Montigo Prodigy Series Instruction Manual

XG0799 - 081319
Installation & Maintenance Manual
• Theinstallationofthisreplacemustbedonebya
qualiedandcertiedgasapplianceinstaller.
• Checklocalcodesandreadallinstructionspriorto
installation.
®
C
US
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury,
death, or property damage.
—Donotstoreorusegasolineorotherammablevaporsand
liquidsinthevicinityofthisoranyotherappliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phoneinyourbuilding.
• Leavethebuildingimmediately.
• Immediatelycallyourgassupplierfromaneighbor's
phone. Follow the gas supplier’s instructions.
• Ifyoucannotreachyourgassupplier,callthere
department.
—Installationandservicemustbeperformedbyaqualied
installer,serviceagencyorthegastter.
PRODIGY SERIES INDOOR GAS FIREPLACE
SINGLE SIDED, SEE-THROUGH,CORNER RIGHT/LEFT &
PANORAMA FRAMELESS LINEAR FIREPLACE
Natural Gas or Propane Gas
Read and understand this manual. Improper installation, adjustment,
alteration, service or maintenance can cause serious injury, property
damage or even death. For assistance or additional information
consult a qualied installer, service agency or the gas supplier.
Installation and service must be performed by a qualied installer,
service agency or the gas tter.
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
NOTICE
CAUTION
DANGER
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
WARNING

XG0799 - 0813192
General
Congratulations on your purchase of a Montigo Fireplace.
With over 40 years of experience, Montigo is committed to providing
you with a gas fireplace that is not only a beautiful addition to your
space, but that is also designed and manufactured to the highest
safety, reliability and engineering standards.
We strongly encourage you to read and carefully follow the
instructions laid out in this Installation, Operation and Maintenance
Manual and retain it for your future reference. Pay special attention
to all cautions, warnings, and notices throughout this manual
intended to ensure your safety.
This manual covers installation, operation and maintenance. Lighting,
operation and care of this replace can be easily performed by the
homeowner. All installation and service work should be performed
by a qualied or licensed installer, plumber or gas tter as certied
by the state, province, region or governing body where the replace
is being installed.
This installation, operation and maintenance manual is applicable
to the models described in Figure 1. Refer to your rating plate to
verify included options.
Warranty and Installation Information: (See Appendix B)
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
• Modication of the replace and/or components including power
vent module or glass doors.
• Use of any component part not manufactured or approved by
Montigo in combination with this Montigo replace system.
• Installation other than as instructed in this manual.
Consultyour localGas InspectionBranch oninstallation requirements
for factory-built gas fireplaces. Installation and repairs should be
done by a qualified contractor.
Introduction
Safety Alert Key
Indicates a hazardous situation which, if not
avoided, WILL result in death, or serious
injury or property damage.
Indicates a hazardous situation which,
if not avoided, WILL result in minor or
moderate injury.
Indicates a hazardous situation which, if
not avoided, COULD result in death, serious
injury or property damage.
Indicates practices that are important, but
not related to personal injury.
DANGER
CAUTION
WARNING
NOTICE

XG0799 - 081319 3
General
Contents
Safety Alert Key.................................................................................................. 2
Introduction ....................................................................................................... 2
Section A: Before You Begin ......................................................................................... 4
Unit Overview .................................................................................................................... 4
Prodigy Code Breakdown............................................................................................... 5
Prodigy Burner and Venting Size.................................................................................. 5
Section 1: Product Dimensions......................................................................... 6
Single Sided and See-through Dimensions ............................................................... 6
Panorama Dimensions.................................................................................................... 6
Corner Dimensions.......................................................................................................... 7
Framing Flange Dimensions .......................................................................................... 7
Section2:Powervents ...................................................................................... 8
Roof or Wall Mount Power Vent Installation.............................................................. 8
Installing the Power Vent Termination........................................................................ 8
Inline Power Vent Installation........................................................................................ 8
Roof mounted ................................................................................................................... 9
Wall mounted ..................................................................................................................10
In-Line mounted .............................................................................................................11
Flue Gas Louvered Exhaust Termination .................................................................12
Combustion Air Louvered Intake................................................................................13
Section 3: Framing ........................................................................................... 14
Clearance Requirements..............................................................................................14
Framing .............................................................................................................................14
Framing Flanges..............................................................................................................14
Single Sided Framing .....................................................................................................15
See-Through Framing....................................................................................................15
Corner Framing...............................................................................................................15
Panorama Framing.........................................................................................................15
Section 4: Finishing .......................................................................................... 16
Finishing Around the Fireplace ...................................................................................16
Television Installation ....................................................................................................16
Mantle and Hearth.........................................................................................................16
Prodigy Indoor/Outdoor Kit Dimensions..................................................................17
Prodigy Indoor/Outdoor Kit .........................................................................................18
Section 5: Wiring .............................................................................................. 19
Control Panel Installation ............................................................................................. 19
Electrical Connection Directions................................................................................. 21
Damper Connections .................................................................................................... 21
Section 6: Installing the gas line..................................................................... 22
Section 7: Start Up ........................................................................................... 23
LED Remote Control Operation...................................................................... 24
LED Troubleshooting..................................................................................................... 24
Pairing the Remote to the Module (Code Clearing and Code Matching) ......... 25
Inverter Operation ......................................................................................................... 26
Inverter Display ............................................................................................................... 26
Intermittent Problems................................................................................................... 26
Ignition system error codes......................................................................................... 26
Section8:Installing&RemovingtheGlass................................................... 27
Section 9: Installing the Accessories.............................................................. 28
Installing the Glass Media ........................................................................................... 28
Burner Media Quantities.............................................................................................. 28
Driftwood & Speckled Stones ..................................................................................... 28
Optional speckled stones ............................................................................................ 28
Section10:Troubleshooting ........................................................................... 29
Section 11: Cleaning and Maintenance ........................................................ 30
General ............................................................................................................................. 30
Cleaning ............................................................................................................................ 30
Appendix B: Warranty ..................................................................................... 31
Appendix B: Warranty Continued .................................................................. 32
Appendix B: Power Vent Clearances.............................................................. 33
Appendix C: Dampers ...................................................................................... 35
Damper System Overview............................................................................................ 35
Damper Wiring................................................................................................................ 35

