Morphy Richards Precise Steam Plus User manual

g
∂
Precise Steam Iron steam/spray shot
Please read and keep these instructions
Jemné žehlení s napařováním/výstřik páry
řečtěte si tyto pokyny a uschovejte je
40730MCZ Rev1:9225 47507 MEE pump - Jon 10/10/08 16:02 Page 1

2
IMPORTANT
SAFEGUARDS
When using your flatiron, basic
safety precautions should always be
followed, including the following:
• READ ALL INS RUC IONS
BEFORE USING.
1Use iron only for its intended use.
2To protect against a risk of electric
shock, do not immerse the iron,
cord or plug in water or other
liquids.
3The iron should always be turned to
‘Off’ before plugging or unplugging
from outlet. Never yank cord to
disconnect from outlet; instead,
grasp plug and pull to disconnect.
4Do not allow cord to touch hot
surfaces. et iron cool completely
before putting away. oop cord
loosely around iron when storing.
5Always disconnect iron from
electrical outlet when filling with
water or emptying and when not in
use.
6Do not operate iron with a damaged
cord or if the iron has been
dropped, damaged or leaking. To
avoid the risk of electric shock, do
not disassemble the iron, take it to a
qualified serviceman for
examination and repair. Incorrect
reassembly can cause a risk of
electric shock when the iron is
used.
7Close supervision is necessary for
any appliance being used by or near
children.
8Do not leave iron unattended while
connected or on an ironing board.
9Burns can occur from touching hot
metal parts, hot water, or steam.
Use caution when you turn a steam
iron upside down – there may be
hot water in the reservoir.
10This appliance is not intended to be
used by young children or infirm
persons unless they have been
adequately supervised by a
responsible person to ensure they
can use the appliance safely.
11Young children should be
supervised to ensure that they do
not play with the appliance.
Other safety
consi erations
•Always locate your iron away from
the edge of the worktop/ironing
board.
• Ensure that the iron is used on a
firm, flat surface.
• Do not use the iron in a bathroom.
•WARNING: Do not place the iron
onto a metal tray or metal
surface whilst in use.
• Do not touch hot surfaces, use
handles or knobs.
• Do not fill above the MAX mark,
otherwise water may be ejected.
• Allow to cool before putting on or
taking off parts and before cleaning.
• Do not use outdoors.
• Do not place the iron on or near a
hot gas or electric burner or in a
heated oven.
• Do not use the vertical steam on
clothes being worn.
• Always disconnect the iron from the
electrical socket when filling with
water or emptying and when not in
use.
• When placing the iron on its heel,
ensure that the surface on which
the heel is placed is stable.
Treating scal s
• Run cold water over the affected
area immediately. Do not stop to
remove clothing, get medical help
quickly.
g
40730MCZ Rev1:9225 47507 MEE pump - Jon 10/10/08 16:02 Page 2

3
g
Electrical requirements
Check that the voltage on the rating
plate of your appliance corresponds
with your house electricity supply
which must be A.C. (Alternating
Current).
WARNING: his appliance must
be earthed.
UK only
If the socket outlets in your home
are not suitable for the plug
supplied with this appliance, the
plug should be removed and the
appropriate one fitted.
WARNING: he plug removed
from the mains lead, if severed,
must be destroyed as a plug
with bared flexible cord is
hazardous if engaged into a live
socket outlet.
Where used, should the fuse in the
13 amp plug require changing, a 13
amp BS1362 fuse must be fitted.
WARNING: his appliance must
be earthed.
Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the
International Textile Care abelling Code.
Symbol
(120˚C Max) Cool (160˚C Max) Warm (210˚C Max) Hot
Control knob
positions
Do not iron
at all
Fabric Nylon, Acetates
e.g. Acrilan
Courtelle, Orlon
Triacetates, e.g.
Tricel/ olyester
Wool, olyester
mixtures e.g.
olyester/Cotton
Cotton, Linen
Rayon, Rayon
mixtures,
e.g. Rayon/Linen
Ironing Iron on wrong side
if moisture required
use damp cloth
(Not Acetate)
Fabrics requiring this
setting usually require
steam pressing for heavy
cotton, denim etc.
With water in tank Dry and spray Steam/spray/
shot of steam
Without water in tank Dry ironing
‘Max setting’
Self clean
INSTRUCTIONS FOR USE
Temperatre guide
40730MCZ Rev1:9225 47507 MEE pump - Jon 10/10/08 16:02 Page 3

