Montigo D3615 Instruction Manual

XG0222
Installation & Maintenance Manual
• Theinstallationofthisreplacemustbedonebya
qualiedandcertiedgasapplianceinstaller.
• Checklocalcodesandreadallinstructionspriorto
installation.
®
C
US
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury,
death, or property damage.
—Donotstoreorusegasolineorotherammablevaporsand
liquidsinthevicinityofthisoranyotherappliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phoneinyourbuilding.
• Leavethebuildingimmediately.
• Immediatelycallyourgassupplierfromaneighbour's
phone. Follow the gas supplier’s instructions.
• Ifyoucannotreachyourgassupplier,callthere
department.
—Installationandservicemustbeperformedbyaqualied
installer,serviceagencyorthegastter.
Distinction INDOOR GAS FIREPLACE
D3615, D3615ST
Natural Gas or Propane Gas
D4815, D4815ST
Natural Gas or Propane Gas
D7215, D7215ST
Natural Gas or Propane Gas
Label all wires prior to disconnection when servicing controls.
Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing
Installation and service must be performed by a qualied installer,
service agency or the gas tter.
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
NOTICE
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
WARNING

XG02222
General
Congratulations on your purchase of a Montigo Fireplace.
With over 30 years of experience, Montigo is committed to providing
you with a gas fireplace that is not only a beautiful addition to your
space, but that is also designed and manufactured to the highest
safety, reliability and engineering standards.
We strongly encourage you to read and carefully follow the
instructions laid out in this Installation, Operation and Maintenance
Manual and retain it for your future reference. Pay special attention
to all cautions, warnings, and notices throughout this manual
intended to ensure your safety.
This manual covers installation, operation and maintenance. Lighting,
operation and care of this replace can be easily performed by the
homeowner. All installation and service work should be performed
by a qualied or licensed installer, plumber or gas tter as certied
by the state, province, region or governing body where the replace
is being installed.
This installation, operation and maintenance manual is applicable
to the models described in Table 1. Refer to your rating plate to
verify included options.
Warranty and Installation Information: (See Appendix B)
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
• Modication of the replace and/or components including Direct-
Vent assembly or glass doors.
• Use of any component part not manufactured or approved by
Montigo in combination with this Montigo replace system.
• Installation other than as instructed in this manual.
• Consult your local Gas Inspection Branch on installation
requirements for factory-built gas replaces. Installation & repairs
should be done by a qualied contractor.
Introduction
Safety Alert Key
Young children should be carefully supervised when they are in the
same room as the appliance. Toddlers, young children, and others
may be susceptible to accidental contact burns. A physical barrier is
recommended if there are at-risk individuals in the house. To restrict
access to a replace or stove, install an adjustable safety gate to keep
toddlers, young children, and other at-risk individuals out of the room
and away from hot surfaces
CAUTION
Indicates a hazardous situation which, if
not avoided, WILL result in death or serious
injury or property damage.
Indicates a hazardous situation which, if not
avoided, WILL result in minor or moderate
injury.
Indicates a hazardous situation which, if not
avoided, COULD result in death or serious
injury or property damage.
Indicates practices that are important, but
not related to personal injury.
DANGER
CAUTION
WARNING
NOTICE