XG0799 - 0813194
General
IMPORTANT MESSAGE: SAVE THESE INSTRUCTIONS
The replace must be installed in accordance with these instructions.
Carefully read all the instructions in this manual rst. Consult the Local
Gas Branch to determine the need for a permit prior to starting the
installation. It is the responsibility of the installer to ensure this replace
is installed in compliance with the manufacturers instructions and all
applicable codes.
UnitOverview
• Prodigy series replaces are supplied as a complete system
consisting of rebox, power vent termination (roof mount, wall
mount, or inline) and an electrical control panel. The venting
required for the operation of the system must be eld supplied.
Powervent:
• Details on power venting can be found in Section 2.
• Flue Venting: The ue pipe installed from the rebox to the power
vent module is eld supplied and must be UL or ULc listed type
B vent pipe with an I.D. dimension as shown.
• NOTE FOR INLINE POWER VENT INSTALLATION: The ue pipe
from the outlet side of the inline power vent to the exterior
of the building must be a sealed pressure stack pipe system.
The exhaust gases in this portion of the vent system are under
positive pressure during operation; an unsealed vent pipe will
allow exhaust gases to enter the living space.
• Should the power vent ceaseto function or not provideadequate
draft at any time during operation of the unit, the ue gas vacuum
pressure safety switch will prevent operation of the replace.
CombustionAir:
• The combustion air orfresh air supplyconnections must be piped
to ensure no reduction or restriction to the air supply occurs.
• The amount of air required to safely and eciently run this
unit has been pre-determined and must not be altered without
consultation with the factory. A heat sensor switch will turn
o the burner if a restricted fresh air intake causes vent
temperatures to rise.
• Some locations allow for fresh air to be drawn from the room
in which the replace is installed. This type of installation is
acceptable from a functional perspective so long as adequate
free air is available in the room, but local codes may not allow
this type of air supply. Always check local regulations for air
supply before installing the replace.
Electrical Control Panel:
• Details on system wiring, power requirements and the Montigo
Prodigy control panel can be found in Section 5.
• See the overviews of system components and connections in
Figures 2-4.
Do not use this appliance if any part has been under water.
Immediately call a qualied service technician to inspect the appliance
and to replace any part of the control system and any gas control that
has been under water.
Due to high temperatures, the appliance should be located out of
trac and away from furniture and draperies.
Children and adults should be alerted to the hazards of high surface
temperature and should stay away to avoid burns or clothing ignition.
Clothing or other ammable material should not be placed
on or near the appliance.
Installation and repair should be done by a qualied service person.
The appliance should be inspected before use and at least annually
by a professional service person. More frequent cleaning might be
required due to excessive lint from carpeting, bedding material, etc. It
is imperative that control compartments, burners, and circulating air
passageways of the appliance be kept clean.
NOTICE
NOTICE
NOTICE
NOTICE
NOTICE
Section A: Before You Begin

XG0799 - 081319 5
General
Prodigy Code Breakdown Prodigy Burner and Venting Size
PC
GLASS WIDTH
3 Feet 3
4 Feet 4
5 Feet 5
6 Feet 6
7 Feet 7
8 Feet 8
CONFIGURATION
Corner Right CR
Corner Left CL
Panorama PR
Single Sided -
See Through ST
GLASS HEIGHT
60”
60
36”
36
30”
30
20”
20
12”
12
POWER VENT
In-Line
I
Wall mount
W
Roof mount
R
GAS
Propane
L
Natural gas
N
**Specifications apply to all glass heights
BURNER TYPE
INTAKE / EXHAUST SIZE
12" HIGH 20" HIGH 30" HIGH 36" HIGH 60" HIGH
3' LONG Ribbon Ribbon Ribbon Ribbon Ribbon
4'' LONG Ribbon Hi-low Hi-low Hi-low Hi-low
5'' LONG Ribbon Hi-low Hi-low Hi-low Hi-low
6'' LONG Ribbon Hi-low Hi-low Hi-low Hi-low
7'' LONG Ribbon Hi-low Hi-low Hi-low Hi-low
8'' LONG Ribbon Hi-low Hi-low Hi-low Hi-low
12" HIGH 20" HIGH 30" HIGH 36" HIGH 60" HIGH
INT. EXH. INT. EXH. INT. EXH. INT. EXH. INT. EXH.
3' 2 x 6” 8” 2 x 6” 8” 2 x 6” 8” 2 x 6” 8” 2 x 6” 8”
4' 2 x 8” 10” 2 x 8” 10” 2 x 8” 10” 2 x 8” 10” 2 x 8” 10”
5' 2 x 8” 10” 2 x 8” 10” 2 x 8” 10” 2 x 8” 10” 2 x 8” 10”
6' 2 x 8” 10” 2 x 8” 10” 2 x 8” 10” 2 x 8” 10” 2 x 8” 10”
7' 2 x 8” 10” 2 x 8” 10” 2 x 8” 10” 2 x 8” 10” 2 x 8” 10”
8' 2 x 10” 12” 2 x 10” 12” 2 x 10” 12” 2 x 10” 12” 2 x 10” 12”
PRODIGY SPECIFICATIONS
PC3** PC4** PC5** PC6** PC7** PC8**
MAXIMUM INPUT
NATURAL GAS
(BTU/ HR)
40,000 50,000 75,000 88,000 100,000 112,000
MAX INPUT PROPANE
(BTU/HR) 31,000 52,000 64,000 78,000 105,000 120,000
REQUIRED B-VENT 8” 10” 10” 10” 10” 12”
SIZE OF INTAKES 2 x 6” 2 x 8” 2 x 8” 2 x 8” 2 x 8” 2 x 10”
TOTAL EQUIVALENT
FREE AREA OF INTAKE 56.52 sq.inches 100.48 sq.inches 100.48 sq.inches 100.48 sq.inches 100.48 sq.inches 157 sq. inches
CFM 420 560 700 840 980 1120
ELECTRICAL
REQUIREMENTS
208 VAC Single
Phase 15 Amp
208 VAC Single
Phase 15 Amp
208 VAC Single
Phase 15 Amp
208 VAC Single
Phase 15 Amp
208 VAC Single
Phase 15 Amp
208 VAC Single
Phase 15 Amp
COMPLIANCE ANSI Z21.50-2016 /
CSA 2.22-2016
ANSI Z21.50-2016 /
CSA 2.22-2016
ANSI Z21.50-2016 /
CSA 2.22-2016
ANSI Z21.50-2016 /
CSA 2.22-2016
ANSI Z21.50-2016 /
CSA 2.22-2016
ANSI Z21.50-2016 /
CSA 2.22-2016
CONTROL PANEL
MODEL NUMBER PCGCP1-2-05-DD PCGCP1-2-05-DD PCGCP1-2-05-DD PCGCP1-2-05-DD PCGCP1-2-05-DD PCGCP1-2-05-DD
POWERVENT ROOF PCSBFPV-R03-08 PCSBFPV-R03-10 PCSBFPV-R03-10 PCSBFPV-R03-10 PCSBFPV-R03-10 PCSBFPV-R03-12
POWERVENT WALL PCSBFPV-W03-08 PCSBFPV-W03-10 PCSBFPV-W03-10 PCSBFPV-W03-10 PCSBFPV-W03-10 PCSBFPV-W03-12
POWERVENT INLINE PCINGPV-L03-08 PCINGPV-L03-10 PCINGPV-L03-10 PCINGPV-L03-10 PCINGPV-L03-10 PCINGPV-L03-12

