Elite Screens VMAX2 (Plus) Series User manual

~
. - -------
!E
lte
~~~:::::.::::~
..... _ ... _---~
~~! !!!!!!~!1!!~
A PR(JJE~T TO\' .'>(Yr'EE\' C},lf?4 VJ
~
-t __ " .. iiiiiiii.ii __
1e
...... ·- · ......
~._ ~~
....... __ ...
~~------~
Ez-Electric Screen
Spectrurn/Vrnax2(Plus) Series
Type C- Ver. 1.2
Users Guide
www.elitescreens.com/[email protected]

a
·
--------
£lte
~~~::==~:~
---------
-_._-----
- --------
A PW'Jf;C7/0A SeRh!:l Cr),lw1N}
Important Safety and Warning Precautions
1. Be sure to read this manual before use and follow the procedures specified:
Put this manual at a safe place nearest to the device for reference.
Do not use the accessories not recommended by the manufacture to avoid any damage.
Handl.e the device carefully during transportation to avoid impact.
Do not putthe device at uneven or inclined places.
Do not put any heavy object on the power cord; fix the power cord properly to avoid
trippi ng over.
Do
not overload the power cord to prevent electrical shock or fire.
Guard any liquid or foreign object against entering the device, to avoid electrical shock or
fire due to loose contact or short circuit.
2.
If any accessory needs to be replaced, be careful to avoid short circuit.
3 There are no user serviceable accessories in the device. Nobody except authorized
technicians can open the device to avoid electrical shock. To prevent the risk of electrical
shockor fire, guard against moisture and rain shower.
Make
sure that the voltage connected to the product is correct at any time. The rating label on
the product indicates the rated voltage.
To protect the environment, send the product to the environment authority for disposal when it
cannot serve any longer.
Do
not handle the power plug when your hands are wet or your feet are in contact with water.
4. Do
not use the device at the following circumstances:
1) Disconnect the power cord under the condition of heavy storm, wind, rain, thunder 0
lightening.
2) Avoid direct sunshine, rain shower or moisture.
3) Keep away from fire sources and high temperature to prevent the device from being
overheated.
4)Cut off the power supply first before transportation or maintenance.
www.elitescreens.com/[email protected]

U
· -
-------
!E lteS~~EE~S
Accessory for Spectrum and VMAX2
Bubble level
IR
Battery
Wall box (Optional for Spectrum)
Eye recei ver (Optional for Spectrum)
A Built-In Receiver into Case, Please
always point to the eye receiver when
using the IR remote.
Red 12V Green OV
12V trigger cable (Optional for Spectrum)
Note: Contact your local reseller for optional accessory or
visit shop.elitescreens.com /www.vmaxscreens.com
for
accessorypurchase.
RF (Optional for Spectrum)
www.elitescreens.com/[email protected]

n
· - -------
-----_ ....
-..- .... _---
!E lte ~~~;;,;;,!!!~
VMAX2 &Spectrum Series
IMPORTANT SAFETY INSTRUCTIONS
1. Position the power cord so it will not be; near a hot area or hot surface
2. To avoid suffering an eelectric shock, do not attempt to disassemble this appliance yourself. In the event of
technical trouble, please contact Elite Screens service dept. for help with repairing your screen.
3. Please disconnect the power supply when screen is not in use for a long period of time as should be
done with any other electric household appliance.
4. To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is obvious
damage or the presence of broken parts.
PRE-INSTALLATION
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign particles
such as dust, sawdust and liquids.
Keyhole for flush mounting to
Wall
(R5MMR2MM)
Built-In IR Receiver -for
IR remote ( Point and Press
Up/Stop/Down)
4"
3-5/8" Hight of
end cap
Top
keyholes for ceiling
Mounting (R3MM,R2MM)
/
3-1/16"
3-1/8" Width of
end cap
o
www.elitescreens.com/[email protected]

A Pf,'O/h7'''W .YkFf. t r'OI!P1N)
INSTALLATION 1
1. Select the location for your screen within a reasonable angle of projection for your home
projector and access to a good power source.
2. For the best support of your screen, it is ideal to secure your screen into the studs of your
house's internal framework. If studs are not available, use hollow anchors for mounting
your wall-screws in drywall or if you are installing in a concrete structure, use the concrete
bolts for securing your screen into concrete walls. (Always Consult Installer or
hardware Store for the correct screws)
3. Make sure that the level in perfect horizontal alignment with one another. Use wall/ceiling
wood screws to secure to the wood studs. Use hollow wall anchors if mounting in drywall.
4. Position the washers to the head of the wall-screw. The washers give added stability b)
enabling to remain firmly anchored to the wall.
5. The screen casing is designed to accept the wall screws directly. If not using the Optional
L-bracket, be sure to position the washer between the head of the wall-screw and the
anchor slots on the projeCtor casing.
Regardless of mounting method, screen should be securely supported so that vibration or
even abusive pulling on the viewing surface will not cause case to work loose or fall.
Installer must insure that fasteners used are of adequate strength and suitable for the
mounting surface chosen.
www.elitescreens.com/[email protected]

