Morphy Richards Saturn IntelliTemp 305003 User manual

R 305003 MUK Rev1
* Register at www.morphyrichards.co.uk/support
UK and Ireland customers only
Please read and keep these instructions for future use
IMPORTANT: To reduce limescale damage, we recommend the use of distilled,
deionised or demineralised water. This is particularly important if you live in a hard
water area.
Never use battery topping up fluid or water containing any substances like starch,
sugar, fragrant additives or defrosted water from a refrigerator.
Failure to maintain your iron will invalidate your guarantee.
If you experience any problems with this iron, do not return to the store.
Please contact our help line who will be happy to help:
We do stock spare filler lids for this iron, so if you need a replacement please call 0344 873 0710.
U : 0344 871 0944 IRE: 1800 409 119
Register your guarantee online: www.morphyrichards.co.uk/support
We'll keep you updated with special offers, competitions and important product information.
Pressurised Steam Iron with Pure
RN305003 MUK Rev1.qxp_IB 13/03/2019 11:45 Page 1

2
The use of any electrical appliance requires the following common sense safety rules.
Please read these instructions carefully before using the product.
Important safety instructions
•WARNING: Disconnect from the mains supply
before carrying out any routine maintenance.
•WARNING: Misuse of the appliance could cause
personal injury.
•
This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience or knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the
hazards involved.
•Children shall not play with the appliance.
•
Cleaning and user maintenance shall not be made
by children without supervision.
•
Keep the iron and its cord out of reach of children
less than 8 years of age at all times.
•The iron must not be left unattended while it is
connected to the supply mains.
•The plug must be removed from the socket before
filling the iron with water.
•The iron must be used and rested on a stable
surface.
•When placing the iron on its heel, ensure that the
surface on which the heel is placed is stable.
•The iron is not to be used if it has been dropped, if
there are visible signs of damage or it is leaking.
•The filling aperture must not be opened during use.
•Do not operate with a damaged grommet, it must
be replaced by the manufacturer, its service agent
or similarly qualified person in order to avoid a
hazard.
RN305003 MUK Rev1.qxp_IB 13/03/2019 11:45 Page 2

3
• CAUTION - HOT: Burns can occur from
touching hot parts.
• WARNING: Do not discharge the steam
towards people or animals. Danger of
scalding.
•WARNING: To avoid electric shock, do not
immerse appliance in water / liquid.
Electrical requirements and mains cable
•Check that the voltage on the rating plate of your
appliance corresponds with your house electricity
supply which must be A.C. (Alternating current).
•Do not let the mains lead come into contact with the
hot soleplate of the iron.
•Should the fuse in the mains plug require changing,
a 13 amp BS1362 fuse must be fitted.
•WARNING: This appliance must be earthed.
PLEASE READ ALL INSTRUCTIONS AND EEP
FOR REFERENCE
Important safety instructions ........................................................
Electrical requirements ..................................................................
Steam iron overview / Features .....................................................
Digital display overview ...................................................................
Temperature guide ..........................................................................
Before first use ................................................................................
Location ...........................................................................................
Usage tips ........................................................................................
Using the iron ..................................................................................
Features ...........................................................................................
Maintaining your iron ......................................................................
Troubleshooting ..............................................................................
Guarantee ........................................................................................
Contact us .......................................................................................
Contents
2
3
4
5
6
6
6
6
7 & 8
9
10
11
12
12
RN305003 MUK Rev1.qxp_IB 13/03/2019 11:46 Page 3

4
(1) Eco steam button
(2) Turbo steam button
(3) Power button
(4) Water spray button
(5) Crease light button
(6) Power cord
(7) Controls
(8) Iron handle
(9) Cable pivot
(10) Digital display (see page 5)
(11) Steam trigger
(12) Filling cap
(13) Self clean button
(14) Iron heel
(15) Crease light
(16) Water spray nozzle
(17) Water tank
(18) Soleplate
Steam iron overview
10
12
15
16
6
13
98
11
17
18
7
14
12
3 4 5
RN305003 MUK Rev1.qxp_IB 13/03/2019 11:46 Page 4

5
Digital display (10) overview
Steam level indicators (19/20)
The steam level indicators change when you
select your desired steam level.
IntelliTemp setting indicator (21)
This stops flashing when the product has
reached the default temperature, allowing the
appliance to iron all ironable fabrics without the
temperature needing to be adjusted.
Steam active indicator (22)
The steam active indicator illuminates and
flashes when steaming is in operation (when
either Eco or Turbo steam is selected).
Self Clean indicator (23)
This indicator will illuminate when the system
requires cleaning.
Auto shut-off indicator (24)
This indicator illuminates if the appliance has
entered auto shut-off mode after not being
used or moved for 1 minute if sat horizontally,
or 8 minutes if stood upright on its heel.
22
Steam active
indicator
19
Eco setting
indicator
23 Self clean
indicator 24 Auto shut-off
indicator
21
IntelliTemp
setting indicator
20
Turbo setting
indicator
RN305003 MUK Rev1.qxp_IB 13/03/2019 11:46 Page 5