XG0222 3
General
Contents
Safety Alert Key....................................................................................................................... 2
Introduction ............................................................................................................................ 2
Section A: Before You Begin .................................................................................................... 4
Installation Checklist ................................................................................................................. 4
Standard Installation Checklist ................................................................................................ 5
Rating Plate Sample .................................................................................................................. 6
Section 1: Product Dimensions.............................................................................................. 7
Section 2: Framing .................................................................................................................. 8
Clearances.................................................................................................................................. 8
Assemble Non Combustible Framing ..................................................................................... 8
Framing the Single Sided Fireplace ......................................................................................... 9
Framing the See-Through Fireplace........................................................................................ 9
Chase venting...........................................................................................................................10
TV recess framing.................................................................................................................... 10
Framing with Cool Wall Advantage .......................................................................................11
Framing with Cool Wall Advantage Sidewall kits .................................................................12
Section 3: Venting ................................................................................................................. 13
Restrictor plate Installation.................................................................................................... 13
Section 3-3-1: Venting Layouts ........................................................................................... 14
Vertical Termination................................................................................................................14
Vertical Termination - 2 Elbows .............................................................................................14
Vertical Termination - 3 Elbows .............................................................................................15
Horizontal Termination - 1 Elbow.......................................................................................... 15
Horizontal Termination - 2 Elbows........................................................................................ 16
Horizontal Termination - 3 Elbows........................................................................................ 16
Section 3-2: Installing a Roof Mounted Direct Vent Termination (PVTK1SS) ................ 17
Section 3-2-1: Venting Layout ................................................................................................17
Section 3-3: Installing a Wall Mounted Direct Vent Termination.................................... 18
Section 3-3-2: Venting Components......................................................................................19
Section 3-3-2.2: Simpson Duravent Venting Components ................................................. 20
Section 3-3-2.3: ICC Venting Components*.......................................................................... 21
Section 3-3-2.4: Metalfab Venting Components*................................................................21
Section 3-5: Heat Shields ...................................................................................................... 22
PropaneConversion ............................................................................................................. 24
Section 4: Wiring ................................................................................................................... 26
Distinction (N/L) I-2 Wiring Diagram .....................................................................................26
Installation of Electrical Supply.............................................................................................. 26
CPI[ContinuousPilotIgnition]/IPI[IntermittentPilotIgnition]JumperCable
Installation ............................................................................................................................ 27
“Why use CPI mode”? ..............................................................................................................27
The difference between IPI and CPI: ..................................................................................... 27
Installing the CPI Jumper Cable .............................................................................................27
Section 5: Installing the gas line.......................................................................................... 28
Fuel Type .................................................................................................................................. 28
Gas Pressure ............................................................................................................................28
Gas Connection........................................................................................................................28
Mantels & Surrounds.............................................................................................................. 29
Finishing Around the Fireplace.............................................................................................. 29
Sidewall clearances .................................................................................................................29
Section8:Removing&InstallingtheScreen/Door ......................................................... 30
Removing the Screen ..............................................................................................................30
Reinstalling the Screen ...........................................................................................................30
Removing the door.................................................................................................................. 30
Reinstalling the door...............................................................................................................30
Section 9: Installing the Media ............................................................................................. 31
Firestone & Fireglass Quantity............................................................................................... 31
Optional speckled stones ...................................................................................................... 31
Optional Driftwood Logset..................................................................................................... 31
Log Kit Installation................................................................................................................... 31
D3615 Single Sided Driftwood Kit.......................................................................................... 32
D3615ST See Through Driftwood Kit .................................................................................... 32
D4815 Single Sided Driftwood Kit.......................................................................................... 33
D4815ST See Through Driftwood Kit .................................................................................... 33
D7215 Single Sided Driftwood Kit Step 1.............................................................................. 34
D7215 Single Sided Driftwood Kit Step 2.............................................................................. 34
D7215 See-Through Driftwood Kit ........................................................................................ 35
Distinction (N/L) I-2 Wiring Diagram ..................................................................................... 36
LED Strip Instructions ............................................................................................................. 38
Before you begin ..................................................................................................................... 39
Installation................................................................................................................................ 39
Before you begin ..................................................................................................................... 41
Section 7: Finishing the fireplace......................................................................................... 43
Cement Board Install .............................................................................................................. 43
Remote Operation .................................................................................................................44
Initializing the System for the first time................................................................................ 45
Operating the System for the first time................................................................................ 45
Temperature Indication Display ............................................................................................ 45
Turn On the Fireplace ............................................................................................................. 45
Turn Off the Fireplace............................................................................................................. 45
Remote-Flame Control............................................................................................................ 46
Room Thermostat (Remote Control Operation).................................................................. 46
Smart Thermostat
(Remote Control Operation) .................................................................................................. 46
Disabling Thermostat.............................................................................................................. 47
Fan Speed Control................................................................................................................... 47
Accent Light Control................................................................................................................ 47
LED Remote Control Operation............................................................................................48
Pairing the remote to the module (Code Clearing and Code Matching) .......................... 48
Section 10: Cleaning and Maintenance ..............................................................................49
General ..................................................................................................................................... 49
Cleaning.................................................................................................................................... 49
Appendix A: Venting Terminations......................................................................................50
Appendix B: Warranty ........................................................................................................... 51
Appendix B: Warranty Continued ........................................................................................52
Appendix C: Amendment ......................................................................................................53

XG02224
General
IMPORTANT MESSAGE: SAVE THESE INSTRUCTIONS
The Distinction Series replaces must be installed in accordance with
these instructions. Carefully read all the instructions in this manual
rst. Consult the Local Gas Branch to determine the need for a permit
prior to starting the installation. It is the responsibility of the installer to
ensure this replace is installed in compliance with the manufacturers
instructions and all applicable codes.
Installation Checklist
• Determine the desired install location of your replace.
• See Section 1, Dimensions on Page 8, and refer to the Framing
Section 2 for details.
• Select the location of your termination and resulting vent run.
• Your selected termination location must be the highest point in the
Direct Vent installation.
• Should it be impossible to meet the venting requirements laid out
in Section 3: Venting, please contact your Montigo dealer regarding
the use of a Montigo Power Vent.
• Lay out the Vent run; calculating the required elbows and straight
runs of 5"/8" ex and/or rigid pipe.
• Layout Electrical Requirements refer to Section 4: Wiring, for Details.
• Refer to Section 5: Installing the Gas Line, for details on the gas
connection and access.
• Refer to local codes and guidelines for installation requirements.
• Installation and repairs should be done by a qualied contractor
and must conform to:
• Installations in Canada must conform to the local codes or in the
absence of local codes to the current version of Natural Gas and
Propane Installation Code, CSA B149. Electrical installations must
conform to the local codes or, in the absence of local codes, to the
current version of Canadian Electrical Code, CSA C22.1.1
• Installations in the USA must conform to the local codes or in the
absence of local codes to the current version of National Fuel Gas
Code, ANSI Z223.1/NFPA 54. Electrical installations must conform
to the local codes or, in the absence of local codes, to the current
version of the National Electrical Code, ANSI/NFPA 70. See Appendix
C for installation within the State of Massachusetts
Do not use this appliance if any part has been under water.
Immediately call a qualied service technician to inspect the appliance
and to replace any part of the control system and any gas control that
has been under water
Due to high temperatures, the appliance should be located out of
trac and away from furniture and draperies
Children and adults should be alerted to the hazards of high surface
temperature and should stay away to avoid burns or clothing ignition
A barrier designed to reduce the risk of burns from the hot viewing
glass is provided with this appliance and shall be installed for the
protection of children and other at-risk individuals
Clothing or other ammable material should not be placed on or near
the appliance
Installation and repair should be done by a qualied service person.
The appliance should be inspected before use and at least annually
by a professional service person. More frequent cleaning might be
required due to excessive lint from carpeting, bedding material, etc. It
is imperative that control compartments, burners, and circulating air
passageways of the appliance be kept clean
NOTICE
NOTICE
NOTICE
NOTICE NOTICE
NOTICE
Section A: Before You Begin

