Monoprice Motorized projection screen User manual

Thank you for purchasing a Motorized Projection Screen.
Before use, please read instructions carefully. After installation, store instructions for future reference.
Instruction Manual for
Motorized Projection Screen
ISO9001:2000
International Certification
Monoprice, Inc.
11701 6th Street, Rancho Cucamonga, CA 91730, USA
www.monoprice.com

1
Voltage（ ）V Frequency（ ）Hz Watts（ ）W
230V/120V/100V 50Hz/60Hz 90W/80W
230V/120V/100V 50Hz/60Hz 160W/156W
Metal Casing
End Cap
Screen Fabric
Rod
Description
Elegant Motorized Screen Power Specifications
Application
Applies up to 150" Elegant series
Applies to 180" and up Elegant series
Instruction Manual ( 1pc )
C2 Mounting Bracket for screen sizes
larger than 150" ( 2pcs )
C1 Mounting Bracket for screen
sizes up to 150" ( 2pcs )
Accessories
10 x 30 mm screw and anchor ( 4pcs )
5 ( 1pc )Allen Key
Optional
5 40mm Tapping screw & cap ( 8sets )

2
5
Installation
Installation without bracket
A
A
1
2
3
45
This projection screen should be installed at the best possible viewing position for the audience.
Take out all the parts from the packaging and follow the accessories guideline to ensure you have
all parts. The parts needed will vary depending on which installation you choose to use. For
installation on a wood wall or ceiling, use the 5 x 40 screws. For installation on a drywall, use the
10 x 30 screws with anchors.
Wall Mount
Using a tape measure, measure the distance between the two keyholes on the casing ( Figure 1 ).
According to the measurement, use the drill to drill identical holes of the appropriate size (use a
smaller drill bit than the actual screws) on the wall and ensure that it is level ( Figure 2 and 3 ). Screw
in the appropriate screws, either the 5 x 40 for wood walls or the 10 x 30 plus anchors for drywalls,
leaving enough space at the end to hang the casing ( Figure 4 ). To ensure that the screen is level,
use a leveler to check ( Figure 5 ).
Ceiling Mount
Using a tape measure, measure the distance between the two rings for hanging on the casing
( Figure 1 ). According to the measurement, use the drill to drill identical holes of the appropriate
size (use a smaller drill bit than the actual hook screws) on the ceiling and ensure that it is level
( Figure 2 and 3 ). Screw in the hook screws (not provided), and lift the screen into the hooks
screws to hang ( Figure 4 ). To ensure that the screen is level, use a leveler to check ( Figure 5 ).
A
A
1
2
3
4
5
The ceiling or wall for fixture installation must be secure to prevent the screens from falling.
While installing electrical motors, please hire professionals or our company to ensure safety.
A misconnection may lead to fire or leaks.
Keep all infrared wireless products away from fluorescent lighting as it may cause malfunctions.
Please read the following as any damage to the screen surface will affect the quality of the picture:
1.Avoid contact or touching the screen surface as it may cause scratches or tears.
2.Do not write or draw on the surface
3.Clean the screen with a soft cloth and luke warm water. Do not use any detergent or cleaning products.
Roll up the screen after every use. Ensure that the screen is level when installing; do not pull on the sides
or fold the screen.
To prevent unnecessary damage, the operating and maintenance of the screen should be done by adults.
used
Ignoring the safety warnings may
lead to injuries and/or damaging
the product.
Refrain from hanging anything on the
screen as it may cause the screen to
fall.
Do not connect any electrical
attachments or remote controls.
Fixtures should be installed in a secure
place to avoid accidents or the screen
falling.
Roll up the screen after every use.
Leaving it hanging for a long period
of time may cause the fabric to loosen.
Please contact our company for
repairs or maintenance. And if you
have any further questions.
Avoid taking apart the fixtures
yourself. Loose parts may cause
the screen to fall.
Warnings
Do not take apart and replace with unknown parts. If there are any problems, please contact our company.
Product specifications are subject to change.

34
Without mounting bracket installation
Wall mount
(Suitable for all sizes) Ceiling mount (Suitable for all sizes)
Hanger
Bracket Installation
To ensure extra durability and safety installation brackets have been included. The necessity of
brackets will vary depending on the location of installation. For installations of sizes up to 150",
use the C1 bracket. For installations of over 150", use C2.
Installation For Sizes Up to 150"
The screen can be installed either on the wall or with a hidden installation. The wall installation uses 2 holes
on the C1 brackets while the hidden installation uses all 3. Measure the distance between the holes that will
be used on the left and right brackets. Using the measured distance, drill the appropriate holes in the wall
( and ceiling if necessary ). Install the brackets, then lift and match up the screen's end caps to the brackets.
Insert the two screws to join the bracket and screen casing for both sides.
Installation For Sizes Over 150"
Using the C2 brackets, the screen can installed from the ceiling. Measure the distance between the holes
on the left and right brackets. Using the measured distance, drill the appropriate holes in the ceiling. Install
the brackets, then lift and match up the screen's end caps to the brackets. Insert the screws to join the
bracket and screen casing for both sides.
With mounting bracket installation( )Optional
Hidden installation
(Suitable for all sizes)
150 inches and under hidden
wall mount installation 150 inches and up installation
Instructions
To avoid overheating the motor, do not continually retract and lower the screen for over 4 minutes at a time.
If the motor overheats, it will need a cool down time of 2 minutes. The motor does not need any lubricants.
The drop and retract limit of the screen is factory preset to an optimal configuration. Please ask our company
or professional to adjust settings to avoid damaging the motor.
Drop Limit
Retraction Limit
Front view
SLIGHT UP
UP
STOP
DOWN
SLIGHT DOWN
Remote controller instruction:
1. To retract screen, press "UP".
2. To stop screen, press "STOP".
3. To lower screen down, press "DOWN".
4.
5.
To retract screen slightly, press "SLIGHT UP".
To lower screen down slightly, press "SLIGHT DOWN”.
Remote controller guideline:
1. Working temperature: -20 C - +80 C
0 0 .
2. Protection index: IP30.
3. Batteries: 1.5V x 2pcs, model # AAA.
4. Working under normal polluted environment.
5. Take out batteries if the controller will not be used for a long time.
6. Please change the batteries when signal is weak.
Back view
How to install the batteries:
Please change the batteries as below when signal is weak.
1. Turn around the controller, push to pen the cover as guiding arrow.
2. Put the batteries in according to the guide of anode and cathode.
3. Close the cover.
Caution
The controller does not work if mistaking the anode and cathode of
batteries, please correct the direction according to the figure on the
left.