Moritex Schott MLEK-A080W1LRD User manual

1
日本語
MG-Wave 定電流照明用電源
MLEK-A080W1LRD
MLEK-A230W1LRD
オプション –KE/-AE/-AC 含む
取扱説明書
- 目 次 -
目次 1 4. 外部装置との接続 5
1. はじめに 1 外部信号接続コネクタについて 5
使用上の注意 2 出力コネクタについて 7
保証 2 5. メンテナンスについて 7
パッケージ内容の確認 3 故障かな?と思ったら 7
2. 特徴 3 6. 仕様 8
3. 設置 4 オプション 9
基本構成について 4 外形寸法 12
各部の名称と働き 4 《MEMO》 13
設置 5 《付録》 14
1. はじめに
製品の安全な使用のためこの取扱説明書を必ずお読みになり、ご理解のうえご使用ください。またお読み
になった後は、本書をいつでも見られるところに保管してください。
警告表示の意味 以下の警告表示は、本書の中で使用されているものです。
表示の内容をよく理解してから、本書をお読みください。
警告
この表示の注意事項を守らないと、軽傷や中程度の障害を負ったり、死亡や
重症に至るおそれがある内容、または重大な物的損害を受けるおそれがあ
る内容を示しています。

2
使用上の注意
警告
以下の内容をご確認のうえ、ご使用ください。
・ 本製品を他の機器と組み合わせて使用する場合、組み合わせる機器との適合はお客様にて確認して
ください。
・ 本製品を他の機器と組み合わせて使用する場合、そのシステムが適合すべき規格・法規・規制はお客
様にて確認してください。
・ 本製品を他の機器と組み合わせて使用する場合、システムの中で本製品が意図した用途に対して適
切に配電・設置・使用されていることはお客様にて確認してください。
・ システム全体として確実な安全対策が施されていない場合、生命や財産に重大な危険を及ぼす可能
性のある設備に本製品を使用しないでください。
・ 本製品に水がかからない場所に設置してください。
・ もし何らかの異物が製品に付着した場合、乾いた布で完全にふき取ってください。
・ 保守部品の定期的な点検および交換をしてください。
・ 不具合が発生した場合、分解することなく弊社まで修理を依頼してください。
その他の注意事項
・ 本製品を廃棄する場合、産業廃棄物として各地域の法令に基づいて処理してください。
・ 寸法と重量などの数値は参考値です。
・ 本製品(添付品・オプション品)の仕様は、改良や他の理由により予告なく変更になる場合があります。
・ 不明な点は、必ず弊社までお問い合わせください。
保証
保証期間
本製品の保証期間は、納入後 2 年間となります。取扱説明書に記載された製品の正しいご使用方法にて
購入日より 2 年以内に故障が発生した場合に限り、無償にて修理いたします。
保証範囲
保証期間中に、製品に弊社の責による不具合が発生した場合は、無償にて故障部分の交換または修理
を実施いたします。ただし、以下の場合は除外されます。
・ 出荷当時の技術水準では予見できなかった場合
・ 本製品以外の原因による場合
・ 弊社以外による改造または修理による場合
・ 本来の使い方以外の使用による場合
・ 落下や衝撃など取り扱いが不適切なために発生した場合
・ 出張修理の場合
・ 天災や公害など弊社の責ではない原因による場合
・ 弊社に不具合の現象を確認する機会がない場合
本製品に関連する直接的または間接的損害については、いかなる責任も負いかねます。また保証の範囲
は、製品の単価を超えないものとします。なお、上記は日本国内での取引および使用を前提といたします。
海外での取引および使用については弊社までお問い合わせください。

3
パッケージ内容の確認
5ページ: 設置 8ページ: 仕様 9ページ: オプション 参照
2. 特徴
使用可能な照明
モリテックス製MG-Waveの照明のうち、以下の照明がご使用になれます。 ※1,※2
MLEK-A080W1LRD : 4ピン / 0.8 [A] 以下の照明
MLEK-A230W1LRD : 4ピン または 4ピン+2ピン / 2.3 [A] 以下の照明
出力
1 チャンネルの出力が可能です。
マニュアル調整機能
前面パネルの出力調整スイッチで出力を調整し、接続された LED 照明を調光することが可能です。
※ MANU/REMO スイッチが、MANU の時のみ有効です。
※ COARSE で粗調整が、FINE で微調整が可能です。
※ 0,1,・・・・,E,F は 16 進数です。
※ (COARSE, FINE)が(0,0)で MIN、(F,F)で MAX になります。
※ (0,0)から(0,5)程度まで、出力しない範囲があります。
リモート調整機能
後面パネルの外部信号接続コネクタに8ビットのデジタル信号を入力する事で出力を調整し、接続された
LED 照明を調光することが可能です。
※ MANU/REMO スイッチが、REMO の時のみ有効です。
出力 ON/OFF 機能
外部コネクタに信号を入力する事により、接続されたLED照明を消灯できます。
※ MANU/REMOに関係なく動作します。
制御エラー信号出力
照明未接続時、照明への出力を遮断し、外部信号接続コネクタに制御エラー信号を出力します。
※ MANU/REMOに関係なく動作します。
警告
※1 指定された照明以外は接続しないでください。
※2 指定された電流値を超えないようにしてください。
部品名 数量 単位 備考
本体 1 個 -
ACコードセット 1 本 ※
取扱説明書 1 冊 本書
※ ご購入時の型番の接尾辞により、『-100V』には『MC-AC100A-2.0M』が、『-200V』には
『MC-AC200A-2.0M』が添付されております。電源接続前に、主電源コードが使用される
国の法律・規格を満足し、電源電圧・温度の仕様条件に合っているか確認してください。