XG0222 5
General
Standard Installation Checklist
This standard installation checklist is to be used by the installer in conjunction with, not instead of, the instructions contained within this
installation manual.
Customer Date Installed:
Install Address: Location of Fireplace:
Installer:
Model (circle one): D3615, D3615ST, D4815, D4815ST, D7215, D7215ST Dealer Phone:
Serial #:
*Only applicable for DL Series
YES NO IF NO, WHY NOT?
Appliance Install: Section 2
Framing complies with install manual.
Standos have been installed.
Proper clearances have been maintained.
Venting: Section 3
Venting conguration complies with vent diagrams.
Venting installed, fastened, and secured in place maintaining proper clearance.
Firestops installed.
Exterior wall/roof ashing installed and sealed in compliance with local building code.
Terminations installed and sealed in compliance with local building code.
Direct vent termination is highest point in vent assembly.
Wiring/Electrical: Section 4
Unswitched power provided to the appliance PPO box.
Low voltage wire connected to dry contact wall switch (non-powered)*
Gas: Section 5
Proper appliance for fuel type.
Was a conversion performed?
Leak check performed & inlet pressure veried.
Finishing: Section 6
Only non-combustible materials installed in non-combustible areas.
Clearances meet installation manual requirements
Mantels and/or projections comply with install manual
Appliance Setup: Section 7 through 9
Media, door, and screen installed according to install manual
Manual given to home owner.
Started appliance and veried no gas leaks exist.
Comments:

XG02226
General
Rating Plate Sample
Figure 1 Rating Plate for D7215 Figure 1.b Rating Plate for D7215ST



 








 


LBA120x Distinction Series no CSA Nov7,2016
  










  

    





 

¡¢¡  








£ ¤¥   
¦
¡
¦
¡

¥
¥ 
¡ ¡
 

¡¡
 


57,000
57,000
39,000
46,000
24 DMS / N/A
2.25 mm / N/A
3.5" W.C.
10" W.C.
5.5" W.C.
13" W.C.
4.0"
0.5"
48"
N/A
N/A
0"
16"
N/A
N/C
D7215NI-2
N/A
N/A



 








 


LBA120x Distinction Series no CSA Nov7,2016
  










  

    





 

¡¢¡  








£ ¤¥   
¦
¡
¦
¡

¥
¥ 
¡ ¡
 

¡¡
 


4.0"
0.5"
N/A
N/A
0"
16"
N/A
N/C
D7215STNI-2
57,000
57,000
39,000
46,000
N/A
N/A
24 DMS / N/A
2.25 mm / N/A
3.5" W.C.
10" W.C.
5.5" W.C.
13" W.C.

XG0222 7
General
Figure 2. Distinction Fireplace dimensions (Tolerance ± ⅛"). Figure 2.b Distinction Fireplace dimensions (Tolerance ± ⅛").
Section 1: Product Dimensions
SINGLE SIDED SEE THROUGH
D4815 SINGLE SIDED DIMENSIONS
A B C D E F G H I J K L
63⁄ 17⁄ 52⁄ 71¾ 49⁄ 17 15 6⁄ 2⁄ 13⁄  10⁄ 41
D4815 SEE THROUGH DIMENSIONS
A B C D E F G H I J K L
63⁄ 17⁄ 52⁄ 71¾ 49⁄ 17 15 5½ 2⁄ 13⁄  10 ⁄ 40⁄
D3615 SINGLE SIDED DIMENSIONS
A B C D E F G H I J K L
51⁄ 17⁄ 40¾ N ⁄A 37⁄ 17 15½ 6⁄ 2⁄ 13⁄  10⁄ 41
D3615 SEE THROUGH DIMENSIONS
A B C D E F G H I J K L
51⁄ 17¾ 40¾ 59¾ 37⁄ 17 15½8⁄ 2⁄ 13⁄ 10⁄ 41
D7215 SINGLE SIDED DIMENSIONS
A B C D E F G H I J K L
87⁄ 18⁄ 76¾ 95⁄ 73⁄ 17 15½ 5½ 2⁄ 13 ⁄ 10 ⁄ 41
D7215 SEE THROUGH DIMENSIONS
A B C D E F G H I J K L
87⁄ 17¾ 76¾ 95⁄ 73⁄ 17 15½ 5½ 2⁄ 13⁄ 10 ⁄ 41
A A
B B
C C
C C
D D
G G
H H
J J
I I
K K
L LF F
F F
E E

