Morris AFI-35250 User manual

Instruction ManualInstruction Manual
AFI-35250
DishwasherDishwasher
14 placesettings

Witheachwashcycle.
Compartment
For programmes with pre-wash only.
(Follow the user instructions!)
Electric indicator on control panel (if provided).
Check the rinse aid level
(On models with water softener system only.)
Electric indicator on control panel (if provided).
If there is no salt warning light in the control panel
(for some models), you can estimate when to fill the salt into
the softener by the number of cycles the dishwasher has run.
Check the regeneration
salt level
Load the baskets
Select a programme
Turnonthewatertap,closethedoor.Themachinewillstartworkingafterabout10seconds.
Running the dishwasher
Switch off the appliance
Turn off the water tap,
unload the baskets
Fill the detergent dispenser
Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more susceptible to break.
They will alsodry better.Unload the appliance, startingfrom the lower basket.
Changing theprogramme
Add forgotten dishes in the
dishwasher.
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions.
Press the Programme Button until the selected programme lights up.
( See the section entitled Operationg instruction )“”
When the working cycle has finished, the buzzer of the
dishwasher will sound 8 times, then stop.
Turn off the appliance using the On/Off Button.
If the appliance is switched
off during a wash cycle.
Open the door carefully.
Hotsteam may escape
when thedoorisopened!
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state ).
Switch on the appliance Open the door,press the On/Off button to switch on the appliance .
1.Open the door a little to stop the dishwasher.
2.After the spray arms stop working, you can open the door completely.
3.Add the forgotten dishes.
4.Close the door, the dishwasher will start running again after 10 seconds.
For detailed operating method read the corresponding content on the instruction manual.
1.A running cycle can onlybe modified if it hasbeen running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. Press the for more than3 seconds tocancel the running programme.
3. Select a new programme.
4. Restart the dishwasher.
Programme Button

To review the section on troubleshootingTips
will help youto solve some common problems
by yourself .
Dear Customer,
Please carefully readthismanualbefore usingthe
dishwasher,it will help you touseand maintainthe
dishwasher properly.
Pass it on to anysubsequentowner of the appliance.
Thismanualcontains sections on safety Instructions,
Operating Instructions, InstallationInstructions and
Troubleshooting Tips, etc.
The manufacturer, following a policy of constant
developmentandupdating of the product, may
make modificationswithout giving prior notice.
Keep it as a refer in the later days.
If you can not solvethe problems byyourself ,
please ask for the help of professional technicians.
This appliance is intended to be used in household
andsimilarapplications suchas:
-staff kitchen areas in shops,offices and other
working environments;
-farm houses;
-byclients inhotels,motels and otherresidential
type environments;
-bed andbreakfast type environments.
DishwasherFeatures.......................................3
A WaterSoftener...........................................4、
Attention before or after loading the Dishwasher
Baskets..........................................................9
Filtering System.............................................13
Caring for the Dishwasher..................... .........14.
B Loading the Salt into the Softener.................5、
C Fill the Rinse Aid Dispenser.........................5、
D Function of Detergent .................................6 、
Loadingthe upper ...............................10Basket
Loading the Lower ...............................10Basket
WashCycleTable...........................................11
Turning on theAppliance................................11
Change the Programme.............. ................12....
At the endof theWash Cycle...........................12
Before calling for service........................... .....22.
Errorcodes.................................... ..............23.
Technical information.............................. .....24..
ControlPanel...................................................3
.................................. 15Installationpreparation ...16Aesthetic panel's dimensions and installation
..............18Tensionadjustment of the door spring
.............................. 18Connectionof drain hoses ......................... 19Dishwasher installation steps
About Electricity Connecting...........................20
ColdWaterConnection.................................. 21
Hot ............. 21Water Connection.....................

