Mopec DC500 User manual

Rev 6-15-14 ©
DC500
BARIATRIC TILTING AUTOPSY CART
REFERENCE
MANUAL

MOPEC DC500 AUTOPSY CART
MOPEC DC500 AUTOPSY CARTS PAGE 2
IMPORTANT INFORMATION
MODEL NO.:
SERIAL NO.:
DATE OF PURCHASE:
DATE OF INSTALLATION:
INSTALLATION NOTES:
SERVICE AND SUPPORT:

MOPEC DC500 AUTOPSY CART
MOPEC DC500 AUTOPSY CARTS PAGE 3
TABLE OF CONTENTS
INTRODUCTION 4
CUSTOMER AND TECHNICAL SUPPORT 5
UNPACKING 6
CLEANING AND MAINTENANCE 7
STANDARD FEATURES 8
WARRANTY 9
ISO CERTIFICATE 10
UNIT DRAWING 11

MOPEC DC500 AUTOPSY CART
MOPEC DC500 AUTOPSY CARTS PAGE 4
INTRODUCTION
The “DC500” Bariatric Tilting autopsy cart is used in conjunction with Mopec’s
wall mounted autopsy sink or as a simple viewing stretcher, this high load
bearing table has a manual hand crank hydraulic lifting system with dual
cylinders. All Mopec carts now feature our caster system with non corrosive 8”
heavy duty wheels. Caster wheel center is fabricated using state-of-the-art
polyamide plastic with polyurethane treads for years of lasting service. Locking
and braking are accomplished through effortless pedal motion. During transport,
one caster swivel is locked for easy mobility.

MOPEC DC500 AUTOPSY CART
MOPEC DC500 AUTOPSY CARTS PAGE 5
CUSTOMER AND TECHNICAL SUPPORT
All Mopec staff members are Customer Service experts. We believe in providing
nothing but the best possible service for all our customers. Our Technical
Support group includes everyone from our design engineers to members of our
production group. All are dedicated to providing comprehensive and courteous
support to all Mopec customers.
The following information is included to help our customers communicate with
Customer and Technical Support at Mopec.
Mopec
21750 COOLIDGE HWY.
OAK PARK , MICHIGAN 48237
TOLL FREE 800.362.8491
248.291.2040 PH. 248.291.2050 FX

MOPEC DC500 AUTOPSY CART
MOPEC DC500 AUTOPSY CARTS PAGE 6
UNPACKING
1.) Carefully inspect the exterior of the shipping container before
opening. If the crate is damaged and the product has sustained
damage then immediately contact Mopec and the freight carrier.
Never discard the shipping container even if it is damaged
beyond recognition.
2.) The receiver must driver note any suspected damage on the bill of
lading and sign it. Mopec will help assist in filing a claim for
product repair and/or replacement.
3.) Carefully open the containers and inspect the goods for concealed
damage. If concealed damage is noticed (i.e. Broken welds,
dented stainless, scratches, etc.) Follow through as noted above,
and again do not discard the shipping material, they are important
in settling claims.

MOPEC DC500 AUTOPSY CART
MOPEC DC500 AUTOPSY CARTS PAGE 7
CLEANING AND MAINTENANCE
DISINFECTING AND MAINTAINING STAINLESS STEEL SURFACES
All stainless steel surfaces can be cleaned with soap and water, which will
remove debris.
The stainless steel surfaces can be disinfected with a non caustic disinfectant.
We suggest using BE045 PathCloud or BE047 Bench Wipe for cleaning
purposes.
We recommend you DO NOT USE a bleach solution to clean your unit, bleach
will eventually erode stainless steel if not thoroughly rinsed. The use of chlorine
bleach will VOID THE STAINLESS STEEL WARRANTY
During the cleaning we suggest wiping the surface in the same direction as the
satin finish which will help elevate dirt from the grain finish.
Scratches can be removed simply by utilizing a "non-metallic" abrasive pad and
rubbing in the same direction as the satin finish.
Since most abrasive pads vary from one supply to another, we suggest rubbing
the entire surface to blend the scratch and blend the balance of the surface.