XG02228
Installation
NOTE: When constructing the framed opening, please ensure there is
access to install the gas line when the unit is installed.
Clearances
To ensure the replace operates safely, all models must maintain
the following clearances:
MODEL Top Sides Floor Back Base of unit to ceiling †
D3615 8⁄'' 4'' 0'' .5'' 89''
D3615ST 8⁄'' 4'' 0'' N/A 89''
D4815 8⁄'' 4'' 0'' .5'' 89''
D4815ST 8⁄'' 4'' 0'' N/A 89''
D7215 18⁄'' 4'' 0'' .5'' 89''
D7215ST 18⁄'' 4'' 0'' N/A 89''
† Note: If measuring from bottom edge of concrete board to ceiling,
minimum clearance is 92¼.
Unprotected combustible walls which are perpendicular to the replace
opening must maintain 6" clearance.
Section 2: Framing
Clearances must be in accordance with local installation codes and
the requirements of the gas supplier
Figure 3. Combustible Clearances
When this appliance is installed directly on ANY combustible other
than wood ooring (carpet, vinyl, etc.). It must be installed on an
equivalent wood or metal panel. This material must extend the full
width and depth of the appliance.
WARNING
NOTICE
Framing measurement includes 2¼" platform to avoid driving screws
into important components inside the replace box.
NOTICE
AssembleNonCombustibleFraming
Figure 8. Assembly of Non Combustible Framing
2432
95 3
4"
391
15 3
8"
1215
47 13
16 "
1215
47 13
16 "
467
18 3
8"
1:24
DWG. NO.
SHEET 1 OF 2
WEIGHT:
DL72ST-No Combustible Framing Assembly
Finish
MATERIAL
Revision / Date
Drawn by
DATE
NAME
27/02/2018
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DL72ST\Cad Drawings\DL72ST-No Combustible Framing Assembly
April-30-18 9:40:32 AM
SCALE
DM
Description
DL72ST-Non Combustible Framing
Revision
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
2
3
1
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
ITEM NO. PART NUMBER DESCRIPTION QTY. REVISION
1 DL72097-20
Non-Combustible stud,
Horizontal
2 B
2 DL72098-20
DL72-Non-Combustible stud,
Vertical
2 A
3 DL72099-20
DL72-Non-Combustible Stud
Connector
1 A
1:24
DWG. NO.
SHEET 2 OF 2
WEIGHT:
DL72ST-No Combustible Framing Assembly
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
27/02/2018
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\DL72ST\Cad Drawings\DL72ST-No Combustible Framing Assembly
April-30-18 9:40:32 AM
SCALE
DM
Description
DL72ST-Non Combustible Framing
Revision
Dimentions
A15 ⅜
B18 ⅜
C 47 13/16
D95 ¾
D
C C
B
A

XG0222 9
Installation
Framing the Single Sided Fireplace Framing the See-Through Fireplace
E
A
B
D
1
3
2
C
E
C
A
B
D
1
2
3
206
81
8"
1680
66 1
8"
206
81
8"
625
24 5
8"
419
16 1
2"
330
13"
1375
54 1
8"
FFG
I
K
H
J
4
206
81
8"
1680
66 1
8"
206
81
8"
625
24 5
8"
419
16 1
2"
330
13"
1375
54 1
8"
FFG
I
K
H
J
4
D4815 SINGLE SIDED DIMENSIONS
A B C D E F G H I J K
49⁄ 2¼ N/A 71¾ 17½10⁄ 52⁄ 24 17⁄  12⁄   53⁄
D7215 SINGLE SIDED DIMENSIONS
A B C D E F G H I J K
59⁄ 2¼ 41⁄  95¾ 18½10⁄ 76⁄ 33⁄ 17 ⁄ 12⁄ 63⁄
D3615 SINGLE SIDED DIMENSIONS
A B C D E F G H I J K
49⁄ 2¼ N/A 59¾ 17½10⁄ 40⁄ 24 17 ⁄  12⁄ 53⁄
D4815 SEE THROUGH DIMENSIONS
A B C D E F G H I J K
49⁄ 2¼ N/A 71¾ 17  ⁄  10⁄ 52⁄ 24 17 ⁄  12⁄ 53⁄
D7215 SEE THROUGH DIMENSIONS
A B C D E F G H I J K
59⁄ 2¼ 41⁄  95¾ 17 ⁄ 10⁄ 76⁄ 33⁄ 17  ⁄ 12 ⁄ 63⁄
D3615 SEE THROUGH DIMENSIONS
A B C D E F G H I J K
49⁄ 2¼ N/A 59¾ 17 ⁄ 10⁄ 40⁄ 24 17⁄  12⁄ 53⁄
1Floor structure
2Non-combustible metal framing
(not used on 36, 48)
3Fireplace platform
4Concrete board

XG022210
Installation
Chaseventing
At a minimum, a 120"2 opening is required in the nished enclosure to
keep temperatures within a safe level. This can be achieved in a variety
of ways such as the few shown below.
The opening of the chase cannot be lower than 3" from the top of the
enclosure to prevent heat from pocketing at the top of the enclosure.
A minimum of 2" from the top of a chase vent to the ceiling is needed.
Any combination of the above examples is an acceptable chase vent
providing they add up to 120"2
Figure 19.b Side chase venting (6"x10") on
both sides of enclosure
Figure 19.d Front chase venting (2"x60")
on front of enclosure
Figure 19.d Open top chase venting on
top of enclosure
Figure 19.c Top chase venting (3"x40") on
top of enclosure
TV recess framing
Figure 8.b.d Cool Wall Advantage TV recess dimensions
The recess must be made from Non-Combustable materials. Recess can
be increased beyond a 4" depth by using a 45° or 90° elbow in venting
after the minimum 3' upward distance is achieved, 1" clearance from
venting to combustibles must still be maintained.
4" Max
Depth
The recess MUST
be made from
Non-Combustable
materials. Maintain
1" clearance
from venting to
combustibles.
13 5/8" min. from
replace opening
Minimum
2" gap
3" Min. from
ceiling
TV RECESS
Ceiling