4
3. 設置
基本構成について
・ 本装置と MG-Wave の照明を接続することでご使用になれます。
・ 外部信号接続コネクタに信号を接続してご使用になれます。
※ ファン付照明は照明ファン用出力コネクタを使用します。(MLEK-A230W1LRD のみ)
※ オプションで、外部接続ケーブル・照明用中継ケーブル・照明ファン用中継ケーブルもあります。
(MC-EXC-02, M-RCB4**L, M-RCB0**L)
各部の名称と働き
① 電源スイッチ 『 I 』側にすると、電源が入ります。
② パワーインジケータ 電源が入っている時に点灯します。
③ MANU/REMO スイッチ 出力調整のマニュアルとリモートを設定します。
④ 出力調整スイッチ マニュアルの時に、出力を調整します。
⑤ 照明用出力コネクタ:OUT 照明を接続します。
⑥ 照明ファン用出力コネクタ:FAN ファン付照明のファンケーブルを接続します。
⑦ 冷却ファン 内部を冷却します。(吸い込み)
⑧ 外部信号接続コネクタ:EXT 外部機器を接続するためのコネクタです。
⑨ AC インレット AC ケーブルを差し込みます。
⑩ 側面空気穴 冷却用ファンの空気穴です。(吐き出し)
⑪ ゴム足 オプションの取付ブラケットを使用するときは外します。
※ 図は MLEK-A230W1LRD のものです。
※ ⑥,⑦は MLEK-A080W1LRD にはありません。

5
設置
ゴム足を下にした水平設置。
※ 設置後、本体周囲に 10mm 以上の空間を確保してください。
※ 電源スイッチのON/OFF が容易に行える場所、あるいはインレットまたはプラグが容易に取り外せる場
所に設置してください。
※ 感電保護 : クラスⅠ機器。
※ 使用する際には、入力する AC 電圧と使用する国や地域の規格に適合した適切な電源コードをご使
用ください。
※ 以下の構成にて EU 指令/EN 規格に適切に適合することができます。
長さ:3m 以下 端子:L/N/PE
クラスⅠ機器用プラグにて保護接地端子に接続
オプションの MC-AC200A-2.0M は上記規格に適合しております。
4. 外部装置との接続
警告
・接続する機器の一次側の回路から強化絶縁以上で分離された SELV 回路
以外は接続しないでください。
・外部信号接続ケーブルは必ずシールド線を使用し、長さは 2 m 以下
を推奨します。(オプション: MC-EXC-02)
・過大な入力や過負荷はしないでください。
外部信号接続コネクタについて (EXT)
型式
ピンアサイン
№ 名 称 № 名 称
18bitデジタル入
力
20
(
LSB
)
9 COMMON (+) ※1
28bitデジタル入
力
2110 出力ON/OFF信号(入力) ※2
38bitデジタル
入力
2211 制御エラー信号出力 ※4
48bitデジタル
入力
23※3 12 NC
58bitデジタル入
力
2413 NC
68bitデジタル入
力
2514 NC
78bitデジタル
入力
2615 NC
88bitデジタル入
力
27
(
MSB
)
※1
※2
※3
※4
・ MANU/REMOに関係なく出力いたします。
オープンエミッタ出力です。
・ MANU/REMOに関係なく動作します。
・ ”L”入力時 1回路あたりの電流 COMMON 5 V時 : 1 mA 、 COMMON 24 V時 : 6 mA
・ オープンコレクタ入力が可能です。
”L”入力時 ・・・・・・・・・・・・・・・・・・・・・・・・・・・ 出力OFF
REMOのみ有効です。(出力の状態については真理値表を参照)
・ オープンコレクタ入力が可能です。
正常時 : 出力オープン
エラー時 : 出力COMMONショート
・ 4 mA 以下の電流でご使用ください。
・ 使用中の入力変動は行わないでください。
”H”(COMMON)入力またはオープン時 ・・・・・ 出力ON
電流 COMMON 5 V時 : 1 mA 、 COMMON 24 V時 : 6 mA
5 V から 24 Vに対応しています。
HDAB-15S(05) : コネクタ(メス) (HRS製)
HDA-CTH : コネクタケース (HRS製)
HDAB-15P(05)(オス)
(HRS製)
固定ネジ M2.6
外部ケーブル側コネクタ
または 同等品
本体側コネクタ

