MORDOMUS iZSIRI1 User manual

USER MANUAL
Z-WAVE INDOOR SIREN
iZSIRI1
Z-Wave Certified Device
WELL DONE!
You have picked the finest solution for your smart home, congrats!
Now it's time to enjoy these great features of your new product:
- Audible and visual alarm
- Wireless control, notifications, and trigger by other smart home devices (when included to
a Z-Wave gateway controller)
- Z-Wave Plus with improved 500 chip for faster and safer wireless communication
- Acts as signal repeater when powered by AC adapter
- Sleek design and compact size
SPECIFICATIONS
Model Number: iZSIRI1
Z-Wave Signal Frequency: 908.42 MHz
Volume: 110dB
Power: DC 5V/1A and 4 AAA (1.2V) batteries for back-up power
Range: Up to 100 feet line of sight
Operating Temperature: 14°F to 122°F
Operating Humidity: ≤80%
Installation and Use: Indoor only
1
www.mordomus.com

BEFORE YOU RETURN IT
Let us know if you are having any issues installing or operating the device.
Our fast and friendly tech support is here to help: [e-mail]
Go to mordomus.com to find out how to make your home smarter and safer.
INSTALLATION
Unscrew the back cover of the indoor siren and insert 4 AAA rechargeable batteries or use
the USB power adapter included in the box.
WAIT!
Include the indoor siren to your Z-Wave network before mounting it.
Z-WAVE INCLUSION
1. Bring the siren within 3 feet from your Z-Wave gateway controller
2. Put your Z-Wave controller in inclusion/pairing mode
3. Press and release the Z-Wave button on the siren THREE TIMES quickly
4. A new alarm device should appear on your controller's device list
Z-Wave button
Q: I have not been able to add the device to my network after several attempts, what do I do
now?
A: If you are unable to include the Z-Wave switch to your controller, please try one of the
following:
- Bring the siren closer to your Z-Wave controller
2
www.mordomus.com

- Press and release the Z-Wave button quickly several times once you put the controller in
the inclusion mode to ensure the command has gone through
- Put your controller in the EXCLUSION mode and press and release the Z-Wave button
quickly 3 times, then try adding it to your network again
Z-WAVE EXCLUSION
1. Bring the siren within 3 feet from your Z-Wave gateway controller
2. Put your Z-Wave controller in exclusion/unpairing mode
3. Press and release the Z-Wave button on the siren THREE TIMES quickly
4. The device should disappear from your controller's device list
Please repeat the process following all steps carefully if first attempt is unsuccessful
FACTORY RESET
If your primary controller is missing or inoperable, you may need to reset the device to
factory settings. To complete the process, press and hold the Z-Wave button for 10 seconds.
NOTE: All previously recorded activity and custom settings will be erased from the siren’s
memory.
ASSOCIATION
Once the Z-Wave siren is added to your network, you are able to trigger it with other
components from your network, as well as control and monitor its activity from your mobile
device, or computer.
Depending on your Z-Wave gateway's home automation software capabilities, you may be
able to associate your indoor siren in groups with other Z-Wave devices to schedule scenes
and create events. Indoor siren supports Group 1 with up to five devices for lifeline
communication (Group 2-5 is not supported).
Please refer to your controller's user guide for advanced programming instructions as they
are a little different for every software.
MOUNTING
Find the best spot for your Z-Wave indoor siren - a corner in the living room, garage ceiling,
or anywhere else you see fit. Use the 2 screws included in the box to fix the mounting
bracket to flat surface of your choice.
Once the bracket is securely installed, carefully slide the siren onto the bracket and position
it by tilting it to either side, upwards, or downwards.
WARNING
- This product should be installed indoors upon completion of any renovations
- Prior to installation, the device should be stored in a dry, dust- and mold-proof place
- Do not install the siren in a place with direct sun exposure, high temperature or humidity
- Keep away from chemicals, water, and dust
- Ensure the device is never close to any heat source or open flame to prevent fire
- Ensure the device is connected to an electric power source that does not exceed the
maximum load power
3
www.mordomus.com

- The batteries are only a backup power source and are not recommended for use as the
main power supply
- No part of the device may be replaced or repaired by the user (except batteries)
IN NO EVENT SHALL IOLINE OR ITS SUBSIDIARIES AND AFFILIATES BE LIABLE FOR ANY
INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR DAMAGES
FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY,
WHETHER IN AN ACTION IN CONTRACT, OR OTHERWISE EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IOLINE'S LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY
FOR ANY CAUSE OF ACTION ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE
OR USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF
WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO,
AT IOLINE'S OPTION, REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE FOR THAT
PORTION OF PRODUCTS WITH RESPECT TO WHICH DAMAGES ARE CLAIMED. ALL CLAIMS OF
ANY KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF
PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS
FROM IOLINE'S DELIVERY, OR THE DATE FIXED FOR DELIVERY IN THE EVENT OF
NONDELIVERY.
FCC NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED
BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD
VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. STORE INDOORS WHEN NOT IN
USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT IMMERSE IN WATER. NOT FOR USE
WHERE DIRECTLY EXPOSED TO WATER.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference,
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used according to instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in any given installation.
If this equipment causes harmful interference to radio or television reception, the user may
try to correct the interference by taking one or more of the following measures:
- Reorient or relocate receiving antenna
- Increase the separation between equipment and receiver
- Connect equipment into a separate outlet or circuit from receiver
- Consult the dealer or an experienced radio/TV technician for additional assistance
4
www.mordomus.com