XG0222 11
Installation
FramingwithCoolWallAdvantage
Figure 8.b.b Framing with Cool Wall Advantage
Below are basic instructions on the framing of the Cool Wall advantage kit. More detailed instructions including the installation diagrams are
included with the kit.
1/32
.015
.005
1
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
DIM ARE IN INCHES
FRACTIONAL
X.XX
X.XXX
ANGULAR:
NAME
CHECKED
DRAWN
THIRD ANGLE PROJECTION
DATE
FINISH
MATERIAL
WEIGHT (lbs)
BEND ALLOW.
K-FACTOR
38" Min
To Cool Wall
3" min
to Ceiling
2015.73
79.4
Steel Studs
2x4 On Edge
5" Dia Flex Vent
Main Vent
1:32
DWG. NO. REV.
1 OF 2
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
July-25-17 10:30:24 AM
SCALE:
TV Kit Framing
SHEET:
SIZE
CF 26/05/2017
CF
1/19/2017
Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\Manual\Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\Distinction SHow Unit\TV Kit Framing
1/32
.015
.005
1
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
DIM ARE IN INCHES
FRACTIONAL
X.XX
X.XXX
ANGULAR:
NAME
CHECKED
DRAWN
THIRD ANGLE PROJECTION
DATE
FINISH
MATERIAL
WEIGHT (lbs)
BEND ALLOW.
K-FACTOR
38" Min
To Cool Wall
3" min
to Ceiling
2015.73
79.4
Steel Studs
2x4 On Edge
5" Dia Flex Vent
Main Vent
1:32
DWG. NO. REV.
1 OF 2
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
July-25-17 10:30:24 AM
SCALE:
TV Kit Framing
SHEET:
SIZE
CF 26/05/2017
CF
1/19/2017
Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\Manual\Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\Distinction SHow Unit\TV Kit Framing
1/32
.015
.005
1
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
DIM ARE IN INCHES
FRACTIONAL
X.XX
X.XXX
ANGULAR:
NAME
CHECKED
DRAWN
THIRD ANGLE PROJECTION
DATE
FINISH
MATERIAL
WEIGHT (lbs)
BEND ALLOW.
K-FACTOR
38" Min
To Cool Wall
3" min
to Ceiling
2015.73
79.4
Steel Studs
2x4 On Edge
5" Dia Flex Vent
Main Vent
1:32
DWG. NO. REV.
1 OF 2
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
July-25-17 10:30:24 AM
SCALE:
TV Kit Framing
SHEET:
SIZE
CF 26/05/2017
CF
1/19/2017
Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\Manual\Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\Distinction SHow Unit\TV Kit Framing
1/32
.015
.005
1
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
DIM ARE IN INCHES
FRACTIONAL
X.XX
X.XXX
ANGULAR:
NAME
CHECKED
DRAWN
THIRD ANGLE PROJECTION
DATE
FINISH
MATERIAL
WEIGHT (lbs)
BEND ALLOW.
K-FACTOR
76mm
3"
Standoff
38mm
11
2
"
Standoff
52mm
2"
Opening
1653mm
65 1
16
"
Opening
778mm
30 5
8
"
Approximate Dimension
1677.92mm
66 1
16
"
5" Flex Vent Collars
Stabilizers
160mm
65
16
"
531mm
20 15
16
"
236mm
95
16
"
12.7mm
1 2
"
1:16
DWG. NO.
REV.
1 OF 2
A
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
June-21-18 12:25:45 PM
SCALE:
DL63 Heat Distribution TV Kit
DL63-Heat distribution TV kit
SHEET:
SIZE
A
CF 26/05/2017
CF
1/19/2017
Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\Manual\Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\DL63-Heat distribution TV kit for manual
1/32
.015
.005
1
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
DIM ARE IN INCHES
FRACTIONAL
X.XX
X.XXX
ANGULAR:
NAME
CHECKED
DRAWN
THIRD ANGLE PROJECTION
DATE
FINISH
MATERIAL
WEIGHT (lbs)
BEND ALLOW.
K-FACTOR
76mm
3"
Standoff
38mm
11
2
"
Standoff
52mm
2"
Opening
1653mm
65 1
16
"
Opening
778mm
30 5
8
"
Approximate Dimension
1677.92mm
66 1
16
"
5" Flex Vent Collars
Stabilizers
160mm
65
16
"
531mm
20 15
16
"
236mm
95
16
"
12.7mm
1 2
"
1:16
DWG. NO.
REV.
1 OF 2
A
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
June-21-18 12:25:45 PM
SCALE:
DL63 Heat Distribution TV Kit
DL63-Heat distribution TV kit
SHEET:
SIZE
A
CF 26/05/2017
CF
1/19/2017
Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\Manual\Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\DL63-Heat distribution TV kit for manual
1/32
.015
.005
1
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
DIM ARE IN INCHES
FRACTIONAL
X.XX
X.XXX
ANGULAR:
NAME
CHECKED
DRAWN
THIRD ANGLE PROJECTION
DATE
FINISH
MATERIAL
WEIGHT (lbs)
BEND ALLOW.
K-FACTOR
76mm
3"
Standoff
38mm
11
2
"
Standoff
52mm
2"
Opening
1653mm
65 1
16
"
Opening
778mm
30 5
8
"
Approximate Dimension
1677.92mm
66 1
16
"
5" Flex Vent Collars
Stabilizers
160mm
65
16
"
531mm
20 15
16
"
236mm
95
16
"
12.7mm
1 2
"
1:16
DWG. NO.
REV.
1 OF 2
A
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
June-21-18 12:25:45 PM
SCALE:
DL63 Heat Distribution TV Kit
DL63-Heat distribution TV kit
SHEET:
SIZE
A
CF 26/05/2017
CF
1/19/2017
Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\Manual\Y:\Products\Residential Products\R&D Projects\DL63\Cad Drawings\DL63-Heat distribution TV kit for manual
HDKPD** DIMENSIONS
A B C D E F G H I J
36" ½" 39⁄"38⁄"3" 1½" N/A 2" 9⁄"N/A 7⁄"
48" ½" 51⁄"50⁄"3" 1½" 30½"2" 9⁄"21"7⁄"
72" ½" 75⁄"74⁄"3" 1½" 39⁄"2" 9⁄"21"7⁄"
AB
C
D
E
F
G
H
I
J
On 72" TV kit, the top ange is attached to
the back of the top 2x4