XG0799 - 0813196
General
Single Sided and See-through Dimensions
Panorama Dimensions
Figure 2. Fireplace dimensions (Tolerance ± ⅛").
Figure 2.b Fireplace dimensions (Tolerance ± ⅛").
Section 1: Product Dimensions
SINGLE SIDED AND SEE-THROUGH DIMENSIONS
3' 4' 5' 6' 7' 8'
AIR INTAKE 2 x 6” 2 x 8” 2 x 10”
EXHAUST 8” 10’’ 12”
A 40¼’’ 52¼’’ 64¼’’ 76¼’’ 88¼’’ 100¼’’
B 24’’ 32’’ 40’’ 48’’ 56’’ 60’’
C18⅝’’
D35½" 47½" 59½"71½"83½"95½"
E 12”, 20”, 30”, 36”, 60”
F8⅛
G 42¼’’ 54¼’’ 66¼’’ 78¼’’ 90¼’’ 102¼’’
H 15⅛
I 23 ¼’’+ Glass Height
J 26 3⁄16”+ Glass Height
K19⅞’’
PANORAMA DIMENSIONS
3' 4' 5' 6' 7' 8'
AIR INTAKE 2 x 6” 2 x 8” 2 x 10”
EXHAUST 8” 10’’ 12”
A 4315⁄16 5515⁄16 6715⁄16 7915⁄16 9115⁄16 10315⁄16
B 24’’ 32’’ 40’’ 48’’ 56’’ 60’’
C 13 3⁄8
D43⅝" 55⅝" 67⅝" 79⅝" 91⅝" 103⅝"
E 12”, 20”, 30”, 36”, 60”
F8⅛
G47⅞’’ 59⅞’’ 7115⁄16 8315⁄16 9515⁄16 10715⁄16
H 15⅛
I 23 ¼’’+ Glass Height
J 26 3⁄16”+ Glass Height
K19⅞’’
A
A
B
B
G
G
H
H
K
K
I
I
J
J
D
D
E
E
C
C
F
F
⅝" Flange setback
⅝" Flange setback
⅝" Flange setback
Gas and electrical located on rear
Gas and electrical located on right

XG0799 - 081319 7
General
Corner Dimensions
Figure 2.c Fireplace dimensions (Tolerance ± ⅛").
CORNER DIMENSIONS
3' 4' 5' 6' 7' 8'
AIR INTAKE 2 x 6” 2 x 8” 2 x 10”
EXHAUST 8” 10’’ 12”
A 4315⁄16 5515⁄16 6715⁄16 7915⁄16 9115⁄16 10315⁄16
B 24’’ 32’’ 40’’ 48’’ 56’’ 60’’
C 13 3⁄8
D39¾" 51¾" 6311⁄16 7511⁄16 8711⁄16 99⅝
E 12”, 20”, 30”, 36”, 60”
F8⅛
G47⅞’’ 59⅞’’ 7115⁄16 8315⁄16 9515⁄16 10715⁄16
H 15⅛
I 23 ¼’’+ Glass Height
J 26 3⁄16”+ Glass Height
K19⅞’’
A
B
G
H
K
I J
D
EC
F
Dimensions shown for corner right unit, dimensions are the same for
corner left conguration. Gas and electrical connections will always be
opposite the corner side.
NOTICE
There are framing brackets built into the face of the Prodigy replace.
These brackets extend 1” outwards from the body, and are recessed
5/8” to allow for installation of cement board around the replace.
See specic unit drawings for location of anges as not every
conguration has the same ange position.
Framing Flange Dimensions 1"
1"
⅝
⅝" Flange setback
Gas and
electrical
located on
opposite side
of corner
glass

XG0799 - 0813198
General
ALLOWABLE EXHAUST VENT RUNS
MIN VENT RUN MAX VENT RUN ELBOWS
3' 80’ (Including 7
elbows)
7 @ 90°
ALLOWABLE INTAKE VENT RUNS (B OR C VENT)
MIN VENT RUN MAX VENT RUN ELBOWS
3' 40’ (Including 3
elbows)
3 @ 90°
Section2:Powervents
Roof or Wall Mount Power Vent
Installation
Inline Power Vent Installation
Installing the Power Vent Termination
• Prodigy series replaces are certied for use with any UL listed
type B venting components (B-Vent required for ue gas only).
Use of other non certied parts will void the Montigo warranty,
and may impede the operation of the replace.
• The vent run should not exceed distances described in allowable
exhaust table. Ifyour vent run doesnot meet theserequirements
please contact your local Montigo representative.
• Install components and ttings using the clearances specied
by the B-Vent manufacturer.
• All joints must be secured as per the instructions provided by
the B-Vent manufacturer.
• The exhaust portion of a vent termination must not be recessed
in a wall cavity.
• Horizontal runs must be supported by a minimum of three
supports per 10 feet of venting.
• It is important that the location of the power vent motor is not
exposed to a downfall of water in excess of the standard rain fall.
• Before installing the termination or venting, check to ensure
the planned termination location is acceptable.
InstallationfromreplacetoPV(negativepressuresystem)
• Prodigy series replaces are certied for use with any approved
UL certied type B venting components. Use of other non-
certied parts will void the Montigo warranty, and may impede
the operation of the replace.
• The vent run should not exceed distances described in Table. If
your vent run does not meet these requirements please contact
your local Montigo representative.
• Install components and ttings using the clearances specied
by the B-Vent manufacturer.
• All joints must be secured as per the instructions provided by
the B-Vent manufacturer.
• Horizontal runs must be supported by a minimum of three
supports per 10 feet of venting.
• Select a location for the power vent that will permit an access
panel for future maintenance work.
• Ensure access panel is largeenough for the motor tobe accessed
in case it ever must be removed.
• The power vent can be mounted to any solid non-combustible
surface.
• Anchoring bolts for the power vent should be rated for a
minimum of 300 lbs each and be 1/4” diameter minimum.
• If suspending the power vent, some bracing mechanism should
be designed to prevent any lateral movement of the equipment.
Installationfrom thePVto buildingexterior(positive pressure
system):
• Beyond the inline power vent, venting must be positive pressure
rated with all joints sealed.
• For runs up to 30’, use Montigo VPIF piping. For runs over 30’
use a UL listed sealed venting system.
• The exhaust portion of a vent termination must not be recessed
in a wall cavity.
• Horizontal runs must be supported by a minimum of three
supports per 10 feet of venting.
• The ue gas outlet should be a louver box or termination that
has equivalent free air in square inches as that of the ue collar
• Clearance to combustibles around Montigo VPIF vent is 1".
• Frame the chase for the Power Vent Termination to the
dimensions shown in the power vent section.
• Secure the termination and its frame using appropriately rated
fasteners.
• If more than 7 elbows are required, the maximum allowable
vent run must be decreased by 20’ for each additional elbow.
For example, a vent run with 9x 90° elbows has a maximum
vent run distance of 40 feet.
• Should your vent run fall outside of the parameters shown,
pleasecontact a Montigorepresentative todiscuss otheroptions.

