Morrell SW-UNM-16FE1GC User manual
SW-UNM-16FE1GC
16-Port 10/100Mbps + 1-Port Gigabit Combo
Unmanaged Ethernet Switch
User Manual
Version 1.0 | 4/25/2015
1
Table of Contents
Chapter 1 Product Introduction ................................................................................................ 2
1.1 Product Overview ............................................................................................................ 2
1.2 Features ............................................................................................................................ 2
1.3 Package Contents ........................................................................................................... 2
Chapter 2 External Component Description ......................................................................... 4
2.1 Front Panel ....................................................................................................................... 4
2.2 Rear Panel ........................................................................................................................ 5
Chapter 3 Installing and Connecting the Switch ................................................................. 6
3.1 Installation ......................................................................................................................... 6
3.1.1 Desktop Installation .............................................................................................. 6
3.1.2 Rack-mountable Installation in 19-inch Cabinet .............................................. 6
3.1.3 Power on the Switch ............................................................................................ 7
3.2 Connect Computer (NIC) to the Switch ........................................................................ 7
Appendix: Technical Specifications ........................................................................................ 8
2
Chapter 1 Product Introduction
Congratulations on your purchasing of the Switch. Before you install and use this product,
please read this manual carefully for full exploiting the functions of this product.
1.1 Product Overview
This is a 16-Port 10/100Mbps + 1-Port Gigabit Combo Ethernet Switch, provides sixteen
10/100Mbps self-adaption RJ45 ports, plus one alternative gigabit port --- one
10/100/1000Mbps RJ45 port and one 100/1000Mbps SFP optical port, it can be used to
link bandwidth higher upstream equipment. Using store-and-forward technology,
combined with dynamic memory allocation, ensure the bandwidth effective allocation to
each port. Special design a flow control switch, flow control switch is “ON”, it can avoid
packet loss effectively when nodes in the sending and receiving data. Built-in high
reliability, design for wide voltage input application power supply, even if the voltage is not
stable of power grid, also can guarantee the equipment can work normally.
This Switch overall excellent performance, simple to use, plug and play, particularly
suitable for security application, and other application of the work condition is relatively
poor.
1.2 Features
Comply with IEEE 802.3, IEEE 802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.3az
standards.
Supports IEEE802.3x flow control for Full-duplex Mode and backpressure for
Half-duplex Mode.
Data exchange using storage-forward mode.
Flow control function can be controlled via a button.
Sixteen 10/100Mbps self-adaption RJ45 ports, plus one alternative gigabit port ---
one 10/100/1000Mbps RJ45 port and one 100/1000Mbps SFP optical port, it can be
used to link bandwidth higher upstream equipment.
Support MAC address learning.
LED indicators for monitoring power, link/activity.
Design a flow control switch, it can be manually control the flow control function for all
ports.
Built-in high reliability, design for wide voltage input application power supply.
19 inches full metal iron shell design, suitable for rack installation.
1.3 Package Contents
Before installing the Switch, make sure that the following the "packing list" listed OK. If
any part is lost and damaged, please contact your local agent immediately. In addition,
make sure that you have the tools install switches and cables by your hands.
3
One Ethernet Switch
One set of installation components
One AC power cord
One User Manual
4
Chapter 2 External Component Description
2.1 Front Panel
The front panel of the Switch consists of series of LED indicators, 16 10/100Mbps
RJ-45 ports, 1 10/100/1000Mbps RJ-45 port, 1 SFP port and a flow control switch
shown as below:
Flow control switch:
Designed to Open or close flow control function.
10/100Mbps RJ-45 ports (1~16):
Designed to connect to the device with a bandwidth of 10Mbps or 100Mbps. Each has a
corresponding Link/Act LED.
10/100/1000Mbps RJ-45 port (17T):
Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps.
Has a corresponding Link/Act LED.
SFP port (17S):
Designed to install the SFP module. The Switch features one SFP transceiver slot that are
shared with one associated RJ45 port(17T). A SFP port and an associated RJ45 port are
referred to as “Combo” port, which means they cannot be used simultaneously, and only
SFP port work or only RJ45 port work at the same time.
