Moore & Wright 150 Series User manual

For more information visit www.moore-and-wright.com Partners in Precision
CALIPER INSTRUCTIONS
Large Digitronic Workshop Caliper 150 Series
Please carefully review these instructions to ensure proper and accurate use of your new Digitronic Caliper.
Function
ON/OFF: Power on/off switch
ABS/INC: Relative/absolute measurement
ZERO: Zero setting button
mm/in: metric/inch conversion
SET: presetting button
HOLD: data hold button
Instructions
• OperatingCondition:
Temperature: 5-40°C
Relative Humidity: ≤80%
• Preventanyliquidfromcontactingtheprotectivesticker
• Neverapplyvoltage(e.g.Engravingwithanelectrograph)onanypartofthisCaliperforfearofdamagingthecircuit
• Presetastartingpointofmeasurementcorrectly(pleaserefertoOperations).
Unless presetting, do not press the “SET” button purposely for fear of measurement error
Technical Specifications
• Resolution:   0.01mm/0.0005"
• Repeatability:   0.01mm/0.0005"
• Accuracy:   0-600mm:+/-0.07mm
• Maximummeasuringspeed: 3mpersecond
• Battery:   CR20323VLithiumBattery
Instructions of Data Output
• Presetzeroandmetric/inchsystem
• Connecttheendoftheinterfacecabletothecomputer.TheothertothedataoutputportofthisCaliper
• StartthisCaliperandsoftware
• Movetheslidertothepositionyouwantandpressthebuttononcontrolboxfordataoutput
• Batterylife:approx.1year
Battery Replacement
Oncedisplaybeginsflashingorevennodisplay,slidethecoveropenasthearrowshowsandreplacewithanewbattery(CR2032)
Note:
 • Thepositivepoleofthebatterymustfaceout
 • Pleasepresetthestartingpointoveragainafterbatteryreplacement
Electronics Data
Output
Battery
Cover
Slider
External Measuring Faces
Internal Measuring Faces
Fine Adjustment
Slider Scale
Locking
Screw
MW150-DDL_Manual_A4.indd 1 21/05/2013 08:07

For more information visit www.moore-and-wright.com Partners in Precision
CALIPER INSTRUCTIONS
Operations
ON/OFF button
 • PressON/OFFbuttonatanypositionwhenthepowerisoff,thisCaliperwillbereadytoworkanddisplaythemeasuringvalue
 • PressON/OFFatanypositionwhenthepowerison,thisCaliperwillswitchoff
ABS/INC button
 • PressABSbuttoninabsolutemode(without“ABS”),thisCaliperisreadyforabsolutemeasurement
 • PressABSbuttoninrelativemode(with“ABS”displaying),thisCaliperisreadyforrelativemeasurementandsimultaneously
displays “ABS”, showing relative mode
 • PressABSatanypositionforrelative/absolutemeasurementinterchange
ZERO button
 • Inrelativemode,pressZERObuttontosetthecurrentpointtozeroandthisCaliperwilldisplayzero
 • Inabsolutemode,pressZERObuttontosetthecurrentpointtothepresetvalueandthisCaliperwilldisplaythisvalue
mm/in button
 • Pressmm/inbuttonatanypositionformetric/inchconversion
SET button and Internal Measuring (Easy one touch set)
 • Forpresettingastartingpoint(thevaluehasbeenpresettozerointhefactory)
 • Witheachonepressonthisbuttonatanyposition,thecurrentpointissettothepresetvalueanddisplaysontheLCD.
The details are as the follows:
Number of
Times Pressed
Preset Value
1 12.7mm/0.5" optional measuring
2 20.32mm/0.8" optional measuring
3 25.4mm/1" for optional measuring
450.8mm/2" for optional measuring
576.2mm/3" for optional measuring
6 101.6mm/4" for optional measuring
7 127mm/5" for optional measuring
8152.4mm/6" for optional measuring
g10mm/0.3935" for optional measuring
10 20mm/0.7870" forinternalmeasuringof600mmcalipers
11 25mm/0.9840" for optional measuring
12 50mm/1.9685" for optional measuring
13 0 standard, after internal and optional
measuring, please set for normal measuring
 • Theprocessiscirculative.Thepresetvalueisheldevenafterpoweringoff
HOLD button
 • Press“H”buttonatanyposition,thisCaliperwillholdthevalueasbeforeanddisplay“H”ontheLCD.
The data will not change even if you move the slider
 • Press“H”buttononceagaintoreleaseholdstate(nocharacter“H”displays),thenthisCaliperdisplaysthemeasuredvalue
RestartthisCaliperafterpoweringoffbypressingON/OFFbutton,itwillkeepthelaststate(mm/in,ABS/INC,SET).
MW150-DDL_Manual_A4.indd 2 21/05/2013 08:07