9
Installation
XG0799 - 081319
Roof Mounted
Power vent
Power vent wire
Control
Panel
Control
cable 9
wire
LED Power
120V, 2A
Wall
switch
A
B
B Vent
B or C
Vent
B or C
Vent
MODEL
SIZE
3' 4' 5' 6' 7' 8'
’A’ 7 ⁄” 9 ⁄” 9 ⁄” 9 ⁄” 9 ⁄” 11 ⁄”
’B’ 10 ⁄ “ 12 ⁄ “ 12 ⁄ “ 12 ⁄ “ 12 ⁄ “ 14 ⁄ “
Power supply
wire 208V,
15A
15⁄"
6⁄"
19⁄"
32⁄"
23½"
MAX
Maintain
at least 1"
clearance
around the
collar/sheild
30⁄"
30⁄"
12⁄"
24" 2"
1"

10
Installation
XG0799 - 081319
Wall Mounted
Power vent wire 208V, 15A
Power
vent
Control
Panel
Wall
switch
Control
cable 9
wire
LED Power
120V, 2A
B Vent
A B
MODEL
SIZE
3' 4' 5' 6' 7' 8'
’A’ 7 ⁄” 9 ⁄” 9 ⁄” 9 ⁄” 9 ⁄” 11 ⁄”
’B’ 10 ⁄ “ 12 ⁄ “ 12 ⁄ “ 12 ⁄ “ 12 ⁄ “ 14 ⁄ “
Power supply
wire 208V,
15A
B or C
Vent
B or C
Vent
6⁄" 5"
21⁄"
32½"
30⁄"
30⁄"
10⁄"
2½"
1"
Maintain
at least 1"
clearance
around the
collar/shield
24¼"
24¼"

11
Installation
XG0799 - 081319
In-Line Mounted
Power
vent
Positive
pressure
rated pipe
Power vent wire
Power supply
wire 208V,
15A
Control
Panel
Control
cable 9
wire
LED Power
120V, 2A
Wall
switch
B Vent
MODEL SIZE 3' 4' 5' 6' 7' 8'
’A’ 7 ⁄” 9 ⁄” 9 ⁄” 9 ⁄” 9 ⁄” 11 ⁄”
NeverinstallthePowerVentmotorpointingupordown.
The Power Vent motor must always be installed in the horizontal
plane. Additionally the Power Vent must be securely mounted in a
manner which also allows the possibility for the access door to be
opened. The Motor/Access Door must have at least 12” of additional
clearance to be able to pull out the Motor/Access Door/Fan Wheel
assembly for servicing. -The structure which the Power Vent is
mounted to must be Non-Combustible Material Only.
CAUTION
B or C
Vent
B or C
Vent
8⁄"
4⁄"
17⁄"
23"
7"
9⁄"
14"
11⁄"
19⁄"
A
13⁄"
11" 8½"
16"
*NEVER INSTALL THE MOTOR WITH ITS SHAFT VERTICALLY, THE MOTOR
AXIS MUST BE HORIZONTAL
** ENSURE ACCESS DOOR CAN OPEN AT LEAST 80 DEGREES