XG022212
General
Figure 8.c.c Cool Wall Advantage Sidewall Vertical vent dimensions Figure 8.c.c Cool Wall Advantage Sidewall Plenum dimensions
Figure 8.c.d Cool Wall Advantage Sidewall Horizontal vent dimensions
FramingwithCoolWallAdvantageSidewallkits
400
15.748
200
7.874
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
1:8
DWG. NO.
SHEET 1 OF 1
WEIGHT:
GR0004
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
05/05/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\Distinction Accessories\Heat Distribution Channel\GR0004
October-03-18 2:17:57 PM
SCALE
DM
Description
GRSDV - Sidewall Cavity Venting Louver Vertical
A
Revision
400
15.748
200
7.874
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
1:8
DWG. NO.
SHEET 1 OF 1
WEIGHT:
GR0003
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
05/05/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\Distinction Accessories\Heat Distribution Channel\GR0003
September-19-18 11:12:13 AM
SCALE
DM
Description
GRSDH - Sidewall Cavity Venting Louver Horizontal
A
Revision
400
15.748
200
7.874
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
1:8
DWG. NO.
SHEET 1 OF 1
WEIGHT:
GR0003
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
05/05/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\Distinction Accessories\Heat Distribution Channel\GR0003
September-19-18 11:12:13 AM
SCALE
DM
Description
GRSDH - Sidewall Cavity Venting Louver Horizontal
A
Revision
18.812
10.942
15.884
REVISIONS
REV. DESCRIPTION DATE CHANGED BY
- . - -
1:8
DWG. NO.
SHEET 2 OF 2
WEIGHT:
HDC16-Cool Wall Discharge Kit
Finish
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ANGULAR
.5
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
Revision / Date
Drawn by
DATE
NAME
17/10/2018
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Y:\Products\Residential Products\R&D Projects\Distinction Accessories\Heat Distribution Channel\HDC16-Cool Wall Discharge Kit
October-18-18 9:37:58 AM
SCALE
DM
Description
HDC16-Cool Wall Discharge Kit
Revision

XG0222 13
Installation
Figure 8.b.b Included Restrictor plates
Figure 8.b.c Restrictor plate Installation
Restrictor plate Installation
Under no circumstances can Montigo ex venting be cut to
accommodate an installation. Use an alternative length to complete
your vent run.
NOTICE
Section 3: Venting
The termination location MUST be selected such that it is the highest
point in the venting assembly. It should also be selected such that it
provides the shortestvent run possible. Should it beimpossible to ensure
that the termination is the highest point or should it be impossible to
meet the venting guidelines laid out below please contact your Montigo
dealer to discuss power venting options.
Notes For Planning Venting: Included Restrictor plates:
1" Bae
1.5" Bae
1.75" Bae
The distinction is supplied with 3 dierent sized restrictor plates to
improve ame eciency. The size of restrictor used largely depends
on the number of elbows used in the vent run, as well as vertical rise.
Lengthy vertical runs without elbows would generally require the 1.75''
restrictor. Shorter runs, or multi elbow installations would use the 1.5''
or the 1'' restrictor.
• Venting originates from the top of the unit.
• Venting can terminate through the roof or exterior wall.
• For a detailed diagram of allowed termination locations, see
Appendix A.
• Once the termination location has been established refer to the
appropriate section for installation details.
• For Heat Shield requirements see Section 3-3-3.

XG022214
Installation
Vertical Termination - 2 Elbows
Vertical Termination VerticalTermination-2Elbows
Vertical Termination
Figure 8. Vertical Termination Figure 8.b Vertical Termination - 2 Elbows
*Restrictor may be required
If the vent rise is over 8ft straight vertical, a restrictor must be installed.
We recommend using the 1.75” wide restrictor. If 1.75'' is too restrictive,
a 1.5'' and 1'' restrictor is also supplied.
NOTE: If using a restrictor, use an IR gun to measure the glass
temperature after 1 hour of running, and ensure the glass temperature
does not exceed 470°F and ensure that none of the media and no part
of the door has discoloured.
*Minimum 36'' from top of unit before attaching an elbow
V1
V1
H1
V2
Section 3-3-1: Venting Layouts
D3615, D3615ST, D4215, D4215ST, D7215, D7215ST
Vertical Minimum V1+V2 3' 4' 5' 6' 7' 8' 9' 10'
Horizontal Maximum H1 2' 6' 10' 12' 15' 18' 21' 24'
D3615, D3615ST, D4215, D4215ST, D7215, D7215ST
Vertical Minimum 3'
Vertical Maximum 32'

XG0222 15
Installation
VerticalTermination-3Elbows
Figure 8.c Vertical Termination - 3 Elbows Figure 8.d Horizontal Termination - 1 Elbow
*Minimum 36'' from top of unit before attaching an elbow *Minimum 36'' from top of unit before attaching an elbow
Horizontal Termination - 1 Elbow
Vertical Termination - 3 Elbows
V1
V1
V2
H1
H1
H2
HorizontalTermination-1Elbow
D3615, D3615ST, D4215, D4215ST, D7215, D7215ST
Vertical Minimum V1+V2 3' 4' 5' 6' 7' 8' 9' 10'
Horizontal Maximum H1+H2 2' 6' 10' 12' 15' 18' 21' 24'
D3615, D3615ST, D4215, D4215ST, D7215, D7215ST
Vertical Minimum V1 3' 4' 5' 6' 7' 8' 9' 10'
Horizontal Maximum H1 2' 6' 10' 12' 15' 18' 21' 24'

