MOOD ProFusion iS User manual

REV02072014
Have questions or need assistance? Contact us at 800 345.5000.
ProFusion
™
iS
WIFI SETUP GUIDE
ProFusion PL-U2NA WiFi Adapter

REV02072014
Have questions or need assistance? Contact us at 800 345.5000.
Connecting ProFusion iS to Your WiFi Network
Follow the instructions below to configure your ProFusion iS for WiFi connectivity.
1) Connect USB WiFi Adaptor to ProFusion iS
STEP 1 Place your ProFusion iS in shutdown mode by pressing the front panel Standby
button twice.
STEP 2 Press the main power switch on the rear panel of the player to the ‘off’
position.
STEP 3 Fully insert the USB WiFi adaptor into either USB port on the rear panel of the
player.
• The antenna can bend and rotate to accommodate most installations.
• For best performance, make sure the antenna is clear of obstacles and at
least three feet from any large metal objects.
STEP 4 Press the main power switch to the ‘on’ position and allow the player to return
to normal playback mode.
2) Configure WiFi on ProFusion iS
It is important to complete the remaining selections together (detailed steps provided
on the following pages)
A) Enable WiFi
B) Set IP Type
C) Set Static IP
D) Set SSID (ESSID as noted on Device)
E) Set Security
F) Set Password
Once these selections are completed, use BACK to exit the WiFi and Set
Configuration menus to ensure your settings are saved.

REV02072014
Have questions or need assistance? Contact us at 800 345.5000.
A) Enable WiFi
STEP 1 Press the * button to access the Control Panel menu system.
STEP 2 Press the NAVIGATION DOWN button until the current line indicator (>)
is on Network Control, then press the * button.
STEP 3 Press the NAVIGATION UP or NAVIGATION DOWN button until the
current line indicator (>) is on Set Configuration, then press the *
button.
NOTE: If you receive the following message, please contact Mood at
800 345.5000 for further assistance and instructions:
System locked:>ACTIVATE, access to this menu has been restricted.
STEP 4 Press the NAVIGATION UP or NAVIGATION DOWN button until the
current line indicator (>) is on WiFi, then press the * button.
STEP 5 Make sure the current line indicator (>) is next to Enable, then press
the * button.
NOTE: If Disable is displayed on this screen, the WiFi feature is already
enabled. Skip to Set IP Type.
STEP 6 The display will show WiFi is disabled and the current line indicator
(>) will be at Enable, press the * button to confirm enabling of the
WiFi feature.

REV02072014
Have questions or need assistance? Contact us at 800 345.5000.
B) Set IP Type
STEP 1 Press the NAVIGATION DOWN button until the current line indicator (>)
is on Set IP Type, then press the * button.
STEP 2 The screen will show IP Type: and the current setting (DHCP [default]
or STATIC).
a) If the current IP setting is correct, press the NAVIGATION DOWN
button to move the current line indicator (>) to BACK, then press
the * button.
b) To change the IP type, simply press * without moving down.
NOTE: If Static IP is selected, the IP address, subnet, gateway and DNS
information must be entered manually. Menu access for these settings is
only displayed if static IP is chosen. This is described in the next section.
You may need to contact your network administrator for permissions and
other information.
C) Set Static IP (For Static IP configurations only. If DHCP, skip to Set SSID)
STEP 1 Press the NAVIGATION DOWN button to move the current line indicator
(>) to Set IP Address, then press the * button.
STEP 2 Press the NAVIGATION UP or NAVIGATION DOWN buttons to scroll to
the correct number. Move left or right using the NAVIGATION LEFT and
NAVIGATION RIGHT buttons. Verify the IP address and when finished,
press the * button. You can also use the optional remote control
keypad for navigation and IP numbers entry.
NOTE: Each octet must contain three digits. (ex. 192.168.010.001; the
player will not allow a condensed format such as 192.168.10.1)
STEPS 3-6 Press NAVIGATION DOWN, then press the * button, and then repeat
steps 1 and 2 above for Set IP Subnet, Set Gateway, and as
necessary Set DNS (Primary)and Set DNS (Secondary).

REV02072014
Have questions or need assistance? Contact us at 800 345.5000.
D) Set SSID (Noted as ESSID on Device)
STEP 1 Press the NAVIGATION DOWN button to move the current line indicator
(>) to Set ESSID, then press the * button.
STEP 2 A list of networks broadcasting their SSID (ESSID) will be displayed.
This may take a few seconds depending on the number of wireless
networks in your area. Press the NAVIGATION UP or NAVIGATION
DOWN buttons to place the current line indicator (>) next to the
desired network, and then press the * button.
NOTE: If your network does not broadcast its SSID (ESSID), please select
Other from the list. This will allow direct entry of the SSID (ESSID) for your
network. You may need to contact your network administrator for
permissions and other information.
a) Press the NAVIGATION UP or NAVIGATION DOWN buttons to scroll
to through the list of alphanumeric characters. The NAVIGATION
LEFT and NAVIGATION RIGHT buttons move the cursor left and
right. You can also use the optional remote control keypad for IP
entry.
b) Once you have entered and verified the SSID (ESSID), press the *
button.
STEP 3 Press the NAVIGATION DOWN button to move the current line indicator
(>) to Set, then press the * button.

REV02072014
Have questions or need assistance? Contact us at 800 345.5000.
E) Set Security
STEP 1 Press the NAVIGATION DOWN button to move the current line indicator
(>) to Set Security, and then press the * button.
STEP 2 Press the NAVIGATION UP or NAVIGATION DOWN buttons until the
current line indicator (>) is on the desired security type (options are
NONE, WEP, WPA and WPA2), then press the * button.
F) Set Password
STEP 1 Press the NAVIGATION DOWN button to move the current line indicator
(>) to Set Password, and then press the * button.
STEP 2 Press the NAVIGATION UP or NAVIGATION DOWN buttons to scroll to
through the list of alphanumeric characters. The NAVIGATION LEFT
and NAVIGATION RIGHT buttons move the cursor left and right. You
can also use the optional remote control keypad for Password entry.
STEP 3 Once you have entered and verified the password, press the * button.
STEP 4 To exit the WiFi menu, press the NAVIGATION DOWN button to move
the current line indicator (>) to BACK, and then press the * button.
STEP 5 To save your settings and exit the Set Configuration menu, press the
NAVIGATION DOWN button to move the current line indicator (>) to
BACK, and then press the * button.
IMPORTANT: To save your settings, you must exit the WiFi and Set
Configuration menus by ensuring the current line indicator (>) is at BACK in
each of those menus, and then pressing the * button.

REV02072014
Have questions or need assistance? Contact us at 800 345.5000.
This completes the WiFi configuration process. If your ProFusion iS was connected
previously via Ethernet, reset the player by pressing the Standby button twice to enter
Shut Down mode, press the main power switch on the rear panel of the player to the ‘off’
position, disconnect the Ethernet cable. Wait 5 seconds and press the main power switch
to the ‘on’ position.
We recommend performing a Test Connection to confirm wireless connectivity. Since
the WiFi adaptor is an external USB device, the front panel ‘link’ light will not be active.
This is a normal condition when using external USB WiFi.
Thank you for choosing Mood! Should you have any questions or concerns, please
don’t hesitate to contact us at 800 345.5000.