12
Installation
XG0799 - 081319
Figure 2. FGLVBI-08 Dimensions
Figure 2.d FGLVBI-08 Framing Dimensions
Figure 2.b FGLVBI-10 Dimensions
Figure 2.e FGLVBI-10 Framing Dimensions
Figure 2.c FGLVBI-12 Dimensions
Figure 2.f FGLVBI-12 Framing Dimensions
FlueGasLouveredExhaustTermination
8" Box
8" Box Framing
10" Box
10" Box Framing
12" Box
12" Box Framing
15.700 OPENING
18.820
13.746 OPENING
16.856
A
A
16.880
15.800
14.746
1 1/2" 6.374 3.928
7 7/8"
13.840
SECTION A-A
!IMPORTANT!
Maintain at least
1.00" clearance
to combustibles
all around the
Flue Gas Box
This flue gas box
is only to be used
with Montigo
fireplace systems
specifically approved
by Montigo
1:6
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FGLVBI-08
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/8"
CHECKED BY
DRAWN BY
DATE
NAME
A
12/20/2017
FGLVBI - FLUE GAS VENT
BOX w/ LOUVER, 8"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
C:\VAULT\_CUSTOM\VENTILATION SYSTEMS\BOXES\VB - Vent\_Spec Dwgs - FLUE GAS\FGLVBI-08
Monday, December 04, 2017 2:43:47 PM
SCALE
15.700 OPENING
18.820
13.746 OPENING
16.856
A
A
16.880
15.800
14.746
1 1/2" 6.374 3.928
7 7/8"
13.840
SECTION A-A
!IMPORTANT!
Maintain at least
1.00" clearance
to combustibles
all around the
Flue Gas Box
This flue gas box
is only to be used
with Montigo
fireplace systems
specifically approved
by Montigo
1:6
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FGLVBI-08
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/8"
CHECKED BY
DRAWN BY
DATE
NAME
A
12/20/2017
FGLVBI - FLUE GAS VENT
BOX w/ LOUVER, 8"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
C:\VAULT\_CUSTOM\VENTILATION SYSTEMS\BOXES\VB - Vent\_Spec Dwgs - FLUE GAS\FGLVBI-08
Monday, December 04, 2017 2:43:47 PM
SCALE
17.800
15.840
VB1-A002
VB1-F-A001
HW2227
HW2227
HW2227
HW2227
FRAMING
!IMPORTANT!
Maintain at least
1.00" clearance
to combustibles
all around the
Flue Gas Box
This flue gas box
is only to be used
with Montigo
fireplace systems
specifically approved
by Montigo
ITEM NO. PART NUMBER DESCRIPTION QTY. REVISION
1 VB1-F-A001-08 8" - TYPE 'VB1', FLUE GAS VENT BOX - STANDARD MOUNTING 1 A
2 VB1-A002 LOUVER ASSEMBLY, VENT BOX, TYPE 'VB1' 1 A*
3 HW2227 SCREW, PAN, #10-24 X 1 1/4", PHIL, SS 4 A
1:8
SIZE
DWG. NO.
A
REV.
SHEET 2 OF 2
WEIGHT:
VENT BOX FRAMING
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/8"
CHECKED BY
DRAWN BY
TC
DATE
NAME
12/20/2017
Flue Gas Box Framing
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
C:\VAULT\_CUSTOM\VENTILATION SYSTEMS\BOXES\VB - Vent\x Framing\VENT BOX FRAMING
Monday, August 12, 2019 8:35:34 AM
SCALE
VB006-20
HW2227
VB026-20
HW2227
HW2227
HW2227
23.800
21.800
FRAMING
!IMPORTANT!
Maintain at least
1.00" clearance
to combustibles
all around the
Flue Gas Box
This flue gas box
is only to be used
with Montigo
fireplace systems
specifically approved
by Montigo
ITEM NO. PART NUMBER DESCRIPTION Default/QTY. REVISION
1 VB2-F-A001-10 10" - TYPE 'VB2', FLUE GAS VENT BOX - STANDARD MOUNTING 1 A*
2 VB2-A002 LOUVER ASSEMBLY, VENT BOX, TYPE 'VB2' 1 A*
3 HW2227 SCREW, PAN, #10-24 X 1 1/4", PHIL, SS 4 A
1:10
SIZE
DWG. NO.
A
REV.
SHEET 2 OF 3
WEIGHT:
FGLVBI-10
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/8"
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
5/28/2019
FGLVBI - FLUE GAS VENT
BOX w/ LOUVER, 10"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
C:\VAULT\_CUSTOM\VENTILATION SYSTEMS\BOXES\VB - Vent\_Spec Dwgs - FLUE GAS\FGLVBI-10
Tuesday, May 28, 2019 11:12:53 AM
SCALE
VB2-A002
HW2227
HW2227
HW2227
HW2227
VB2-F-A001
23.800
21.800
FRAMING
!IMPORTANT!
Maintain at least
1.00" clearance
to combustibles
all around the
Flue Gas Box
This flue gas box
is only to be used
with Montigo
fireplace systems
specifically approved
by Montigo
ITEM NO. PART NUMBER DESCRIPTION Default/QTY. REVISION
1 VB2-F-A001-12 12" - TYPE 'VB2', FLUE GAS VENT BOX - STANDARD MOUNTING 1 A*
2 VB2-A002 LOUVER ASSEMBLY, VENT BOX, TYPE 'VB2' 1 A*
3 HW2227 SCREW, PAN, #10-24 X 1 1/4", PHIL, SS 4 A
1:10
SIZE
DWG. NO.
A
REV.
SHEET 2 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
DATE
NAME
A
8/12/2019
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Monday, August 12, 2019 8:45:01 AM
SCALE
FGLVBI - FLUE GAS VENT
BOX w/ LOUVER, 12"
FGLVBI-12
21.700
24.820
19.746 22.856
C
C
22.880
21.800
20.746
1 1/2" 6.380 3.892
9 7/8"
19.800
SECTION C-C
!IMPORTANT!
Maintain at least
1.00" clearance
to combustibles
all around the
Flue Gas Box
This flue gas box
is only to be used
with Montigo
fireplace systems
specifically approved
by Montigo
1:7
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 3
WEIGHT:
FGLVBI-10
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/8"
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
5/28/2019
FGLVBI - FLUE GAS VENT
BOX w/ LOUVER, 10"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
C:\VAULT\_CUSTOM\VENTILATION SYSTEMS\BOXES\VB - Vent\_Spec Dwgs - FLUE GAS\FGLVBI-10
Tuesday, May 28, 2019 11:12:53 AM
SCALE
21.700
24.820
19.746 22.856
C
C
22.880
21.800
20.746
1 1/2" 6.380 3.892
9 7/8"
19.800
SECTION C-C
!IMPORTANT!
Maintain at least
1.00" clearance
to combustibles
all around the
Flue Gas Box
This flue gas box
is only to be used
with Montigo
fireplace systems
specifically approved
by Montigo
1:7
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 3
WEIGHT:
FGLVBI-10
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/8"
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
5/28/2019
FGLVBI - FLUE GAS VENT
BOX w/ LOUVER, 10"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
C:\VAULT\_CUSTOM\VENTILATION SYSTEMS\BOXES\VB - Vent\_Spec Dwgs - FLUE GAS\FGLVBI-10
Tuesday, May 28, 2019 11:12:53 AM
SCALE
21.700
24.820
19.746 22.856
C
C
22.880
21.800
20.746
1 1/2" 6.380 3.892
9 7/8"
19.800
SECTION C-C
!IMPORTANT!
Maintain at least
1.00" clearance
to combustibles
all around the
Flue Gas Box
This flue gas box
is only to be used
with Montigo
fireplace systems
specifically approved
by Montigo
1:7
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 3
WEIGHT:
FGLVBI-10
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/8"
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
5/28/2019
FGLVBI - FLUE GAS VENT
BOX w/ LOUVER, 10"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
C:\VAULT\_CUSTOM\VENTILATION SYSTEMS\BOXES\VB - Vent\_Spec Dwgs - FLUE GAS\FGLVBI-10
Tuesday, May 28, 2019 11:12:53 AM
SCALE
21.70 OPENING FOR LOUVER
24.82
19.75
OPENING
FOR
LOUVER
22.86
A
A
20.75 11.88
19.80
3.89 6.38 1.50
SECTION A-A
21.80
22.88
!IMPORTANT!
Maintain at least
1.00" clearance
to combustibles
all around the
Flue Gas Box
This flue gas box
is only to be used
with Montigo
fireplace systems
specifically approved
by Montigo
1:8
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
DATE
NAME
A
8/12/2019
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Monday, August 12, 2019 8:45:01 AM
SCALE
FGLVBI - FLUE GAS VENT
BOX w/ LOUVER, 12"
FGLVBI-12
21.70 OPENING FOR LOUVER
24.82
19.75
OPENING
FOR
LOUVER
22.86
A
A
20.75 11.88
19.80
3.89 6.38 1.50
SECTION A-A
21.80
22.88
!IMPORTANT!
Maintain at least
1.00" clearance
to combustibles
all around the
Flue Gas Box
This flue gas box
is only to be used
with Montigo
fireplace systems
specifically approved
by Montigo
1:8
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
DATE
NAME
A
8/12/2019
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Monday, August 12, 2019 8:45:01 AM
SCALE
FGLVBI - FLUE GAS VENT
BOX w/ LOUVER, 12"
FGLVBI-12
21.70 OPENING FOR LOUVER
24.82
19.75
OPENING
FOR
LOUVER
22.86
A
A
20.75 11.88
19.80
3.89 6.38 1.50
SECTION A-A
21.80
22.88
!IMPORTANT!
Maintain at least
1.00" clearance
to combustibles
all around the
Flue Gas Box
This flue gas box
is only to be used
with Montigo
fireplace systems
specifically approved
by Montigo
1:8
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
DATE
NAME
A
8/12/2019
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Monday, August 12, 2019 8:45:01 AM
SCALE
FGLVBI - FLUE GAS VENT
BOX w/ LOUVER, 12"
FGLVBI-12
21.70 OPENING FOR LOUVER
24.82
19.75
OPENING
FOR
LOUVER
22.86
A
A
20.75 11.88
19.80
3.89 6.38 1.50
SECTION A-A
21.80
22.88
!IMPORTANT!
Maintain at least
1.00" clearance
to combustibles
all around the
Flue Gas Box
This flue gas box
is only to be used
with Montigo
fireplace systems
specifically approved
by Montigo
1:8
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
DATE
NAME
A
8/12/2019
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
Monday, August 12, 2019 8:45:01 AM
SCALE
FGLVBI - FLUE GAS VENT
BOX w/ LOUVER, 12"
FGLVBI-12
Maintain at least 1" clearance to combustibles all around the ue
gas box. This ue gas box is only to be used with Montigo replace
systems specically approved by Montigo.
NOTICE
13.746" Opening
19.746"
15.700" Opening
FRONT FRONT FRONT
TOP
TOP TOP
SIDE
SIDE
SIDE
21.700"
16.856"
22.856"
18.820"
24.820"
24.820"
16.880"
17.8" 23.8"
23.8"
15.84"
21.8"
21.8"
22.880"
22.880"
15.800"
13.840"
19.800" 19.800"
11.88"
6.374" 6.380"
6.380"
3.928"
3.892" 3.892"
14.746"
20.746"
20.75"
7⅞"9⅞"
1½"1½"1½"
21.800"
21.800"
19.75" 22.86"
21.700"