4
Getting the best from your
new iron....
Safety first
Caution must be used when
handling this appliance as it does
get very hot. Always switch off the
unit and allow to cool before
cleaning or storing.
Self cleaning button
Your iron will give the best ironing
results and will last longer if you use
the self clean feature at least once a
month.
COMPONENTS OF
OUR IRON
⁄Steam to dry iron selector switch
¤Temperature control dial
‹Steam level indicator window
›Spray button
fiShot of steam button
flTemperature indicator light
‡Water tank
(illuminated certain models)
·Soleplate
‚Self-clean button
„Spray nozzle
‰Filling hole with cap
ÂFiller cup (300ml)
BEFORE USE
Sort out the items to be ironed
according to the type of fabric. This
will minimise the frequency of
temperature adjustment for different
garments.
Note: The steam facility should only
be used on garments which are
suitable for ironing at the 2 and 3
dot settings.
Textiles and clothes are supposed
to carry ironing instructions. If they
don’t you should follow the fabric
guide on page 3, but be sure to test
the temperature by ironing the hem
of the garment or similar area first.
If you turn the control dial down
from a hot setting to a cooler
setting, wait until the iron
temperature has stabilised before
you continue ironing.
Delicate fabrics such as silk,
wool,velour, etc, are best ironed
with an ironing cloth to prevent
shine marks.
fl
‡
·
‚
„
⁄
¤‹›
Â
400
350
300
40730MCZ Rev1:9225 47507 MEE pump - Jon 10/10/08 16:02 Page 4

5
FILLING A
1Make sure that the iron is not
plugged in, then set the steam to
dry iron selector switch ⁄to
the ‘0’ position before filling the iron
with water.
2ift up the filler cap and fill the tank
‡with water through the filling hole
‰, using the beaker provided
(300ml). A Â After filling replace
the filler cap. In hard water areas
the use of distilled or demineralised
water is recommended.
WARNING: Never use battery
topping up fluid or water
containing any substances like
starch, or sugar, or defrosted
water from a refrigerator.
3Always pour out the remaining
water after use.
WARNING: When filling your iron
with tap water always use the
beaker provided. Never fill
directly under the tap.
TEMPERATURE
CONTROL B
Plug in the iron and switch on. Set
the temperature control dial ¤to
the temperature required, but don’t
start ironing immediately.
If you wait a few minutes, the iron
will stabilise at the required setting.
Your Morphy Richards iron is fitted
with an indicator light flwhich will
go on and off while you are ironing.
This is perfectly normal as it shows
that the iron is maintaining the heat
setting you have chosen.
It is always a good idea to begin
with cool fabrics and work up to
higher settings.
An iron heats up quicker than it
cools down so you’ll save time and
electricity.
FEATURES OF OUR
IRON
Temperature in icator
light
The indicator light flshows that
the iron is warming up. When the
required temperature is reached the
light will go out and will cycle on-off
during operation.
Dry ironing
You can use your iron as a dry iron
only. Make sure the steam to dry
iron selector switch ⁄is set to the
symbol.
Any temperature setting may be
used depending on the garment.
The spray feature may be used
provided there is water in the tank
(see filling section). You do not need
to put any water in the tank when
dry ironing only.
Spray C
Press the spray button ›and aim
the spray of water at stubborn
creases. You can do this whilst dry
ironing providing there is water in
the tank. When using the water
spray it may be necessary to push
the button a few times to get the
spray pump primed.
Automatic variable
steam D
Fill the iron with water as described
in the filling section, and insert the
plug into the electrical socket.
1Set the steam to dry iron selector
switch to steam.
2Select the temperature required by
turning the temperature control dial
¤to the desired setting. The
amount of steam required is
automatically selected and is
displayed in window ‹.
Press the shot of steam button fi
to obtain a burst of extra steam for
ironing out creases in heavy
material such as denim.
g
A
B
C
D
40730MCZ Rev1:9225 47507 MEE pump - Jon 10/10/08 16:02 Page 5