6
真理値表
入出力回路例
5 V
47k
1
5 V - 24 V
8
5 V
47k
MSB
3.9k
A
10
11
Photo-couplerRelay Transistor
5 V, 24 V
ON/OFF
COMMON
Error
A
A
BB
A A
5 V, 24 V
LSB
5 V
5V = 1.3k
5 V
9
24V = 6.2k
3.9k
330
3.9k
47k
COARSE FINE
出力
ON/OFF
Bit
2
7
Bit
2
6
Bit
2
5
Bit
2
4
Bit
2
3
Bit
2
2
Bit
2
1
Bit
2
0
出力(照明)の状態 制御
エラー
× × L ×××××××× 出力OFF ×
× × H ×××××××× 出力ON ×
× × × ×××××××× 制御エラー H
00H LLLLLLLL MIN出力 L
01H LLLLLLLH L
0 2 H LLLLLLHL L
: : : :::::::: : L
: : : :::::::: : L
F D H HHHHHHLH L
FEH HHHHHHHL L
FFH HHHHHHHH MAX出力 L
入力 H : High(COMMON)入力 または 入力オープン
L:Low 入力
出力 H : 出力 COMMONショート (カプラON)
L : 出力 オープン (カプラOFF)
× : H ・ L 任意
(COARSE,FINE) が (0,5) 程度まで点灯しない範囲があります。
出力
出力調整スイッチ 外部信号 COMMON +

7
出力コネクタについて (MG-Wave 照明用)
型式
(MLEK-A230W1LRD のみです。)
ピンアサイン: 照明用出力コネクタ (OUT)
ピンアサイン: 照明ファン用出力コネクタ (FAN)
5. メンテナンスについて
警告
・お手入れをする時は、必ず電源を切り、外部機器との接続を全てはずして
から行ってください。
・絶対に分解はしないでください。
・ 本体の汚れは、乾いた布でふき取ってください。
・ 汚れがひどい時は、布に薄めた中性洗剤を含ませ、かたくしぼってから汚れをふき取ってください。
故障かな?と思ったら
症状 原因 対策
照明が点灯しない
照明が暗い
・照明は正しく接続されていますか?
・MANU/REMO の設定は正しいですか?
・出力調整はされていますか?
・外部機器が正しく接続されていますか?
・照明を正しく接続してください
・MANU/REMO を確認してください
・調整してください
・外部機器を正しく接続してください
ON/OFF しない ・外部機器が正しく接続されていますか? ・外部機器を正しく接続してください
信号が出ない ・外部機器が正しく接続されていますか? ・外部機器を正しく接続してください
№ 名 称
1 電流出力 (+) ※1
2 センシング (+) ※2
3 センシング (-) ※2
4 電流出力 (-) ※1
※1
※2
オプション: M-RCB4**L
MG-Waveシリーズの照明(4ピンタイプ)以外、絶対に接続しないでください。
出力電圧は 12.5 [V] 以下です。
MG-Waveシリーズの照明(4ピンタイプ)は、全てセンシング調整済みです。
№ 名 称
1 電圧出力 (+) ※1
2 電圧出力 (-) ※1
※1
オプション: M-RCB0**L
出力電圧は 12.5 [V] 以下です。
※1
※2
SMP-02V-BC (JST製) SMR-02V-B (JST製) または 同等品
※1 照明用出力コネクタ。
※2 照明ファン用出力コネクタ。その他の用途にはご使用になれません。
本体側出力コネクタ 照明側コネクタ
SMP-04V-BC (JST製) SMR-04V-B (JST製) または 同等品