XG022216
Installation
Figure 8.e Horizontal Termination - 2 Elbows
Figure 8.f Horizontal Termination - 3 Elbows
Horizontal Termination - 2 Elbows
HorizontalTermination-2Elbows
V1
H1
H2
*Minimum 36'' from top of unit before attaching an elbow
HorizontalTermination-3Elbows
Horizontal Termination - 3 Elbows
V1
V2
H1
H2
*Minimum 36'' from top of unit before attaching an elbow
D3615, D3615ST, D4215, D4215ST, D7215, D7215ST
Vertical Minimum V1 3' 4' 5' 6' 7' 8' 9' 10'
Horizontal Maximum H1+H2 2' 6' 10' 12' 15' 18' 21' 24'
D3615, D3615ST, D4215, D4215ST, D7215, D7215ST
Vertical Minimum V1+V2 5' 6' 7' 8' 9' 10'
Horizontal Maximum H1+H2 10' 12' 15' 18' 21' 24'

XG0222 17
Installation
Roof mounted Terminations
The following details are some possible congurations for Roof mounted
terminations. See below.
This section applies to installations where the direct vent termination
will be roof mounted.
Section 3-2-1: Venting Layout
Selection of components and details of venting lay out should adhere
to the following guidelines:
• The maximum termination point is 32’ above the replace. (NOTE:
if the maximum termination height is used, the ame pattern may
be aected).
• The vertical termination must be a minimum 2’ higher than where
the termination exits the roong materials, (asphalt shingles, cedar
shakes, etc). This distance should be measured from the high side of
the roof slope where the ue ashing intersects the roong materials.
• For a detailed diagram of allowed termination locations, see
Appendix A.
• Terminationlocationmustbeaminimum6’froma mechanical air inlet.
• A maximum of three osets (each oset is made up of 2-90° bends)
may be made for vertical vent runs.
• Firestops must be installed as required by National & local codes.
• Ensure all horizontal runs are supported with a minimum of 3
supports per 10’ of venting.
• Install all roof ashing and storm collars as shown.
Figure 9. Top vent, Roof mounted termination with no oset in vent run.
Figure 9.b Top vent, Roof mounted with 1 oset (1 oset= two 90° bends).
Figure 9.c Top vent, Roof mounted with 2 osets (1 oset= two 90° bends).
Section 3-2: Installing a Roof Mounted Direct Vent
Termination (PVTK1SS)
PVTK1 Termination
PVTK1 Termination
PVTK1 Termination
Storm collar
Storm collar
Storm collar
2' min
2' min
2' min
Support ring
Support ring
Support straps OR
Support ring and plates
Support ring and plates
Support plate
Support plate
Firestop
PEXT
PEXT-10
Adaptor
Flue
collar
Firestop
Firestop
Firestop
Obstacle
Obstacle
Firestop
32' max
32' max
32' max
Roof ashing
Roof ashing
Roof ashing

XG022218
Installation
Figure 10. Installing a PTO4-F termination.
Figure 10.b Installing a PTO termination with the MSR frame.
Figure 10.c Installing a PTO termination with the BSR frame.
Figure 10.d Installing a PTO termination with MOSR frame.
Figure 10.e Installing the VSS Vinyl Shield.
Figure 10.f Installing a PTO termination heat guard.
1
12”
2”
12”
12”
This section applies to installations where the direct vent termination
will be wall mounted.
Section 3-3: Installing a Wall Mounted Direct Vent Termination
Installationofterminationwithbuiltinframe
A Termination with a Built-In Frame is installed during framing of a
structure.
1. Frame the termination opening to 11" x 11".
2. Install exterior sheathing to the structure framing.
3. Fasten the termination to the sheathing using a minimum of 4 screws.
MSR Frame
PTO-4 (5"/8")
Termination
PTO-4F (5"/8")
Termination
Installationofaterminationshieldforvinylsiding
The VSS Termination shield is installed when the exterior of a structure
is clad with Vinyl siding. It is placed directly above, and on-center with
the termination.
Installation of termination frame at time of framing
Terminations with a MSR frame allow the installation of the frame prior
to installation of the termination.
1. Frame the termination opening to 12" x 12".
2. Secure the MSR Frame to the exterior sheathing of the structure.
3. Fasten the termination to the MSR Frame using a minimum of 4 screws.
1. Frame the MOSR opening to 12" x 12".
2. Fasten the MOSR frame to the interior side of the studs, concrete,
or nished wall construction using a minimum of 4 screws.
3. Insert the termination into the MOSR frame as shown here, (from
the inside) and attach to the MOSR by installing a min. quantity of 4
bolts into the threaded nuts on the MOSR Frame.
Installation of termination frame at time of framing in masonry
Terminations with a BSR frame allow the installation of the frame in
masonry prior to the installation of the termination
1. Frame the BSR opening to 12" x 12".
2. Secure the BSR Frame to the exterior sheathing of the structure.
3. Fastenthe termination to theBSRFrame using a minimumof4 screws.
BSR Frame PTKOG (5"/8")
Installing heat guards
Installing heat guards overterminations is recommended in installations
where the termination is located within 7' feet above grade, or above
a pedestrian walkway, and may be required by code in public areas.
1. Ensure that the two long mounting brackets are facing the bottom
of the termination (See inset). This will provide more heat protection
at the top of the termination, where temperatures are highest.
2. Attach to the faceplate of the termination using four sheet metal
screws.
1
1”
11”
Framing
Exterior
Sheathing
Fastening Hard-
ware, minimum
4-screws
Framing
Exterior
Sheathing
Fastening Hardware,
minimum 4-screws
PTO-4 (5"/8")
Termination
Framing
Exterior
Sheathing
Fastening Hardware,
minimum 4-screws
Exterior Vinyl
siding
PTO-4 (5"/8")
Termination
VSS Vinyl shield
Installation of termination from inside structure
A Termination with a MOSR Frame is installed from the inside of the
structure. These are commonly used in high-rise construction.
MOSR Frame
PTO-4 (5"/8")
Termination
12”
12”
Fastening Hardware,
minimum 4-screws
Framing,
concrete
or other
materials
Exterior
Sheathing, concrete
or other materials