This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce
the risk of anelectric shock by providing a path of
least resistance of electric current. This appliance
is equipped with a cord having an equipment-
grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with
all local codes and ordinances.
Keep children away from detergent and rinse aid, keep
child away from the open door of the dishwasher,
there could still be some detergent left inside.
ren
Donotabuse,siton,orstandonthedoorordish
rack of the dishwasher.
Do not touch the heating element during or
immediately after use.
(This instruction is only applicable to machines
with a visual heating element.)
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic items
not so marked, check the manufacturer's
recommendations.
Use only detergent and rinse additives
designed for an automatic dishwasher.
Never use soap, laundry detergent, or hand
washing detergent in your dishwasher. Keep
these products out of the reach of children.
During installation, the power supply must not
be excessively or dangerously bent or flattened.
Do not tamper with controls.
Do not place any heavy objects the
door when it is open. The appliance could tip
forward.
on or stand on
When loading items to be washed:
1) Locate sharp items so that they are not likely
to damage the door seal;
2 Warning: Knives and other utensils with
sharp points must be loadedin the basket
with their pointsdown orplaced in a
horizontalposition.
)
When usingyour dishwasher, youshould
prevent plastic items from coming into contact
with the heating element.(This instruction is only
applicable to machines witha visualheating
element.)
Ifthesupplycord is damaged, itmustbereplaced
bythemanufactureroritsserviceagentora
similarly qualified person in order to avoid a
hazard.
Please dispose of packing materials properly.
Use the dishwasher only for its intended function.
Remove the door to the washing compartment when
removing an old dishwasher from service or discarding it.
Dishwasher detergents are strongly alkaline, they
can be extremelydangerous if swallowed.Avoid
contact with skin and eyes and keep children away
from the dishwasher when the door is open.
Check that the detergent comparment isempty
after completion of thewashcycle.
The appliance is to be connected to the water
mains using new hose sets and that old hose-sets
should not be reused.
The maximum number of place settings to be
washed is14.
The maximum permissible inlet water pressure is
1Mpa.
The minimum permissible inlet water pressure is
0.04Mpa.
Children should be supervised to ensure that they do
not play with the appliance.
This appliance is not intended for use by persons
(including children with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
)
When using your dishwasher, follow the precautions listed below:
The door should not be left open,
since this could increasethe riskof tripping.
Improper connection of the equipment-grounding
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance; If it does not fit
the outlet. Have a proper outlet installed by a
qualified electrician.
Do not operate your dishwasher unless all
enclosure panels are properly in place. Open
the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.

Dispose of the dishwasher packaging material correctly.
All packaging materialscan be recycled.
Plastic parts aremarked with thestandard international abbreviations:
PE for polyethylene,e.g. sheet wrapping material
PS for polystyrene,e.g. padding material
POM polyoxymethylene, e.g. plastic clips
PP polypropylene, e.g. Salt filler
ABS Acrylonitrile Butadiene Styrene, e.g. Control Panel .
Packaging material couldbedangerous for children!
Fordisposing ofpackage and theappliance please goto arecycling centre. Therefore cut
off the powersupplycable and makethe doorclosing device unusable.
Cardboard packaging is manufactured from recycled paperand shouldbe disposedin the
waste paper collection for recycling.
By ensuring this productis disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused
by inappropriatewaste handling of thisproduct.
Formore detailed informationabout recycling of this product, please contact your local
city office and your household wastedisposal service.
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.






beforeusing it for the first time.
To get the best performance from yourdishwasher, read all operating instructions
5.On/OffButton:To turnon/off thepowersupply.
3.DelayButton : To Pressthe button to delay.You can
delaythe start of washing from 1 to 24 hours
1.Display Window: Program ,fill rinse aid,fill salt,
, remaining time, delay time, faut codes
and etc
Dual
zone wash
4. ProgramButton: To Pressthebutton toselecta
wash Program.
2. Alt Button: Dual zone wash function, press the button
to select either upper basket or lower basket loaded, and
the responseindicator willblinking
11 12
Back View
1
2
3
4
5
7
8
910
Front view
Lower basket
Saltcontainer
Dispenser
Cup shelf
Spray arms
Filter assembly
Inlet pipe connector
Drainpipe
Upper basket
Cutlery rack
Top spray arm
1
Inner pipe
5
6
7
8
9
10
12
11
3
24
6
13
Adjuster
13

