MOREK MEV11DNNNN5T2 User manual

ev.morek.eu
Morek EV Charging Adapter
User Manual

ev.morek.eu
Read this User Manual before you start using the device!
Failure to comply with these instructions may result in injury, damage to the device, harm to
the environment, or other serious issues. Keep this User Manual in a safe place together
with the charging equipment.
▪Use the EV charging adapter only within the specified operating parameters.
▪The EV charging adapter must be used in the design-specified socket, and the socket
outlet must be fixed. Do not use an extension cord.
▪Do not connect the adapter to a power outlet that is not properly grounded.
▪Do not use the adapter in any outlet for which its`s not designed.
▪Do not attempt to open, disassemble, repair, tamper with, or modify the mobile connec-
tor. The connector is not user-serviceable. Contact Morek or local reseller for any issues.
▪Do not use (or discontinue using) the charging adapter if it appears defective, cracked,
frayed, broken, damaged, or fails to operate.
▪Do not disconnect the charging adapter from the wall outlet while the vehicle is
charging.
▪Do not plug the EV charging adapter into a damaged, loose, or worn power outlet.
Ensure that the prongs on the adapter fit snugly into the outlet.
▪Do not use the charging adapter when you, the vehicle, or the adapter itself is exposed
to severe rain, snow, electrical storms, or other inclement weather.
▪Do not immerse the charging equipment in water, and do not directly expose it to water
spray (e.g., from high-pressure cleaners or garden hoses).
▪Do not touch the charging adapters end terminals with sharp metallic objects, such as
wire, tools, or needles. Do not forcefully fold any part of the EV charging adapter or
damage it with sharp objects. Do not insert foreign objects into any part of the EV
charging adapter
▪Protect the charging adapüter from moisture, water, and foreign objects at all times. If
any appear to have corroded or damaged the mobile charger, do not use it.
▪Clean the charging adapter only when it is completely disconnected from the power grid
and the vehicle. Use a cloth designated for cleaning; afterward, carefully dry off all parts.
▪Do not let children play with the packaging material or the charging equipment.
Important:
Safety Information

2ev.morek.eu
• EV 11 kW adaper
• LCD display
• 5m cable
• Type 2 connector
Morek EV 11 kW
EVSE mobile adapter
Use it when traveling or at home.
Compact mobile charging adapter that
should always be with every electric car.
Level 2
Type 2 connectro + CEE 3-Phase 16 A
Plug-and-Charge, Start/stop touch button,
adjustable between 6 - 16A
IP66
IK08
LCD 3.8’’
Energy usage on diplay
EN62752, EN61851-21-2, EN61000-6-1/ -3CE,
CB, TUV, UKCA
Type B, AC 30mA + DC 6mA
Wall (optional with bracket)
>99%
Integrated
3-phase 400V±20% / 1-phase 230V±20%
50/60 Hz
32 A / 16 A
11 kW/ 7.4 kW/ 3.6 kW
6A/ 8A/ 10A/ 13A/ 16A
-25°C to +50°C
Up to 95% non-condensing
≤2000m
Current-leakage, Over-heat, Lightning,
Over-curtent, Over-voltage, Under-voltage,
PE loss, Diode loss Protection
320 (h) x 455 (w) x 110 (d)
2,5
24 months
MEVA01NWPLATE
MEVX01N3PWIRE
MEVH01NHANDLE
Charging mode
Connector type
Charging control
IP protection
Impact strength
Display
Reports
Standard and ertificate t
Leakage protection
Mounting
Efficiency
Power meter
AC power Input rating
Rated frequency
Output current
Output power
Current Switching
Operating temperature
Operating humidity
Altitude
Electrical protection
Dimensions mm
Weight kg
Warranty ter
ket
o 1P Shucko
Product ID MEV11DNNNN5T2
Accessories to mobile adap
Aluminium wall brac
Extension 3P16A t
Cable holder for wall mount
Specifications