n
· -
-------
!E
tte
~~~==~:~
---------
-_ .._--.-
- --------
A PkrJlf:C7 /()N L'ick'Hi: \. cnffP1.NY
Installation 2
1. Using a tape measure, mark the keyholes that are located at the back of the screen's case
end cap.
2.
After marking the area and predrilled hole, insert the screw and leave about 118"
of an inch from the wall to mount the screen. (Fig. 1)
ILoops I
~
Fig.2.
1. You can also hang the screen on a ceiling by using a chain with s-hooks (not included)
and hang it by the two loops located on each end ofthe case as shown on (Fig. 2).
\ :tional installation using achain to h7 screen from the ceiling.
[../
Fig.1
www.elitescreens.com/[email protected]

(1
' - -------
i£ lte
~~~::::~:~
... _------
-_ .. -----
- --------
A PRo/he7 fON SCRHh" t'.."rWPiJNJ
VMAX2/Spectrum optional accessories;
The L-Brackets for Wall & Ceiling
o
·1 __ 6_-_3_/4_"_Le_n_g_th __
r,---~--------~---,--- .~---_._--~._ .. - '--~-@J
Find the studs on your
wall or use drywall
anchors to install L
brackets to the desired
location
~
,---------------,
u
o
!1"Width
6-3/4"
Height
provided in conjunction with the wood screws
for dry wall installation as shown on Fig. I
Wood/Dry Wall installation: Use "B"
wood screws provided for installation on wood
studs on wall. Or use "E" hollow wall anchors
Fig. 1
I,,,
1"-'
'--
Top of "L"bracket from top view
II
©
Fig.2
Masonry/Cement wall
installation: Use "0" bolts
provided
for installing your
screen on a cement wall as
shown on Fig. 2.
t\?
) I
1JJJ
I:r:fWAL~
'--------
*Once the L-brackets are in place, the screen can be hung from the vertical hooks.
Please note these are only examples and additional hardware may be required for your particulal
installation. Also, the screen can be hung directly on the wall screws or bolts
without using the L-brackets at all.
www.elitescreens.com/[email protected]

U
·
--------
!E
lte
~~~==~:~
--------
-_ .. __ ..-
---------
OPERATION
IR
ideo Projection Interface
12-Volt Trigger Assembly
Ri?1 Connection pins
ltJllnside
Diagram B
Infrared "Eye"
Sensor with
IR
Remote Control
.§J
Transmitter
~ Connection pins
~~de
To Projector
Red DC+12V[
Green OV
~Bubble Level
~
~ i
<:::> Wall-mounted Receiver
(Extension Sensor)
Diagram A
Transmitter Wall Box with IR Remote Control
Connection pins
inside of case
1. Bubble Level: Included with the installation
package is asmall bubble level that can be useful in
determini ng ifthe screen is perfectly level when
installing.
12VTrigger
The VMAX2 and Spectrum Screens have the capability of using a 12- Volt
Trigger. This accessory is optional for Spectrum Screens and can be
purchased separately.
~~
2. Below is the RF remote with arange of 30 F
3. Below is the IR remote (Infra Red)
with arange of 15 Ft.
(Radio Frequency)
Note: When you get the optional RF, you
Should
follow the instruction and adjust
the code.
(Infrared)
Note:
The light on this remote does not turn on
when the
buttons are depressed unlike the RF.
Radio Frequency Remote Control
Infrared Remote Control
www.elitescreens.com/[email protected]

U
·--------
.. _--_ ....
-._- ... _----
rr Ite~:..:':==~~
"-£", ---------
Note:
If the electric screen does not move, please check the following:
1. Check the power supply and fuse first. The screen will not move without power.
2.
Make sure the power cord is plugged to the power outlet.
3. Check all cable connections to see any are disconnected.
4. If the screen works well with the line switch but not with the remote control, make sure
that the remote has good batteries in it.
FAQ's
1. Q: How is the Matte White or High Contrast screen material cleaned?
A: The Matte White or Elite High Contrast screen material can be cleaned with mild
soap and water.
2. Q: What type of batteries do the remote controls require?
A: The IR and RF remote controls use AAA alkaline batteries.
3. Q: Can you manually pull down the screen?
A: No, manually pulling down the screen will damage the electronic motor rolling system
4. Q: How do Remote control work with other brand Universal Remote?
A: Remote Control Code of Spectrum and VMAX2 are as following, please contact your other
brand universal remote for more detail after providing them Spectrum and VMAX2 code.
For Spectrum, VMAX2 (Plus), Home2(3) and Tension2(3) Series
Up:
1111 0000 0001
Stop:1111 0000 0010
Down:1111 0000 0100
5. Q:
What is the gain on the matte white screen material?
A: The matte white material has a gain of 1.1 , detail spec. info, please
check our web-site for more detail.
Note: For more Update FAQ, please visit www.elitescreens.com
www.elitescreens.com/[email protected]

n
· - -------
£
ttie
~~~:::::::':~
---------
-_ .. _-_.-
- --------
Warranty Policy - Electric Screens
• One (1) year warranty parts and labor from purchase date as fo llows (except for
refurbished units as specified below):
•
Refurbished units carry a 90-day parts and labor warranty.
•
Demo units or open box items are AS IS items and do not carry awarranty.
•
Each party will be responsible for one way shipping during the warranty period.
• DOA (Defective On Arrival): Must be reported within 7 business days of receipt. A RMA
(Return Merchandise Aauthorization) number must be issued in order to process a replacement.
Elite Screens will replace the DOA (Defective On Arrival) unit with a brand new replacement
(see exceptions below) after the DOA unit is received and/or confirmed defective.
Once the product is received, Elite Screens will send out a new unit to the customer by
ground service (subject to inventory availability).
Should a problem be reported after the 7-day grace period, the item must be shipped to us
for
warranty repair.
Missing Parts must be reported within the 7-day (DOA) grace period.
•
Ifreported after 7days, customer will be only responsible for shipping and handling fees. If
reported after30 days of receipt, customer is responsible for cost of the parts and shipping & handli
n
fees.
Please visit link below for full warranty information
Http://www.elitescreens.com/service.htm
Please visit link below for warranty claim
Http://www.elitescreens.com/serviceform.htm
*A new or refurbished replacement will be sent out to the customer depending on the
type of purchase (new or refurbished) or based on stock availability.
www.elitescreens.com/[email protected]