LED indicators:
The LED Indicators will allow you to monitor, diagnose and troubleshoot any potential
problem with the Switch, connection or attached devices.
5
The following chart shows the LED indicators of the Switch along with explanation of each
indicator.
LED STATUS STATUS DESCRIPTION
Power On Power On
Off Power Off
Link/Act
1~16
17T/S
On A device is connected to the port
Flashing Sending or receiving data
Off A device is disconnected to the port
2.2 Rear Panel
The rear panel of the Switch contains AC power connector and Grounding Terminal
shown as below.
AC Power Connector:
Power is supplied through an external AC power adapter. It s
upports AC 100~240V,
50/60Hz.
Grounding Terminal:
Located on the left side of the power supply connector, use wire grounded to prevent
electric shock.
6
Chapter 3 Installing and Connecting the Switch
This part describes how to install your Switch and make connections to it. Please read the
following topics and perform the procedures in the order being presented.
3.1 Installation
Please follow the following instructions in avoid of incorrect installation causing device
damage and security threat.
Put the Switch on stable place or desktop in case of falling damage.
Make sure the Switch works in the proper AC input range and matches the voltage
labeled on the Switch.
To keep the Switch free from lightning, do not open the Switch’s shell even in power
failure.
Make sure that there is proper heat dissipation from and adequate ventilation around
the Switch.
Make sure the cabinet to enough back up the weight of the Switch and its
accessories.
3.1.1 Desktop Installation
Sometimes users are not equipped with the 19-inch standard cabinet. So when installing
the Switch on a desktop, please attach these cushioning rubber feet provided on the
bottom at each corner of the Switch in case of the external vibration. Allow adequate
space for ventilation between the device and the objects around it.
3.1.2 Rack-mountable Installation in 19-inch Cabinet
The Switch can be mounted in an EIA standard-sized, 19-inch rack, which can be placed
in a wiring closet with other equipment. To install the Switch, please follow these steps:
a. attach the mounting brackets on the Switch’s side panels (one on each side) and
secure them with the screws provided.
7
b. use the screws provided with the equipment rack to mount the Switch on the rack and
tighten it.
3.1.3 Power on the Switch
The Switch is powered on by the AC 100~240V 50/60Hz internal high-performance power
supply. Please follow the next tips to connect:
AC Electrical Outlet: It is recommended to use single-phase three-wire receptacle with
neutral outlet or multifunctional computer professional receptacle. Please make sure to
connect the metal ground connector to the grounding source on the outlet.
AC Power Cord Connection: Connect the AC power connector in the back panel of the
Switch to external receptacle with the included power cord, and check the power indicator
is ON or not. When it is ON, it indicates the power connection is OK.
3.2 Connect Computer (NIC) to the Switch
Please insert the NIC into the computer, after installing network card driver, please
connect one end of the twisted pair to RJ-45 jack of your computer, the other end will be
connected to any RJ-45 port of the Switch, the distance between Switch and computer is
around 100 meters. Once the connection is OK and the devices are power on normally,
the Link/Act status indicator lights corresponding ports of the Switch.
8
Appendix: Technical Specifications
SPEC
Standards IEEE 802.3, IEEE 802.3u, IEEE802.3ab, IEEE 802.3x,
IEEE802.3az
Network Media
(Cable)
10BASE-T: UTP category 3,5 cable (maximum 100m)
100BASE-TX: UTP category 3,5 cable (maximum 100m)
1000Base-T: UTP category 5e cable (maximum 100m)
Number of Ports
16 x 10/100Mbps Auto-Negotiation ports
1 x 10/100/1000Mbps Auto-Negotiation port
1 x 1000Mbps SFP port
MAC address table 8K
Backplane bandwidth 5.2Gbps
Frame Filtering and
Forward Rate
10Mbps: 14880pps
100Mbps: 148800pps
1000Mbps: 1488000pps
Environment
Operating Temperature: 0℃~40℃
Storage Temperature: -10℃~70℃
Operating Humidity: 10%~90% non-condensing
Storage Humidity: 5%~90% non-condensing
Power supply
(internal) AC100~240V,50~60Hz,0.5A(max)
Table of contents