6
The shot of steam can be used
whilst dry ironing, providing there is
water in the tank, and the
temperature control is set within the
steam range.
Do not use shot of steam at
temperatures below the steam
range (1-DOT) shown on the control
dial.
Note: For optimum steam quality,
do not operate the shot more than
three times in succession.
Vertical steam
Hold the iron in a vertical position
between 1cm and 2cm away from
the item E. Press the shot of steam
button fi, this will create vertical
steam. This feature is especially
useful for removing creases from
hanging clothes, curtains, wall
hanging, etc.
Note; For optimum steam quality,
do not operate the shot more than
three times in succession.
No rip system
Your iron is fitted with a no drip
system which is designed to
prevent water escaping from the
soleplate when the iron is too cold.
During use, the no drip system may
emit a loud click, particularly during
heat-up or whilst cooling down. This
is perfectly normal and indicates
that the system is functioning
correctly.
Auto shut-off
(certain models only)
If your iron is fitted with the auto
shut-off function it will automatically
shut down after a set period.
If the iron is left unattended in the
horizontal position it will shut down
after 1 minute. When this occurs,
the indicator light will flash and a
beep will be heard.
If it is left in the vertical position it
will shut down after 8 minutes.
To reactivate the iron gently shake
it, the temperature indicator light will
come on indicating the iron is
warming up and wait for the iron to
heat-up as normal.
LIFE LONG ANTI- SCALE
S STEM (certain models only)
The life long anti-scale system
reduces scale deposits and helps
prolong the life of the iron.
EMPT ING AND
STORING
When you have finished ironing,
unplug your iron. Ensure that the
steam to dry iron selector switch ⁄
is set at the position, lift up the
fill cap and empty any remaining
water out of the filling hole F.
Do not store in the box, but in an
upright position, so that any drops
of water remaining cannot leak out
and discolour the soleplate G.
Important: The flex can be damaged
if wound too tightly around the iron
after use. Make a loose loop with
the flex and wrap it around the iron.
The iron must be cool before
winding the flex and storing on its
heel.
MAINTENANCE
Self clean feature
1Half fill the iron with water.
2Place the iron on its heel.
3Connect to a mains supply outlet
4Turn the temperature dial to ‘MAX’
setting
5The pilot light will glow indicating
the irons switched on.
6The pilot light will go off when the
required temperature is reached.
7Wait for one more cycle;
(pilot light glows and goes off.)
8Turn the temperature dial in anti-
clockwise direction to ‘Min’
E
F
G
40730MCZ Rev1:9225 47507 MEE pump - Jon 10/10/08 16:02 Page 6

7
9Disconnect the iron from mains
supply outlet.
10 Hold the iron horizontally over
a sink.
11 Press and hold down the Self-
Cleaning button.
12Steam and boiling hot water will
drain from the holes in the the
soleplate washing away the scale
and minerals that have built up
inside the Steam Chamber.
13Gently move the iron back and forth
until the water tank is empty.
14 When Self-Cleaning is complete,
release the Self-Cleaning button.
15 Rest your steam iron back on its
heel and allow to fully cool down.
16 Wipe the soleplate with a cold
damp cloth.
WARNING: Keep hands and
body away from the hot water.
WARNING: Do not attempt to
descale the soleplate with
descaling products.
To clean a stainless
steel soleplate
To keep the soleplate of your iron
clean and free of limescale, we
recommend that you use one of the
gentle chrome, silver or stainless
steel cleaners that are generally
available. Always follow the
manufacturers instructions. To clean
off melted man-made fibres set the
iron at 3 dot position and pass it
over a clean piece of cotton which
will draw the deposit off the surface.
To clean a coate
soleplate (certain models only)
In the unlikely event of any man-
made fibre fusing to the soleplate,
set the iron at the 3 dot position and
pass it over a clean piece of cotton
which will draw the deposit off the
surface.
Do not use scouring powder or
solution as this could cause
damage to the coating.
To clean the exterior
Allow the iron to cool and wipe over
with a damp cloth and mild
detergent, then wipe with a dry
cloth.
g
40730MCZ Rev1:9225 47507 MEE pump - Jon 10/10/08 16:02 Page 7