13
Installation
XG0799 - 081319
Figure 2. CALVB-06 Dimensions
Figure 2.d CALVB-06 Framing Dimensions
Figure 2.b CALVB-08 Dimensions
Figure 2.e CALVB-08 Framing Dimensions
Figure 2.c CALVB-10 Dimensions
Figure 2.f CALVB-10 Framing Dimensions
CombustionAirLouveredIntake
6" Box
6" Box Framing
8" Box
8" Box Framing
10" Box
10" Box Framing
16.856
13.746 OPENING FOR LOUVER
18.820
15.700 OPENING FOR LOUVER
C
C
14.062
16.880
5.873
4.898 5.434 1.470
14.746
12.001
SECTION C-C
1:6
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
CALVB-06
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/8"
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
21/03/2018
CALVB - COMBUSTION AIR
VENT BOX w/ LOUVER, 6"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
C:\VAULT\_CUSTOM\VENTILATION SYSTEMS\BOXES\VB - Vent\_Spec Dwgs - COMBUSTION AIR\CALVB-06
March-14-18 2:50:14 PM
SCALE
16.856
13.746 OPENING FOR LOUVER
18.820
15.700 OPENING FOR LOUVER
C
C
14.062
16.880
5.873
4.898 5.434 1.470
14.746
12.001
SECTION C-C
1:6
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
CALVB-06
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/8"
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
21/03/2018
CALVB - COMBUSTION AIR
VENT BOX w/ LOUVER, 6"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
C:\VAULT\_CUSTOM\VENTILATION SYSTEMS\BOXES\VB - Vent\_Spec Dwgs - COMBUSTION AIR\CALVB-06
March-14-18 2:50:14 PM
SCALE
16"
14"
VB1-A002
VB1-C-A001
HW2227
HW2227
HW2227
HW2227
ITEM NO. PART NUMBER DESCRIPTION Default/QTY. REVISION
1 VB1-C-A001-06 STANDARD CONFIGURATION - VENT BOX BASE MODULE, TYPE 'VB1' 1 A
2 VB1-A002 LOUVER ASSEMBLY, VENT BOX, TYPE 'VB1' 1 A*
3 HW2227 SCREW, PAN, #10-24 X 1 1/4", PHIL, SS 4 A
1:8
SIZE
DWG. NO.
A
REV.
SHEET 2 OF 2
WEIGHT:
CALVB-06
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/8"
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
21/03/2018
CALVB - COMBUSTION AIR
VENT BOX w/ LOUVER, 6"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
C:\VAULT\_CUSTOM\VENTILATION SYSTEMS\BOXES\VB - Vent\_Spec Dwgs - COMBUSTION AIR\CALVB-06
March-14-18 2:50:14 PM
SCALE
VB1-A002
HW2227
HW2227
HW2227
HW2227
VB1-C-A001
16.000
14.000
ITEM NO. PART NUMBER DESCRIPTION Default/QTY. REVISION
1 VB1-C-A001-08 8" - TYPE 'VB1', COMBUSTION AIR VENT BOX - STANDARD MOUNTING 1 A
2 VB1-A002 LOUVER ASSEMBLY, VENT BOX, TYPE 'VB1' 1 A*
3 HW2227 SCREW, PAN, #10-24 X 1 1/4", PHIL, SS 4 A
1:8
SIZE
DWG. NO.
A
REV.
SHEET 2 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
13/12/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
December-05-17 9:16:10 AM
SCALE
CALVB - COMBUSTION AIR
VENT BOX w/ LOUVER, 8"
CALVB-08
VB2-A002
HW2227
HW2227
HW2227
HW2227
VB2-C-A001
20.00
22.00
FRAMING
ITEM NO. PART NUMBER DESCRIPTION Default/QTY. REVISION
1 VB2-C-A001-10 10" - TYPE 'VB2', COMBUSTION AIR VENT BOX - STANDARD MOUNTING 1 A*
2 VB2-A002 LOUVER ASSEMBLY, VENT BOX, TYPE 'VB2' 1 A*
3 HW2227 SCREW, PAN, #10-24 X 1 1/4", PHIL, SS 4 A
1:10
SIZE
DWG. NO.
A
REV.
SHEET 2 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
13/12/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
December-05-17 9:44:45 AM
SCALE
CALVB - COMBUSTION AIR
VENT BOX w/ LOUVER, 10"
CALVB-10
13.75
OPENING
FOR
LOUVER
15.70
OPENING FOR LOUVER
18.820
16.856
A
A
14.75
1.50 5.40
12.06
7.88
4.90
SECTION A-A
14.06
16.88
1:6
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
13/12/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
December-05-17 9:16:10 AM
SCALE
CALVB - COMBUSTION AIR
VENT BOX w/ LOUVER, 8"
CALVB-08
13.75
OPENING
FOR
LOUVER
15.70
OPENING FOR LOUVER
18.820
16.856
A
A
14.75
1.50 5.40
12.06
7.88
4.90
SECTION A-A
14.06
16.88
1:6
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
13/12/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
December-05-17 9:16:10 AM
SCALE
CALVB - COMBUSTION AIR
VENT BOX w/ LOUVER, 8"
CALVB-08
13.75
OPENING
FOR
LOUVER
15.70
OPENING FOR LOUVER
18.820
16.856
A
A
14.75
1.50 5.40
12.06
7.88
4.90
SECTION A-A
14.06
16.88
1:6
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
13/12/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
December-05-17 9:16:10 AM
SCALE
CALVB - COMBUSTION AIR
VENT BOX w/ LOUVER, 8"
CALVB-08
22.86
19.75
OPENING
FOR
LOUVER
21.70 OPENING FOR LOUVER
24.82
A
A
18.14
9.88
4.87 5.40 1.50
20.75
SECTION A-A
20.14
22.88
1:8
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
13/12/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
December-05-17 9:44:45 AM
SCALE
CALVB - COMBUSTION AIR
VENT BOX w/ LOUVER, 10"
CALVB-10
22.86
19.75
OPENING
FOR
LOUVER
21.70 OPENING FOR LOUVER
24.82
A
A
18.14
9.88
4.87 5.40 1.50
20.75
SECTION A-A
20.14
22.88
1:8
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
13/12/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
December-05-17 9:44:45 AM
SCALE
CALVB - COMBUSTION AIR
VENT BOX w/ LOUVER, 10"
CALVB-10
22.86
19.75
OPENING
FOR
LOUVER
21.70 OPENING FOR LOUVER
24.82
A
A
18.14
9.88
4.87 5.40 1.50
20.75
SECTION A-A
20.14
22.88
1:8
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
13/12/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
December-05-17 9:44:45 AM
SCALE
CALVB - COMBUSTION AIR
VENT BOX w/ LOUVER, 10"
CALVB-10
22.86
19.75
OPENING
FOR
LOUVER
21.70 OPENING FOR LOUVER
24.82
A
A
18.14
9.88
4.87 5.40 1.50
20.75
SECTION A-A
20.14
22.88
1:8
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 2
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED BY
DRAWN BY
TC
DATE
NAME
A
13/12/2017
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
December-05-17 9:44:45 AM
SCALE
CALVB - COMBUSTION AIR
VENT BOX w/ LOUVER, 10"
CALVB-10
13.746" Opening
SIDE
15.700" Opening
15.700" Opening
16.856"
18.820"
18.820" 24.82"
16.880" 16.88"
14" 16" 22"
18" 14" 20"
22.88"
12" 12"
5.873"
5.434"
5.40"
5.40"
4.898"
4.90"
4.90"
14.746" 14.75" 20.75" 7.88" 9.88"
1.470"
1.50"1.50"
14.062"
14.06" 20.14"
19.75" 22.86"
21.70"
13.746" Opening
16.856"
18.14"