8
6. 仕様
MLEK-A080W1LRD MLEK-A230W1LRD
※1
0.3/0.15 [A]
(AC 100 / 240 [V])
0.7/0.4 [A]
(AC 100 / 240 [V])
15 [A] max. at AC 100 [V]
35 [A] max. at AC 240 [V]
15 [A] max. at AC 100 [V]
30 [A] max. at AC 240 [V]
※2
0.8 [A] max.
(0.8 [A] 照明使用時)
2.3 [A] max.
(2.3 [A] 照明使用時)
自然空冷 ファンによる強制空冷
※3
約 1 [kg] 約 1.1 [kg]
※4
※1
※2
※3
※4
欧州整合規格
MLEK-A080W1LRD、MLEK-A230W1LRD及びオプション品は、上記ヨーロッパ規格への適合をCEマー
キングの宣言書にて宣言しております。また本体をCE適合にて使用する場合、CEマーキングに適合した
ACケーブルをご使用ください。
使用する際には、入力するAC電圧/電流と使用する国や地域の規格に適合した適切な電源コードをご使
用ください。(オプションにて製品に添付されているケーブルの型式をご確認ください。)
(オプションのMC-AC200A-2.0MはCEマーキングに適合しております。)
Low Voltage: EN61010-1
EMC: EN55011, EN61000-3-2, EN61000-3-3, EN61000-6-2
信号出力
保護機能
環境条件
出力形態
出力調整機能
出力可変範囲
リモートコントロール
屋内使用
最高高度 : 2000 m
温度 : 0 ℃ ~ 45 ℃
湿度 : 31 ℃ まで 80 % RH、40 ℃ で 50 % RH に線形に低下
主電源電圧変動が公称電圧の ± 10 % 以内
設置カテゴリ Ⅱ
汚染度2
型式
入力電圧
入力電流
入力周波数
入力突入電流
出力数
出力電圧
出力電流
出力制御方式
ゴム足を下にした水平設置
50/60 [Hz]
AC 100 - 240 [V] (本体・ACインレット)
1チャンネル出力
0 - 100 [%]
有り 制御エラー信号
Max 12.5 [V]
DC連続出力
定電流制御
有り マニュアル/リモート
IP 30 (EN 60529)
W75×H90×D150 (突起部除く)
-20 ~ 85 [℃] / 20 ~ 85 [%RH] (結露なきこと)
有り
8ビットデジタル出力調整 / 出力ON/OFF制御
クラスⅠ機器
照明未接続時の出力シャットダウン
保護等級
外形寸法
質量
感電保護
冷却方式
保存温度/湿度
設置方法
直径2.5mm以上の物体が内部に侵入しません。水の浸入に対して保護されていません。
コールドスタート時。

9
オプション
オプション品 ピンアサイン
・KE タイプ
5 ページの標準ピンアサイン参照。
CE適合 ○:Yes
×:No
照明用中継ケーブル
(別売り)
※1 1m,2m:○
3m:× ※6
照明ファン用中継ケーブル
(別売り)
※1 1m,2m:○
3m:× ※6
AC 200 Vケーブル
(別売り)
MC-AC200A-2.0M (2mのみ) ※2 ○
AC 200 Vケーブル
(別売り)
MC-AC200B-2.0M (2mのみ) ※3 ×
AC 100 Vケーブル
(別売り)
※4 ×
外部接続ケーブル
(別売り)
MC-EXC-02 (2m・片端バラ) ※1 ○
取付ブラケット
(別売り)
LBK-001 (底面取付タイプ) -
8bitデジタル入力 KE改造
(受注生産) 『-KE』
論理反転 ※5 ○
8bitデジタル入力 AE改造
(受注生産) 『-AE』
COMMON極性反転 ※5 ○
8bitデジタル入力 AC改造
(受注生産) 『-AC』
COMMON極性反転 および 論理反転 ※5 ○
※1 長さ違いはお問い合わせください。
※2 ※3 ※4 アダプタ
(国内のみ
使用可)
CE <PS>E <PS>E/UL/CSA <PS>E
AC 250Vまで AC 250Vまで AC 125Vまで
(使用する国や地域の規格に適合したケーブルを使用してください。)
(ケーブル仕様の詳細は別途弊社までお問い合わせください。)
M-RCB4**L (4ピン用延長ケーブル)
** 2桁は長さ (01=1m、02=2m、03=3m)
M-RCB0**L (2ピン用延長ケーブル)
** 2桁は長さ (01=1m、02=2m、03=3m)
※5 表1 参照 (型式末尾に-KE/-AE/-AC)
MC-AC100A-2.0M (2mのみ)
変換アダプタ付(ACケーブル先端に取り付け)
名称 型式
※6 3m延長ケーブルはCE適合外です
表1
エラー信号
8ビット論理 8ビットオープン ON/OFF論理 ON/OFFオープン 出力形態
標準 (KC) + L 消灯 MAX点灯 L 消灯 点灯 オープンエミッタ
KE + L 点灯 消灯 L 消灯 点灯 オープンエミッタ
AC - H 消灯 MAX点灯 H 消灯 点灯 オープンコレクタ
AE - H 点灯 消灯 H 消灯 点灯 オープンコレクタ
出力(照明)の状態
※ COMMON +: 外部電源 +, COMMON -: 外部電源 -
※ 論理 H: 外部電源 +, 論理 L: 外部電源 -
Type COMMON