8
OUR TWO EAR
GUARANTEE
It is important to retain
the retailers receipt as proof of
purchase. Staple your receipt to this
back cover for future reference.
Please quote the following
information if the product develops
a fault. These numbers can be
found on the base of the product.
Model no. Serial no.
All Morphy Richards products are
individually tested before leaving the
factory. In the unlikely event of any
appliance proving to be faulty within
28 days of purchase it should be
returned to the place of purchase
for it to be replaced.
If the fault develops after 28 days
and within 24 months of original
purchase, you should contact the
Helpline number quoting Model
number and Serial number on the
product, or write to Morphy
Richards at the address shown. You
may be asked to return a copy of
proof of purchase.
Subject to the exclusions set out
below (see Exclusions) the faulty
appliance will then be repaired or
replaced and dispatched usually
within 7 working days of receipt.
If for any reason this item is
replaced during the 2 year
guarantee period, the guarantee on
the new item will be calculated from
original purchase date. Therefore it
is vital to retain your original till
receipt or invoice to indicate the
date of initial purchase.
To qualify for the 2 year guarantee
the appliance must have been used
according to the manufacturers
instructions. For example kettles
should have been regularly
descaled.
EXCLUSIONS
Morphy Richards shall not be liable
to replace or repair the goods under
the terms of the guarantee where:
1The fault has been caused or is
attributable to accidental use,
misuse, negligent use or used
contrary to the manufacturers
recommendations or where the fault
has been caused by power surges
or damage caused in transit.
2The appliance has been used on a
voltage supply other than that
stamped on the products.
3Repairs have been attempted by
persons other than our service staff
(or authorised dealer).
4Where the appliance has been used
for hire purposes or non domestic
use.
5Morphy Richards are not liable to
carry out any type of servicing work,
under the guarantee.
6Plastic filters for all Morphy
Richards kettles and coffee makers
are not covered by the guarantee.
This guarantee does not confer any
rights other than those expressly set
out above and does not cover any
claims for consequential loss or
damage. This guarantee is offered
as an additional benefit and does
not affect your statutory rights as a
consumer.
40730MCZ Rev1:9225 47507 MEE pump - Jon 10/10/08 16:02 Page 8

9
AUSTRALIAN WARRANTY
This appliance is guaranteed for 2
years against faulty material,
components and workmanship.
This warranty is in addition and
does not affect your statutory rights.
Proof of purchase must be
produced for any warranty benefit.
In the unlikely event of any
appliance proving to be faulty,
securely pack and return the item to
the place of purchase accompanied
by the original receipt or invoice.
NOT COVERED B THIS
WARRANT (Australian only)
• If the appliance has not been used
in accordance with the
manufacturers’ recommendations or
Instructions.
• If the fault is deemed to be caused
by abuse, misuse, neglect,
modifications or in proper use and
or care
Eg: Kettles: Excessive build up of
scale.
Toasters: Excessive build up of
crumbs or foreign matter etc.
• Connection to incorrect voltage to
that stamped on the product
• Unauthorised repairs
• Appliance used other than for
domestic purposes.
• Excluding bags, filters, glass,
carafes, and cutting blades.
• Freight and insurance costs.
If for any reason this item is
replaced during the 2 year
guarantee period, the guarantee on
the new item will be calculated from
original purchase date. Therefore it
is vital to retain your original receipt
or invoice to indicate the date of
original purchase.
Morphy Richards’s policy is to
continually improve quality design
and product quality. The company
therefore reserves the right to
change any specifications or to
carry out modifications as deemed
worthy at any time.
The Australian supplier ASKO
Appliances reserves the right to
repair, modify, exchange or replace
the faulty appliance with the same
or similar model or product of
equivalent value.
g
40730MCZ Rev1:9225 47507 MEE pump - Jon 10/10/08 16:02 Page 9