MOPEC DC500 AUTOPSY CART
MOPEC DC500 AUTOPSY CARTS PAGE 8
STANDARD FEATURES
Removable Cart Top: Fabricated of 14 gauge stainless steel with #4 satin
finish. The top is recessed and dimpled toward the drain hole. A drain plug on a
chain is provided. All exposed welds are ground smooth and grained to match a
#4 satin finish
Cart Frame: Fabricated of 1-1/2” (3.8 cm) heavy gauge stainless steel tubing.
All welding is continuous with an approximate 1/8” (.38 cm) radius bead and are
clean and free of burrs and discoloration.
Tilting: One end of the table can be elevated 6” for better drainage into the sink
Welding: All welding is TIG type welding utilizing only stainless steel as a filler
media. All weld fillets are approximately ¼” (.64 cm) diameter. All welds are
brushed clean removing any weld burns and burrs.
Wheels/Casters: Heavy-duty 8” diameter non corrosive polyamide wheels
feature the Total Lock caster system.
OPTIONAL FEATURES
•Head Rest
DOWN UP
UNLOCKED
OCKED

MOPEC DC500 AUTOPSY CART
MOPEC DC500 AUTOPSY CARTS PAGE 9
WARRANTY
MOPEC DC500 AUTOPSY CART
THE DC500 CART AND ALL PARTS THEREOF, MANUFACTURED BY
MOPEC IS WARRANTED TO OUR CUSTOMERS TO BE FREE FROM
DEFECTS IN MATERIAL AND CONSTRUCTION WHEN SUBJECTED TO
NORMAL USE AND SERVICE. THIS WARRANTY SHALL NOT APPLY TO
ANY EQUIPMENT OR PART THEREOF, WHICH HAS BEEN SUBJECT TO
ALTERATIONS, ACCIDENT, MISUSE, OR WHICH HAS BEEN USED MORE
THAN ITS PUBLISHED CAPACITY.
MOPEC’S OBLIGATION UNDER THIS WARRANTY IS LIMITED TO
REPAIRING OR REPLACING, WITHOUT CHARGE ANY PART OR PARTS OF
SAID EQUIPMENT WHICH PROVE DEFECTIVE AND WHICH OUR
EXAMINATION SHALL DISCLOSE TO OUR SATISFACTION TO BE THUS
DEFECTIVE. WE DO NOT ACCEPT RESPONSIBILITY FOR
CONSEQUENTIAL DAMAGE RESULTING FROM SUCH DEFECTIVE PARTS.
THE PERIOD OF WARRANTY ON MOPEC EQUIPMENT IS AS FOLLOWS:
ALL EQUIPMENT: EQUIPMENT IS WARRANTED IN ITS ENTIRETY
FOR A PERIOD OF ONE (1) YEAR FROM THE DATE OF SALE. THIS
WARRANTY INCLUDES PARTS AND LABOR FOR COVERED
REPAIRS.
MOPEC WILL ACCEPT INCOMING DEFECTIVE PARTS, ONLY WHEN
SHIPMENT IS PREPAID. THIS WARRANTY CONTRACT IS IN LIEU OF ALL
OTHER WARRANTIES, AND RELEASES MOPEC OF ALL OTHER
OBLIGATIONS OR LIABILITIES. IT NEITHER ASSUMES NOR AUTHORIZES
ANY PERSON OR PERSONS TO ASSUME ANY OBLIGATION OTHER THAN
THAT COVERED IN THIS WARRANTY.
MOPEC
21750 COOLIDGE HWY.
OAK PARK , MICHIGAN 48237
TOLL FREE 800.362.8491
248.291.2040 PH. 248.291.2050 FX

MOPEC DC500 AUTOPSY CART
MOPEC DC500 AUTOPSY CARTS PAGE 10