10
・AC/AE タイプ
オプション品 真理値表
・KE タイプ
・AC タイプ
№ 名 称 № 名 称
18bitデジタル入力 20
(
LSB
)
9COMMON (-) ※1
28bitデジタル
入力
2110 出力ON/OFF信号(入力) ※2
38bitデジタル
入力
2211 制御エラー信号出力 ※4
48bitデジタル入力 23※3 12 NC
58bitデジタル
入力
2413 NC
68bitデジタル
入力
2514 NC
78bitデジタル
入力
2615 NC
88bitデジタル
入力
27
(
MSB
)
※1
※2
※3
※4
COMMONに対し、各入力ピンは5 V から 24 Vに対応しています。
・ 使用中の入力変動は行わないでください。
”H”入力時 ・・・・・・・・・・・・・・・・・・・・・・・・・・・ 出力OFF
電流 H = 5 V時 : 1 mA 、 H = 24 V時 : 6 mA (電圧入力)
”L”(COMMON)入力またはオープン時 ・・・・・ 出力ON
・ MANU/REMOに関係なく動作します。
REMOのみ有効です。(出力の状態については真理値表を参照)
・ ”H”入力時 1回路あたりの電流 H = 5 V時 : 1 mA 、 H = 24 V時 : 6 mA (電圧入力)
エラー時 : 出力COMMONショート
オープンコレクタ出力です。
・ 4 mA 以下の電流でご使用ください。
・ MANU/REMOに関係なく出力いたします。
正常時 : 出力オープン
COARSE FINE
出力
ON/OFF
Bit
27
Bit
26
Bit
25
Bit
24
Bit
23
Bit
22
Bit
21
Bit
20出力(照明)の状態 制御
エラー
× × L ×××××××× 出力OFF ×
× × H ×××××××× 出力ON ×
× × × ×××××××× 制御エラー H
00H HHHHHHHH MIN出力 L
01H HHHHHHHL L
0 2 H HHHHHHLH L
: : : :::::::: : L
: : : :::::::: : L
F D H LLLLLLHL L
FEH LLLLLLLH L
FFH LLLLLLLL MAX出力 L
入力 H : High(COMMON)入力 または 入力オープン
L:Low 入力
出力 H : 出力 COMMONショート (カプラON)
L : 出力 オープン (カプラOFF)
× : H ・ L 任意
(COARSE,FINE) が (0,5) 程度まで点灯しない範囲があります。
出力
出力調整スイッチ 外部信号 COMMON +
COARSE FINE
出力
ON/OFF
Bit
27
Bit
26
Bit
25
Bit
24
Bit
23
Bit
22
Bit
21
Bit
20出力(照明)の状態 制御
エラー
× × H ×××××××× 出力OFF ×
× × L ×××××××× 出力ON ×
× × × ×××××××× 制御エラー L
00L HHHHHHHH MIN出力 H
01L HHHHHHHL H
0 2 L HHHHHHLH H
: : : :::::::: : H
: : : :::::::: : H
F D L LLLLLLHL H
FEL LLLLLLLH H
FFL LLLLLLLL MAX出力 H
入力 H:High入力
L : Low(COMMON)入力 または 入力オープン
出力 H : 出力 オープン (カプラOFF)
L : 出力 COMMONショート (カプラON)
× : H ・ L 任意
(COARSE,FINE) が (0,5) 程度まで点灯しない範囲があります。
出力調整スイッチ 外部信号 COMMON - 出力

11
・AE タイプ
オプション品 入出力回路例
・KE タイプ
6 ページの標準入出力回路例参照。
・AC/AE タイプ
5 V - 24 V
5 V - 24 V
A
5 V - 24 V
A
5 V
47k
1
5 V - 24 V
5 V
8
47k
MSB
3.9k
A
11
10
TransistorPhoto-coupler
Relay
COMMON
5 V, 24 V ON/OFF
Error
BB
A A
5 V, 24 V
LSB
5 V
5V = 1.3k
5 V
9
24V = 6.2k
3.9k
330
3.9k
47k
5V = 1.3k
5 V, 24 V
24V = 6.2k
5 V - 24 V
COARSE FINE
出力
ON/OFF
Bit
27
Bit
26
Bit
25
Bit
24
Bit
23
Bit
22
Bit
21
Bit
20出力(照明)の状態 制御
エラー
× × H ×××××××× 出力OFF ×
× × L ×××××××× 出力ON ×
× × × ×××××××× 制御エラー L
00L LLLLLLLL MIN出力 H
01L LLLLLLLH H
0 2 L LLLLLLHL H
: : : :::::::: : H
: : : :::::::: : H
F D L HHHHHHLH H
FEL HHHHHHHL H
FFL HHHHHHHH MAX出力 H
入力 H:High入力
L : Low(COMMON)入力 または 入力オープン
出力 H : 出力 オープン (カプラOFF)
L : 出力 COMMONショート (カプラON)
× : H ・ L 任意
(COARSE,FINE) が (0,5) 程度まで点灯しない範囲があります。
出力外部信号 COMMON -
出力調整スイッチ