14
Installation
XG0799 - 081319
Section 3: Framing
When constructing the framed opening, please ensure there is access
to install the gas line when the unit is installed.
NOTICE
Clearance Requirements
Top Rear Sides Floor Glass †
0" 0" 0" 0" 1/8”
NOTES:
† Distance from the edge of the nished materials to ensure removal
of glass is possible for future cleaning and service
**Type B-Vent pipe clearances must meet the B Vent manufacturer’s
recommendation.
Figure 3. Combustible Wall Clearances
To ensure the replace operates safely, all models must maintain the
following clearances:
Framing
Montigo recommends that framing is performed once the unit has been
placed in its nal location.
STEP 1: Frame around the replace as desired. Framing can be installed on
all sides of the replace, or only on the top and sides if a thinner nishing
material will be used. Ensure access is left for connections of gas, electrical
and venting as required.
STEP 2: Complete all venting, gas, and electrical connections.
STEP 3: Backframe the unit with framing materials followed by nishing
materials as required. Ensure access for service as required.
STEP 4: Refer to Section 5: Finishing.
There are anges on the outer edges of the Prodigy series replace that
may be used to install framing around the replace. The use of these
anges is entirely optional; they are provided to simplify installation,
and if they are not needed, they may be ignored.
Framing Flanges

15
Installation
XG0799 - 081319
Single Sided Framing
See-Through Framing
Corner Framing
Panorama Framing
SINGLE SIDED AND SEE-THROUGH FRAMING DIMENSIONS
3' 4' 5' 6' 7' 8'
B 42¼’’ 54¼’’ 66¼’’ 78¼’’ 90¼’’ 102¼’’
C 26 3⁄16”+ Glass Height
CORNER AND PANORAMA FRAMING DIMENSIONS
3' 4' 5' 6' 7' 8'
B 42¼’’ 54¼’’ 66¼’’ 78¼’’ 90¼’’ 102¼’’
C 26 3⁄16”+ Glass Height
Recessing the
Back Edge:
For corner and
panorama
congurations. Be
sure to measure
to conrm facing
material will still
clear the side glass.
19¼
18⅝
19¼
19¼
B
B
B
B
C
C
C
C