10
Důležité bezpečnostní
pokyny
ři používání žehličky se musí vždy
dodržovat základní bezpečnostní
opatření včetně následujících:
•PŘED POUŽITÍM SI
PROSTUDUJE VŠECHNY
POKYNY.
1oužívejte žehličku pouze k účelu,
ke kterému je určena.
2Nevkládejte ani neponořujte
žehličku, kabel ani zástrčku do nebo
ani jiné tekutiny, abyste se chránili
před rizikem úrazu elektrickým
proudem.
3řed odpojením žehličky ze zásuvky
by vždy měla být vypnutá. ři
odpojování ze zásuvky nikdy
netahejte za kabel, místo toho
uchopte zástrčku a vytáhněte ji.
4Zabraňte styku kabelu s horkými
povrchy. řed odložením nechte
žehličku úplně vychladnout. řed
uložením oviňte kabel volně kolem
žehličky.
5ři plnění vodou nebo
vyprazdňování a když žehličku
nepoužíváte, vždy ji odpojte od
elektrické zásuvky.
6Nepoužívejte žehličku s
poškozeným kabelem, nebo pokud
byla upuštěna nebo je poškozená
nebo netěsní. Nedemontujte
žehličku, předejte ji kvalifikovanému
servisnímu technikovi ke kontrole a
opravě, vyhnete se tak úrazu
elektrickým proudem. Nesprávná
montáž může způsobit riziko úrazu
elektrickým proudem při používání
žehličky.
7ři používání jakéhokoliv spotřebiče
v blízkosti dětí je nutný přísný dozor.
8Nenechávejte žehličku bez dozoru,
jestliže je připojená k síti nebo na
žehlicím prknu.
9ři kontaktu s horkými kovovými
částmi, horkou vodou nebo párou
mohou vzniknout popáleniny. ři
obracení žehličky vzhůru nohama
bud’te opatrní, v nádrži na vodu
může být horká voda.
10Tento spotřebič není určen k
používání malými dětmi nebo
nemohoucími osobami bez
náležitého dozoru zodpovědné
osoby, která zaručí, že jej mohou
bezpečně používat.
11Na malé děti se musí dohlížet, aby
bylo jisté, že si se spotřebičem
nebudou hrát.
Další bezpečnostní
pokyny
•Vždy umisťujte žehličku dále od
okraje pracovní plochy/žehlicího
prkna.
• Ujistěte se, že žehlička je používána
na pevném, rovném povrchu.
• Nepoužívejte žehličku v koupelně.
•VAROVÁNÍ: Během používání
nepokláde te žehličku na kovový
tác nebo kovový povrch.
•Nedotýkejte se horkých povrchů,
používejte držadla nebo ovládací
prvky.
• Neplňte žehličku nad značku MAX,
jinak by mohla vystříknout vařící
voda.
• řed vkládáním nebo odstraňováním
součástí a před čištěním nechte
žehličku vychladnout.
• Nepoužívejte venku.
• Neumisťujte žehličku na horký
plynový nebo elektrický vařič, do
jeho blízkosti nebo do trouby.
• Nepoužívejte svislé napařování na
oděvech oblečených na osobách.
• ři plnění vodou nebo
vyprazdňování, nebo když žehličku
nepoužíváte, vždy ji odpojte od
elektrické zásuvky.
• ři pokládání žehličky na patu se
ujistěte, že povrch, na kterém pata
stojí, je dostatečně stabilní.
Ošetření opařenin
•Zasažené místo ihned vložte pod
tekoucí studenou vodu. Nezdržujte
se svlékáním oděvu, ihned
vyhledejte lékařskou pomoc.
∂
40730MCZ Rev1:9225 47507 MEE pump - Jon 10/10/08 16:02 Page 10