The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from thewater, which wouldhave
a detrimentalor adverse effect on the operation ofthe appliance.
The higher the content of these minerals and salts,the harder your water is.
The softener should be adjusted accordingto the hardness of the water in your area. Your local WaterAuthority
can adviseyou onthehardnessofthewaterinyourarea.
Adjusting Salt Consumption
The dishwasher isdesigned to allow foradjustment in the amount of saltconsumed based onthe hardness of
thewaterused.Thisisintendedtooptimise and customise the levelo f salt consumption.
1. Open the door ,Switch on the appliance;
2. Press the Program button for more than 5seconds to start the water softener
set model within 60seconds after the appliance was switched on(The Saltand
Rinse aidwarning lights willbe onperiodicallywhen itgetinthe setmodel);
3. Press the Program button to select the proper set according toyour local environment,
the sets will change in the following sequence: H1->H2->H3->H4->H5->H6;
4. Press the Powerbutton to end thesetup model.
WATER SOFTENER
Thehardness ofthe watervariesfromplace to place. If hard water is used inthe dishwasher, deposits will
form on thedishes and utensils.
Theapplianceis equipped with a special softener thatuses a salt container specifically designed to eliminate
lime and minerals from the water.
Contact your local water board for information on the hardness of your water supply.
Please followthesteps belowforadjustment insaltconsumption.
If your model does not have any water softener, you mayskip this section.
Clark:Britishdegree
fH: French degree
DH: German degree
dH=1.25Clarke=1.78fH=0.178mmol/l
1
The manufactory setting: H4 (EN 50242)
Before using your dishwasher for the first time:
A. Set the water softener
B. Add 1.5Kgdishwasher salt and then full fill the salt container with water
C. Filltherinseaiddispenser
D. Fill in detergent
dH mmol/l
0~90~5 0~0.94 H1 0
10-20
6-11 1.0-2.0 H2 9
21-30
12-17 2.1-3.0
H3
12
H4 20
fH
0~6
7-14
15-21
Clarke
WATER HARDNESS
SelectorPosition Salt consumption
(gram/cycle)
18-22 31-40 22-28 3.1-4.0
41-60
23-34 4.1-6.0 H5 30
H6 60
29-42
35-55 61-98 43-69 6.1-9.8

1. The salt container must only be refilled when the salt warning light in the control panel comes on.
Depending on how well thesalt dissolves, the salt warning light may still be on even though the
salt container is filled.
If there is no salt warning light in the control panel (for some Models),you can estimate when to fill
the salt into the softener by the cycles that the dishwasher has run.
2. If there are spills ofthe salt, a soak or a rapid program should be runto remove the excessive salt.
Always use the salt intended for use with dishwasher.
The salt container is located beneath the lower basket and should be filledas explained
inthe following:
Attention!
Only use salt specifically designed forthe use indishwashers! Every other type of
salt not specifically designed for theuse in a dishwasher, especially table salt, will
damage thewater softener. In case of damages caused by the use of unsuitable
salt the manufacturerdoes not give any warranty nor is liable for any damagescaused.
Only fill withsaltjustbefore startingone of thecomplete washingprograms.
This will prevent any grains of salt or salty water, which may have been spilled,
remaining on the bottom ofthe machine for any periodof time, which maycause
corrosion.
The rinse aid isreleased during the final rinseto prevent water from forming droplets onyour dishes, which can
leave spots and streaks. It also improvesdryingby allowing water toroll offthe dishes. Your dishwasheris
designed to use liquidrinseaids.The rinseaiddispenser islocated inside thedoor next to the detergentdispenser.
To fill the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completely
black. The volume ofthe rinseaidcontainer is about 110ml.
RinseAid Dispenser
Function of RinseAid
Rinse aid is automatically added duringthe last rinse, ensuring thorough rinsing, and spotandstreak free drying.
Attention!
Only usebranded rinse aid for dishwasher. Neverfill the rinse aid dispenserwithanyothersubstances
(e.g. Dishwasher cleaning agent, liquid detergent).This would damage the appliance.
3.If the machine needs to be dumped for the reasonsof transit, repairand so on, please usethe bibulous cloth or
analog toblotup thewaterin the salt container,and screw thecaptightly,afterward, transitor repairthemachine.
Aftertransiting or repairing themachineandconfirming it in order, load the salt into the softeneraccordingto the
processof B. Loading the salt intotheSoftener .Otherwise, itcould bemake the big damage to the machine,for
example, rustiness,conk and so on. Such problems areout of theguarantee range.
“”
Full fill the salt container with water,It is normal for a small amount of water to come out of the
salt container.
AAfter the lower basket has been removed, unscrew and remove the cap fromthe salt container.
BPlace the end ofthefunnel (supplied) intothe hole and introduce about 1.5kg of dishwasher salt.
C
DAfter filling the container , screw the cap tightly back clockwise.
EThe saltwarning light will stopbeing after thesaltcontainer has beenfilled withsalt.
FImmediately after filling the salt into the salt container, a washing program should be started
program Otherwise thefilter system, pumpor other important parts ofthe machinemaybe damaged
bysalty water.This isoutof warranty.
(Wesuggest to use a short
).