6
The steam iron is equipped with IntelliTemp technology, which means it is safe to use on all ironable fabrics
without adjusting the temperature setting.
Do not use on fabrics that have the ‘Do ot Iron’ Symbol.
For stubborn creases, a turbo steam setting is available.
Temperature guide
Symbol Do not iron
Fabric Synthetics: Spandex or
elastane, or prints on
garments
All ironable fabrics Linen
Steam level setting
(see step 3 of
‘Using the iron’
on page 7)
Low High
With water in tank
Without water in tank
Steam/shot of steam
Dry and spray
Dry ironing
Remove all packaging and any protective cover from the soleplate (18), if any. Unwind and straighten the
power cord (6).
We recommend for first time ironing that you iron over an old towel.
Stand the iron on its heel (14) and locate it on the iron rest plate of your ironing board (if large enough) or
on a heat resistant stand at the same height as your ironing board or below it. Always ensure the iron is on
a firm surface when ironing.
WARNING: Do not use the product on a surface which could be damaged by heat or steam such as
a worktop or a polished wood surface.
If in doubt, contact Morphy Richards.
Unwind and straighten the power cord (6).
Textiles and clothes carry ironing instructions. If not, follow the temperature guide above, but test the
temperature by ironing the hem of the garment or other discreet area first.
Location
Usage tips
Before first use
RN305003 MUK Rev1.qxp_IB 13/03/2019 11:46 Page 6

WARNING: eep hands and body away from the hot soleplate (18).
7
Using the iron
1) Filling the tank
Make sure the iron is not plugged in. Fill the water tank (17) via the filling hole to the MAX graphic on
the side of the water tank, this shows the MAX level of water that the tank can hold and should be
checked whilst filling and the iron is tilted.
TO PROLONG THE LIFE OF THIS IRON, WE RECOMMEND THE USE OF DISTILLED, DEIONISED
OR DEMINERALISED WATER, ESPECIALLY IN HARD WATER AREAS.
Never use battery topping up fluid or water containing any substances like starch, sugar,
fragrant additives or defrosted water from a refrigerator.
OTE: Please see point 2 of ‘Exclusions’ on page 12.
Re-filling during use
If the water level is too low, the unit will not produce steam. If this happens, open the filling cap (12)
and refill with water.
To activate Eco steam, ensure the iron is in a
horizontal position i.e. soleplate (18) facing
downwards. Then press the Eco steam button
(1). The steam level indicator will flash and
steam will be released from the soleplate.
When the iron is rested on its heel (14) it will
pause the steam flow, this is to conserve water
in the tank. Once you resume ironing, the
continuous steam will automatically re-activate.
If the steam flow doesn't reactivate, firstly
check there is sufficient water in the tank, then
secondly put the iron in a horizontal position
and press the Eco Steam button again.
2) Switching on and IntelliTemp setting 3) Selecting Eco Steam
Plug the appliance into a mains outlet, a beep will
be heard and the product will automatically
switch on.
The IntelliTemp setting indicator (21) on the
digital display (10) will flash until the default
IntelliTemp temperature setting is reached, at
which point the IntelliTemp setting indicator will
remain constant and two beeps will be heard. The
IntelliTemp setting allows the appliance to iron all
ironable fabrics without the temperature needing
to be adjusted. However, do not iron any fabric
with this symbol .
RN305003 MUK Rev1.qxp_IB 13/03/2019 11:46 Page 7

8
To help remove stubborn creases, you may
use the water spray function. Aim the water
spray nozzle (15) at the difficult area on the
garment and firmly press and hold the water
spray button (4).
Pressing the water spray once will dispense a
set amount of water.
Using the iron (continued)
6) Water spray
When you have finished ironing, turn off the
appliance by pressing and holding the power
button (3) for 2-3 seconds. All indicators on the
digital display (10) will switch off.
To switch the product back on, press the power
button again. Alternatively, disconnect the plug
from the mains outlet if your ironing session is
complete.
7) Switching off
For more difficult ironing tasks, activate Turbo
steam by pressing the Turbo steam button (2).
The functionality is the same as Eco steam in the
previous step, but with a stronger steam flow.
4) Selecting Turbo Steam
The steam boost function is ideal for relaxing
the fibres of tougher fabrics (like jeans and
linen) and getting rid of those stubborn, hard
to reach creases.
To produce an extra boost of steam during
ironing, press the steam trigger (11).
OTE: For optimum steam quality, do not
operate the shot more than three times in
succession .
5) Steam boost
11
RN305003 MUK Rev1.qxp_IB 13/03/2019 11:46 Page 8