12
外形寸法
図は MLEK-A230W1LRD のものです。
MLEK-A080W1LRD には、ファン・2 ピンコネクタおよび背面の空気孔は有りません。

13
7. その他
1. 装置および装置の部品は一般廃棄物として処理せずに、必ず分別してください。
2. 装置および装置の部品を廃棄する前に、処理方法または回収方法を必ず弊社までお問い合わせく
ださい。
3. 以下のシンボルは、廃電気・電子機器の分別回収を意味しています。装置および装置の部品は一般
廃棄物として処理しないでください。
4. 本装置は、2002/96/EC 指令(廃電気・電子機器の処理指令: Waste EIectrical and EIectronic
Equipment)に該当いたします。当指令においては、環境の保護・保存、人体の健康への保護、天然資源
の利用を慎重かつ合理的に行うことを最重要としています。本趣旨に基づき、取扱説明書による装置およ
び装置部品の廃棄によって、お客様が環境保全に対する責任を負うことをご承知ください。
5. 本装置は、2002/95/EC 指令(RoHS 指令)適合しております。
または
6. 装置内の危険物質は以下になります。
Lead (Pb): 15mg: Solder of Printed Wiring Boards
Lead (Pb): 15mg: Solder of Printed Wiring Boards
Lead (Pb): 15mg: Solder of Printed Wiring Boards
Lead (Pb): 15mg: Solder of Printed Wiring Boards
《MEMO 》

14
《付録》
・不明な点はご相談ください。
補修部品の詳細やアフターサービスについてご不明な点は、お買い求めの販売店または弊社営業所に
遠慮なくお問い合わせください。
・修理を依頼される場合は、次のことをお知らせください。
機 種 : MLKE-A080W1LRD / MLEK-A230W1LRD
製 造 番 号 : 本体に記載
ご 購 入 日 : 年 月 日
故 障 状 況 : 出来るだけ詳しく
お名前(法人名または個人名)、ご住所、電話番号、e-mail アドレス

15
English
Power source unit for MG-Wave constant current Illuminators
MLEK-A080W1LRD
MLEK-A230W1LRD
with or without suffix: -KE, -AE, -AC
INSTRUCTION MANUAL
- Table of Contents -
Table of Contents 15 4. Connections 19
1. Introduction 15 External Signal Connector 19
Precautions for Correct Use 16 Connector for Illuminator 21
Warranty 16 5. Maintenance 21
Confirming Package Contents 17 Troubleshooting 21
2. Features 17 6. Specifications 22
3. Installation 18 Optional Items 23
Basic System Configuration 18 Dimensions 26
Equipment Control 18 7. Others 27
Installation 19 《Appendix》 28
1. Introduction
Please read this instruction manual carefully, before starting operation. Keep this book for the whole
product lifetime, and store it in a place easily accessible.
Meanings of Warning Symbol The following warning symbol is used in this manual.
Be sure to fully understand the contents of the warning.
WARNING
This warning marking indicates a potentially hazardous situation, which can
result in hazard to the operator or damage to the unit, if the directions of this
Instruction Manual are not followed.

