right to use the equipment may be limited by FCC
regulations, and you may be required to correct any interference to radio or
television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.