16
Installation
XG0799 - 081319
Section 4: Finishing
Finishing Around the Fireplace TelevisionInstallation
Mantle and Hearth
The following illustrates the suggested nishing method for the Prodigy Montigo does not require any special clearances to be maintained
between a wall mounted television and the replace glass. Check the
TV owner’s manual for any manufacturer’s required clearances.
Combustible or non-
combustible mantels and
hearths may be placed above/
below the top of the glass
viewing area. There are no
restrictions on depth for
mantels, for hearth depth
please refer to nishing
instructions.
The Prodigy replace is designed for zero clearance installation. That
is, combustible nishing materials may be installed directly against the
replace body. These materials can be fastened directly to the replace
provided the fasteners do not penetrate further than 1/2” into the unit
or impede glass installation. To ensure glass can be safely removed for
cleaning, it is recommended that ush nishing materials not extend
more than 4” from the replace.
123456
3
2
5
1
4
Fasteners may only
be installed above
the glass mounting
channels. Maximum
penetration into
replace body: 1/2”
Outer Glass
Finishing Material -
can be fastened to
the face of the
replace
Material MUST NOT
extend past the edge
Finishing
materials in
shaded area only
to allow glass
removal
4" maximum
hearth
depth when
directly
below glass
No
restrictions
on mantel
depth

17
Installation
XG0799 - 081319
Prodigy Indoor/Outdoor Kit Dimensions
INDOOR/OUTDOOR KIT DIMENSIONS
3' 4' 5' 6' 7' 8'
A 37¼’ 49¼’’ 61¼’’ 73¼’’ 85¼’’ 973⁄16”
B 40⅛’ 52⅛’’ 64⅛’’ 76⅛’’ 88⅛’’ 100⅛’’
C 40’’ 52’’ 64’’ 76’’ 88’’ 100”
D37⅛’ 49⅛’ 60⅞’ 7215⁄16”85⅛’' 97⅛’'
EGlass Height + 1⅛”
F 109⁄16”
G8⅛”
H Glass Height + 13⁄16”
I 4⅛”+ Glass Height
J 12½"+ Glass Height
A
B
G
H I J
D
E
C
F

18
Installation
XG0799 - 081319
Prodigy Indoor/Outdoor Kit
Waterproof
membrane
Finished replace
Stainless trim
Finishing materials
½"
½"
⅜" Sheeting
Window Kit Throat
2”x 6”
Framing
Step 1- Mount Throat
Support the throat from the
underside. Align the throat with
the fireplace mounting holes
and attach.
Step 5- Framed Glass
Attach the framed glass to the
nutsertsonthe faceof thethroat.
Step 6- Stainless Trim
Install the stainless trim over the
framed glass. The trim attaches
magnetically to the replace, no
other fasteners are required.
Step 6- Finishing Around Fireplace
When installing nishing materials around the replace, leave a ½” gap
between the stainless trim and any nishing materials so that the trim
can be removed for cleaning and servicing.
Step 2- Frame
The window kit is designed to
extend through an outer wall
constructed of 2"x6" framing.
Frame around the fireplace
throat using 2"x6" material and
keeping the framing tight with
the replace body. The replace
is a zero clearance appliance,
so wood framing is acceptable.
Step 3- Sheeting
Attach ⅜" sheeting to 2"x6"
framing.
Step4-WaterproofMembrane
Install a waterproof membrane
(customer supplied) around
the throat. Ax the membrane
to both the sheeting and
perpendicular to the throat.

19
Installation
XG0799 - 081319
Section 5: Wiring
15"7.22"
18.36"
Control Panel Installation
The control panel should be installed in a location that is accessible for
start upandfuture service.The panel’selectroniccomponents canproduce
a whining sound, this should be considered when selecting the panel
location. If noise from the panel is a concern, the panel should be placed
in a room that can be sound proofed. It is not necessary for the panel to
be in a line of sight from the replace, however, this can be helpful for
servicing. PCGCP1-2-05-DD
Panelsmustbesurfacemountedwithaminimum2”clearanceon
allsidesofthepaneltoensureadequateventilation.
Material: 16 Gauge satin coated steel
Power Supply: Single Phase 200–240VAC + Neutral, 15 A, dedicated circuit
Circuit Breakers in Panel: 15 Amps (Qty 2), 5 Amps (Qty 1)
Power Output to PV Motor: 0.5 hp – 3 Phase, 220 Volts, 2.8 Amps
Pre-purge: 60 seconds
Post-purge: 3 minutes
Damper Power Supply: 24VAC, 40VA
Qty Part No. Description
1 EC1454 Circuit breaker, 5A, 125V
2 EC1456 Circuit breaker, 15A, 250V
2 EC1142 Transformer Class 2, Input 110VAC 60Hz - Output 24VAC 40VA
7 EC1214 Socket, Relay
5 EC1213 Relay w/ indicator light - 24VAC
2 EC1215 Relay w/ indicator light - 110VAC
1 EC1413 Fixed DOM Timer @ 60 Sec.
1 EC1035 Control, Timer Delay - 120VAC 10 AMPS
1 EC1203 Terminal Block, 10 Pole
1 EC2050 Inverter 200-240V .4kW
1 GC3073 Direct Ignition Module
1 GC3097 Rectier Cable
1 GC3096 SIT Gas Valve
1 GC3074 Spark Igniter
R1R1
24V
T1
R2
R4
Terminal
Block
678 9 10
2345 1
Orange
Purple
Red
Brown
R1
Fireplace
NO
Wall Switch
110V
Blue
Red
Orange
Red Red
Brown
Yellow Yellow
Power Vent
Inverter
Hedy HD700
U V W
0V DI1 DI2
PE
AC LINE
MOTOR
R4 R5
Power Vent
MTR
2
1
34
5
Red
White
Black
White/Black
R6
110 Volt
Relays
Blue
Yellow
Orange
R6
Power Vent
Direction Switch
Heat Sensor
Switch
NC
Flue Gas
Switch
Black
White
LED LIGHTING
Controller
T.C.
Pre-purge
Timer
Post-purge Timer
Gas Valve
GND (MV)
GND (BURNER)
MV
24V (TH)
24V (GND)
SPARK
Direct Spark
Ignition
Controller
PWR
Supply
5A
15A
N
N
N
15A
Green (GND)
White (N)
110V 24V
T2
L1
L3
N
N
R7
R2
R2
End SW
R3
R7
R7
R3
Black (L1)
Black (L2)
R3
Damper
Red Brn
WhiteBlk
MTR MTR MTR
R5
Blk Blk Blk
Grey Grey
120V
White (N)
Black (L)

20
Installation
XG0799 - 081319
Power Vent
Inverter
Power Vent
Reversal
Switch
Pre-Purge
Timer
Post-Purge
Timer
Relays
w/LED
6
Transformers
Connections
Damper Connection
Fuse Panel
Control Panel, openedControl Panel, side