16
Precautions for Correct Use
WARNING
Use this product only after understanding contents of the following:
・ If using this product in combination with other apparatuses, please confirm the correctness/compatibility
of the connection with these external apparatuses (especially regarding insulation requirements).
・ If using this product in combination with other apparatuses, please confirm any standards, codes, or
regulations that apply to the combination of the apparatuses.
・ If using this product in combination with other apparatuses, please confirm that installation, connection
and use within the entire system is according to the specification of this product (as described in this
Instruction Manual) and according to those of all other apparatuses.
・ Never use the product for an application involving serious risks to life or property as long as the whole
system is not equipped with appropriate safety measures of the relevant safety category.
・ Please install this product in such a way that water cannot sprinkle into it.
・ Whenever some matter/dirt stuck to the product, please completely wipe it off, using a dry cloth.
・ This product needs periodical inspection and exchange of maintenance parts.
・ Whenever trouble occurs, please request repair to MORITEX, and do not dismantle the product by your own.
Other precautions
・ When a customer wants to scrap the product, the whole equipment has to be disposed as industrial
waste, according to laws and ordinances of the customer’s area.
・ Dimensions and Weights are reference.
・ Specifications of the product (or accessories or optional items) may be changed at any time based on
improvements and other reasons without any notice.
・ Please inquire to MORITEX about indistinct contents.
Warranty
The term of a warranty
The warranty of this product lasts for two years from the date of purchase. In case of product failure within
two years from the date of purchase, and there is no doubt on the correct utilization of the product,
according to this instruction manual the unit will be repaired at no charge.
Limitations of warranty
When inconvenience due to our responsibility occurs to a product during the warranty period, the part
that has trouble will be changed to a new part, or repaired, free of charge. But, if the cause of the trouble
fits to the following, the product is out of warranty.
・ The cause of the trouble is of such technical nature that could not be foreseen at the time of shipment.
・ The trouble is not caused by this product.
・ The trouble is caused by modification or repair by a person other than MORITEX.
・ The trouble is caused by unauthorized use, not conforming to this Instruction Manual.
・ The trouble is caused by the inappropriate handling such as a drop or a shock.
・ The trouble is repaired by MORITEX at on-site service.
・ The trouble is caused by a condition out of our responsibility such as a natural disaster or pollution.
・ The cause of the trouble can not be identified by MORITEX.
MORITEX shall not be responsible for indirect or consequential damages, in any way related to this
product. The responsibility of MORITEX for any act shall not exceed the price of this product. The
warranty is limited to business and use in Japan. Please inquire to MORITEX about warranty overseas.

17
Confirming Package Contents
Refer to Page 19: Installation, Page 22: Specifications, Page 23: Optional Items
2. Features
Applicable Illuminators
Requirements for applicable MG-Wave Illuminators (made by MORITEX) : ※1,※2
MLEK-A080W1LRD: Illuminator of up to 0.8 [A] /4pin
MLEK-A230W1LRD: Illuminator of up to 2.3 [A] /4pin or 4pin+2pin
Output
Number of output channels: 1 channel
Manual illuminance adjustment function
It is possible to adjust the illuminance of the Illuminator by using the Output Control SW on the front-panel.
※ Manual adjustment of the illuminance is possible when selecting MANU mode (MANU/REMO SW)
※ Hexadecimal control: 0,1,・・・・,E,F
※ (COARSE, FINE): (0,0) = MIN; (F,F) = MAX
※ Range between (0,0) and about (0,5) does not turn on the Illuminator.
Remote illuminance adjustment function
It is possible to adjust the illuminance of the Illuminator by inputting an 8bit digital signal to the External
Signal Connector on the rear-panel.
※ Remote adjustment of the illuminance is possible when selecting REMO mode (MANU/REMO SW)
Output ON/OFF function
It is possible to turn off the Illuminator by inputting a relevant signal to the External Signal Connector.
※ Operation of this function is possible regardless of the MANU/REMO setting.
Control error signal output function
When illuminator is not connected, the unit shuts down the output power to the Illuminator and puts out a
control error signal at the External Signal Connector.
※ This function works independent of the MANU/REMO setting.
WARNING
※1 Do not connect anything to output except designed illuminator.
※2 Please never exceed specified current values.
Part name Quantity Unit Notes
Main body 1 piece -
Power Supply Cord Set 1 piece ※
Instruction Manual 1 book This book
※ 『MC-AC100A-2.0M』 is attached to 『-100V』 model. 『MC-AC200A-2.0M』 is attached
to 『-200V』 model. (It depends on the suffix of the model that was purchased.)
Before connection to the power supply, please check the conformity of the specifications
of the Power Supply Cord Set with the laws and standards of your country as well as the
correct power and temperature rating.

18
3. Installation
Basic System Configuration
・ This Unit is dedicated for use with/for connection to the MG-Wave Illuminator.
・ For external control, it is possible to connect an external apparatus via the External Signal Connector.
※ MLEK-A230W1LRD unit has an additional connector for the fan of the Illuminator.
※ The cables for connection to the EXT Connector and to the Illuminator and to the Fan of the
Illuminator are supplied as Optional Item (MC-EXC-02, M-RCB4**L, M-RCB0**L).
Equipment Control
① Power SW Tilt to "I" side for turning on power.
② Power Indicator LED illuminates when power supply is ON.
③ MANU/REMO SW Switch for selecting manual or remote control.
④ Output Control SW Manual adjustment switch for output-control.
⑤ Connector for Illuminator: OUT Terminal for connection to the Illuminator.
⑥ Connector for Fan of Illuminator: FAN Terminal for connection to the fan of the Illuminator.
⑦ Cooling-Fan Air inhaling type fan for cooling unit interior.
⑧ External Signal Connector: EXT Terminal for external control.
⑨ MAINS supply Inlet for connecting power supply cable.
⑩ Air Hole Air hole for cooling forced by Fan (air-exhalation).
⑪ Rubber Feet Take them off, when using with the optional installation bracket.
※ Drawings show the MLEK-A230W1LRD unit.
※ MLEK-A080W1LRD does not have ⑥,⑦.