XG0222 19
Installation
Connectionandinstallationofthevent
components should adhere to the following
guidelines:
Section 3-3-2: Venting Components
The following components and associated Montigo part numbers for
installation of a roof or wall mounted termination. Use of non-Montigo
approved parts will VOID the warranty and may impede operation of
the replace. • Use any combination of rigid and ex pipe as required and in any
orientation (Male connectors can face in any direction).
• Flex sections may be stretched up to 50% of their total length (e.g.
a 24” section maybe stretched to 36”).
• Connect all vent sections using a minimum of three sheet metal
screws on the outer pipe ue.
• Ensure the pipe ends male to female slide in a minimum of 1 1/2”
of overlap.
• Ensure all horizontal runs are supported with a minimum of 3
supports per 10’ of venting.
• When hanging/supporting venting, ensure that 1” clearance is
maintained on sides and bottom of vent runs and 2” above horizontal
vent runs to any combustible material.
• Rigid pipe may be cut less than half way from the FEMALEENDONLY.
• Flex pipe cannot be cut
• Ensure when cutting sections of rigid pipe to maintain integrity of
internal supports.
• For ex venting, place the springs supplied with the pipe kit, between
the outer and inner pipes to keep the pipes separate and avoid any
possible hot spots.
• Montigo recommends the use of a ex section for the nal pipe
connected directly to the replace oering greater exibility of
installation and absorption of movement.
• Firestops must be installed as required by National & local codes.
IMPORTANT:
Please Refer to your Building Envelope Engineer
or Waterproong Consultant for a review of ALL
penetrations through exterior walls or the roof.
A - Termination PTO4 (3" Length)
PTO4F (3" Length)
PVTK1SS
B - Frame Kits MSR (Stucco Frame)
MOSR (Stucco Frame)
BSR-4 (4" Brick Frame)
BSR-6 (6" Brick Frame)
C - Flex Sections PFL - 1 (12" f/f Section)
PFL - 18 (18" f/f Section)
PFL - 2 (24" f/f Section)
PFL - 3 (36" f/f Section)
PFL - 4 (48" f/f Section)
PFL - 6 (72" f/f Section)
D - Rigid Pipe PEXT - 1 (12" f/m Section)
PEXT - 2 (24" f/m Section)
PEXT - 3 (36" f/m Section)
PEXT - 4 (48" f/m Section)
PEXT - 6 (72" f/m Section)
E - Rigid Pipe Extension PXT - 5 (5" f/f Section)
PXT - 12 (12" f/f Section)
PXT - 20 (20" f/f Section)
F-Elbows PEL-90MM (m/m 90º Elbow)
PEL-90FF ( f/f 90º Elbow)
PEL-90FM ( f/m 90º Elbow)
PEL-45FM ( f/m 45º Elbow)
G - Wall Penetration Kit PFVK01F
H-SupportRing&Plate PSPXT-8
I - Firestop FS-8
J - Roof Flashing PRF-7 (1/12 - 7/12 pt.)
PRF-12 (7/12 - 12/12 pt.)
K - Heat Shield RHS101
L - Heat Guard MTKOG

XG022220
Installation
Section3-3-2.2:SimpsonDuraventVentingComponents
The following Simpson Duravent venting components are approved for use with Montigo products. Please
contact your local Montigo dealer for further information.
Component Montigo Part Number Simpson Duravent
Part Number
Termination PTO4 (3" Length)
PTO4F (3" Length)
PVTK1SS (5/8 Vent)
58DVA-HC (Horizontal 5/8 vent)
58DVA-VCH (Vertical 5/8 Vent)
Rigid Sections
(5/8 Vent)
PEXT - 1 (12" f/m)
PEXT - 2 (24" f/m)
PEXT - 3 (36" f/m)
PEXT - 4 (48" f/m)
PEXT - 6 (72" f/m)
58DVA-06 (6")
58DVA-09 (9")
58DVA-12 (12")
58DVA-18 (18")
58DVA-24 (24")
58DVA-36 (36")
58DVA-48 (48")
58DVA-60 (60")
Rigid Pipe Extension PXT12 (12" f/f)
PXT20 (20" f/f)
58DVA-08A (12")
58DVA-16A (20")
Rigid Telescopic Pipe 58DVA-17TA
58DVA-24TA
E-Elbows
(5/8 Vent)
PEL-90MM (m/m 90º)
PEL-90FF ( f/f 90º)
PEL-90FM ( f/m 90º)
PEL-45FM ( f/m 45º)
58DVA-E30 (30°)
58DVA-E45 (45°)
58DVA-E60 (60°)
58DVA-E90 (90°)
SupportRing&Plate PSPXT-8 58DVA-DC
Firestop FS-8 58DVA-WFS
58DVA-FS
Roof Flashing PRF-7 (1/12 - 7/12 pt.)
PRF-12 (7/12 - 12/12 pt.)
58DVA-FF (at roof)
58DVA-F6 (0/12 - 6/12 pt.)
58DVA-F12 (7/12 - 12/12 pt.)
Metal/Tile Roof Flashing 58DVA-F6DS (0/12-6/12 pt.)
58DVA-F12DS (7/12-12/12 pt.)
Heat Shield RHS101 58DVA-WTU
58DVA-WT
Attic Radiation Shield 58DVA-IS
Vinyl Siding Heat Shield VSS
VSSSS
58DVA-VSK (Vinyl Siding Stando Kit)
Wall Support 58DVA-WS
OsetSupport 58DVA-ES
Vaulted Ceiling Support 58DVA-CS
Storm Collar SC8 58DVA-SC
Montigo Fireplace Adapter 58DVA-AD-M1
Montigo Termination Adapter 58DVA-AD-M2