3ev.morek.eu
5
7
6
8
5
7
6
8
EV and Power Connection
Power Charged
Time or Delay Charging
Current (Selected)
Fault Alarm
Unit of Power
Delay Charging Icon
Charging Cycle Display
!
kW h
Adjust Current: Touch for 2 seconds until all the green LEDs
flash. Then click to choose the current, selecting between 6A to
16A.
Delay Charging Time: Click to set the delay charging time. The
range is from 0 to 5 hours, and each click adds 0.5 hours.
Metering Reset: Long press for more than 5 seconds to reset
the accumulated charging power.
Instructions
Screen Information

4ev.morek.eu
LED1: Red, faulted indication
LED2: Green1, status indicator, Connection and Current Indication
LED3: Green2, status indicator, Connection and Current Indication
LED4: Green3, status indicator, Connection and Current Indication
Connected
Reserved
Charging
Finishing
Faulted
Cycle light
State Green（1）
Power On Available
6A
8A
10A
13A
16A
Green（3）
Current indication
LED Display Status
RED
Blink x times
Blink
Blink
Blink Blink
Green（2）
LED Display Status
Real-time monitoring has welding detection, temperature detection, PE connection detection,
overvoltage detection, over-current detection, and CP voltage, any failure will be displayed
according to the above table.
LED status Reason LCD Error Code Solutions
Over
Welding Fault
01
02
03
04
05
Power off and check the electric car and
charger
Power off and check the electric car
Power off and check the distribution grid
Power off and check the distribution grid
Please contact the manufacturer
CP voltage error 06 Check if the connector is tight
Overtempera-
Diode loss
07
08
Check shell heat dissipation
Check EV CP diodes
RCD leakage
protection
Ground(PE)
Disconnect
Overvolt-
age/Under voltage
Flash 1 time
Flash 2 times
Flash 3 times
Flash 4 times
Flash 5 times
Flash 6 times
Flash 7 times
Flash 8 times
Error Code and Troubleshooting

5ev.morek.eu
How to use
Step 1: Connect the charging adapter plug to the
appropriate power socket.
Step 2: Select the current and delay charging time
according to your needs.
Step 3: Connect the charging adapter Type 2 plug to
your EV to start charging. Check from the adapters
screen that all is OK.
Step 4: Remove the plug from the socket when
charging is ended or after you have ended it. Unplug
the power plug from the outlet on the wall.
Store the adapter to the storage bag.

Cleaning
Disconnect the adapter from the vehicle and the power socket.
Maintenance
The connectors are sensitive, electrical parts, and their contacts must always be kept
clean and dry. Corrosion on the contacts can lead to impaired function, overheating, or
defects in the device.
Repairs/Modifications
Any repairs and/or modifications may only be performed by the manufacturer. Never
open the housing, and do not make any changes to the charger and control box in any
way by yourself.
If plugs get wet, allow them to dry before using them. Always fit the equipment with the
protective caps when not plugged in.
Only clean the outside of the charging device. Use a soft, slightly damp, or antistatic
cloth.
Do not use any detergents or chemical agents to clean the device.
Maintenance and Cleaning
6ev.morek.eu

Please do not dispose of this appliance in your standard household waste.
This appliance falls under European Directive 2012/19/EU. Have it disposed
of by an authorized waste disposal and recycling firm, in accordance with
local waste management regulations. If you are unsure of the proper
disposal procedure, please consult your local waste management authority.
Recyclable Goods: Please separate the packaging and electrical device by
material type for proper disposal. Place all paperboard and corrugated
fiberboard in your paper recycling bin. Dispose of foils and films at a waste
materials collection center, and take electronic components to a specialist
electrical retailer or a local recycling center for proper disposal.
This device, as well as the manufacturing plants where it is produced, have
been inspected and approved by TÜV Rheinland. The certificate confirms full
compliance with the standards upon which the product is based. This
charging adapter meets the requirements of EU Directives that restrict the
use of certain hazardous substances in electrical and electronic equipment.
7ev.morek.eu
Please sort your waste according to local recycling guidelines

Questions? Make us work harder!
More information about Morek EV chargers and discussions
about EV user cases can be found from ev.morek.eu