9
Features
Crease light
To enable clearer vision in difficult to see areas,
press the crease light button (5) to switch on the
crease light (15), press again to switch off.
Dry ironing
To use your iron as a dry iron only, follow step 2
of ‘Using the iron’ on page 7. Do not press the
eco steam button (1) or the turbo steam button
(2) to operate the steam pump. You do not need
to put water in the water tank (17).
Vertical steam
Vertical steam is useful for removing creases from
dry clean only items, delicate clothing, curtains
and upholstery, etc.
To activate the steam for vertical steaming, hold
the iron vertically and press the
eco steam button
(1) or the turbo steam button (2) . The steam level
indicator will flash to show when the iron is
steaming. Simply allow the steam to pass lightly
over the garment (at a distance of between 1cm
and 2cm away from the item) to gently remove
creases and freshen up the fabric. To conserve
water in the tank, the steam flow will
automatically stop when the iron is rested on its
soleplate
(18) . You will need to press the eco
steam button (1) or the turbo steam button (2)
again if you want to continue vertical steaming.
To generate a steam boost for stubborn creases,
press the steam trigger
(11) .
WARNING: Do not use the vertical steam
feature on clothes that are being worn.
Auto shut-off
If the iron is not moved or any buttons on the
controls (7) are unused for 1 minute if sat
horizontally, or 8 minutes if stood upright on its
heel, the product will automatically turn off for
safety and to save energy. When this happens,
the auto shut-off indicator (24) will flash and beep
once.
To restart, either move the iron or press any
buttons on the controls (7) and wait for the
temperature to rise again.
OTE: The appliance is not turned off completely
in auto shut-off mode. To switch the product off,
press and hold the power button
(3) until all
indicators in the digital display (10) extinguish,
then unplug the product from the mains outlet.
11
RN305003 MUK Rev1.qxp_IB 13/03/2019 11:46 Page 9

10
Emptying and storing
When you have finished ironing, p ress and hold
the power button (3) to switch the product off,
then unplug and empty all water from your iron.
When cool, store the iron on its heel
(14) with the
power cord
(6) wrapped loosely around the heel.
OTE: Please see point 4 of ‘Exclusions’ on page
12
.
Cleaning the soleplate
To clean a coated soleplate
Do not use scouring powder or solution as this
could cause damage to the coating.
If any man-made fibres fuse to the soleplate (18),
set the iron at the MAX setting and pass it over a
clean piece of cotton to draw the deposit off the
surface.
To clean the exterior
Allow the unit to cool and wipe over with a damp
cloth and mild detergent, then wipe dry.
Removing limescale
Y our iron has a built in self clean system
designed to keep the water valve, steam
chamber and steam vents clear of lint and
loose mineral deposits.
When the self clean indicator (23) appears on the
digital display (10), the self clean function must
be operated.
1Half fill the iron with water.
2Connect to a mains supply outlet.
3Wait for the temperature to be reached - the
IntelliTemp setting indicator (21) with illuminate
constantly.
4P ress and hold the power button (3) to switch
the product off .
5Disconnect the iron from the mains supply outlet.
6Whilst the iron is still very hot, hold the iron
horizontally over a sink.
CAUTION: The soleplate will still be hot, so
ensure the power cord and plug are kept away
from it and the sink.
7Press and hold the self-clean button (13) .
WARNING: Steam and boiling hot water will
drain from the holes in the soleplate. eep
hands and body away from the hot water. This
washes away the scale and minerals that have
built up inside the steam chamber.
8 Whilst still holding the self-clean button, gently
move the iron back and forth until the water tank
is empty.
9 When steam and hot water ceases to be
released from the soleplate, release the
self-clean button.
10 When the process is complete, re-connect to a
mains supply outlet and allow to heat up - this
will dry the soleplate.
11 Disconnect the iron from the mains supply outlet.
12 Rest your steam iron on its heel (14) and allow to
fully cool down.
13 Wipe the soleplate with a cold, damp cloth.
After this cleaning operation, empty out any
remaining water.
IMPORTANT: Do not attempt to descale the
soleplate with descaling products.
Maintaining your iron
23
RN305003 MUK Rev1.qxp_IB 13/03/2019 11:46 Page 10