19
Installation
Install horizontally on the rubber feet at the bottom of the unit.
※ Install the unit in such a way, that adequate space is left free for ventilation. Keep space of at least
10mm around the main body.
※ Be sure to install the unit in such a way that the Power Switch can be operated easily and the Mains
Plug can be pulled out without hindrance, in case of emergency.
※ Protection Class: Class I equipment
※ Before using this product, please provide an appropriate power supply cord set conforming to the
input power ratings and to the relevant standards of the area where you use this product.
※ The power supply cord set shall have following configurations:
Length: < 3 m; Conductors: L / N / PE; Class I type mains plug with reliable connection to the
Protective Earthing Conductor of the Building Installation.
Optional Item MC-AC200A-2.0M does comply with these requirements.
4. Connections
WARNING
・Only SELV circuits, which have reinforced insulation to their equipment
primary circuit, may be connected to the unit.
・For connection to the External Signal Connector, use a shielded cable with
a recommended length of less than 2 m (Optional item: MC-EXC-02)
・Please do not excessive input or overload.
External signal connector (EXT)
Model
Pin assignment
№ Identification № Identification
18bit di
g
ital in
p
ut 20
(
LSB
)
9 COMMON (+) ※1
28bit di
g
ital in
p
ut 2110 Input ON/OFF signal ※2
38bit di
g
ital in
p
ut 2211 Control error signal output ※4
48bit di
g
ital in
p
ut 23※3 12 NC
58bit di
g
ital in
p
ut 2413 NC
68bit di
g
ital in
p
ut 2514 NC
78bit di
g
ital in
p
ut 2615 NC
88bit di
g
ital in
p
ut 27
(
MSB
)
※1
※2
※3
※4
・ Function regardless of MANU/REMO selection
Only for REMO Control (Refer to Truth Table, shown below)
Normal Condition (no errors detected): Open Circuit
Input ”H”(COMMON) or Input open ・・・・・ Output ON
・ Open-Collector type input is possible.
Current: 1 mA (Common: 5 V), 6 mA (Common: 24 V)
Input ”L” ・・・・・・・・・・・・・・・・・・・・・・・・・・・ Output OFF
・ Please use signal with current equal or less than 4 mA.
It is possible to input a voltage between 5V and 24V.
Control Error detected: Output short circuited to COMMON
・ Please do not change the input voltage during operation.
Open-Emitter type output with following characteristics:
・ Open-Collector type input is possible.
・ Operation possible regardless from MANU/REMO selection.
・ Input “L”, Current per circuit: 1 mA (Common: 5 V), 6 mA (Common: 24 V)
HDAB-15S(05) : connector(female) (made by HRS)
HDA-CTH : connector case (made by HRS)
Terminal of the Unit Connector of the cable
HDAB-15P(05)(male)
(made by HRS)
Screws: M2.6 or its equivalent

20
Truth table
Example of input and output circuit
5 V
47k
1
5 V - 24 V
8
5 V
47k
MSB
3.9k
A
10
11
Photo-couplerRelay Transistor
5 V, 24 V
ON/OFF
COMMON
Error
A
A
BB
A A
5 V, 24 V
LSB
5 V
5V = 1.3k
5 V
9
24V = 6.2k
3.9k
330
3.9k
47k
COARSE FINE
Output
ON/OFF
Bit
2
7
Bit
2
6
Bit
2
5
Bit
2
4
Bit
2
3
Bit
2
2
Bit
2
1
Bit
2
0
State of output
(Illuminator)
Control
Error
× × L ×××××××× Output OFF ×
× × H ×××××××× Output ON ×
× × × ×××××××× Control Error H
00H LLLLLLLL Output MIN L
01H LLLLLLLH L
0 2 H LLLLLLHL L
: : : :::::::: : L
: : : :::::::: : L
F D H HHHHHHLH L
FEH HHHHHHHL L
FFH HHHHHHHH Output MAX L
Input H : Input High(COMMON) or Input open
L : Input Low
Output (Control Error) H : Short Circuit to COMMON (Photo-coupler ON)
L : Open Circuit (Photo-coupler OFF)
× : H ・ L state not relevant
(COARSE,FINE): Range between (0,0) and about (0,5) does not turn on the Illuminator.
OutputExternal signals COMMON +
Output control SW
This manual suits for next models
1
Table of contents