To open the dispenser,turn the cap to the "open" (left) arrow and lift it out.
Pourthe rinse aid into the dispenser,being careful not to overfill.
Replace the cap by inserting italigned with "open" arrow and turning it tothe closed (right) arrow.
Adjusting RinseAid Dispenser
The rinse aid dispenser hassix orfour settings.Always start with thedispenser
set on"4". If spots and poor dryingare a problem, increase the amount of rinse
aid dispensedby removing thedispenserlid and rotatingthe dial to "5". If the
dishes still are notdrying properly orare show spots, adjustthe dial to the next
higher lever until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)
Increase the dose if there are drops of wateror limespots onthedishes after washing.
Reduce it ifthere aresticky whitishstains on your dishesora bluish film on glassware or
knife blades.
1
2
3
As the rinse aid diminishes, the size of the black dot
onthe rinse aidlevel indicator changes, as illustratedbelow.
Full
3/4full
1/2full
1/ 4full- Should refilltoeliminate spotting
Empty
When to Refill the RinseAid Dispenser
Ifthereis no rinse-aid warning lightin thecontrolpanel, you can estimatethe amount from the colour
of the optical level indicator C located next to the cap. When the rinse-aidcontainer is full, the whole
indicator will be dark .As the rinse-aid diminishes, thesize of the dark dot decreases. You should never let
the rinse aid level fall 1 / 4 full.
during the nextwash. Don'tforgetto replacethe cap before you closedishwasherdoor.
Clean up any rinse aid spilled while during filling with an absorbent cloth to avoid excessive foaming
Detergents with its chemical ingredients arenecessary to remove dirt,crushdirt and transport it outof the dishwasher.
Mostof the commercialqualitydetergentsare suitableforthispurpose.
""
Proper Use ofDetergent
Useonly detergent specificallymade for the use in dishwashers. Keep your detergent fresh and dry.
Don't putpowdered detergentinto the dispenser until you're ready to wash dishes.
Attention!

Amount ofDetergentto Use
Dishwasher detergent iscorrosive! Take care to keep it out of reach of children.
Based ontheir chemical composition, detergentscan be split in two basic types:
Detergenttabletsofdifferent brandsdissolve at differentspeeds. For thisreasonsome
detergenttablets cannot dissolve and develop theirfull cleaning power during short
programs. Therefore please use long programswhenusing detergent tablets, to
ensure the complete removal of detergent residuals.
The dispenser must be refilled before the start ofeach washcycle following the instructions
provided in the wash cycle table . Your dishwasher uses less detergent and rinseaid than
Conventional dishwasher. Generally, only one tablespoon of detergent is neededfor
anormal washload. Moreheavily soileditemsneedmore detergent.Alwaysaddthe
detergentjust before starting the dishwasher, otherwiseit couldget damp and will not
dissolve properly.
Concentrated Detergent
DetergentTablets
DetergentDispenser
conventional, alkaline detergentswith causticcomponents
low alkaline concentrated detergents with natural enzymes
Normally new pulverised detergent is without phosphate. Thus the water softener function of
phosphate is not given. In this case we recommend to fill salt in the salt container even when
the hardness of water is only 6 dH. If detergents without phosphate are used in the case of hard water
often white spots appear on dishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Strongand coloured spots will not
be removed completely. In thiscase pleasechoosea program with a higher temperature.
°
Detergents
Thereare 3 sorts of detergents
1.With phosphate andwithchlorine
2.With phosphate andwithout chlorine
3.Without phosphate and without chlorine
Always add the detergent just before starting each wash cycle.
Only use branded detergentaidfordishwasher.
If the lid isclosed: press release button.The lid will spring open.

Fill the detergent dispenserwith detergent.
The marking indicates the dosing levels , as
illustrated on the right:
Theplaceof main wash cycle detergent placed.
Theplaceof pre-wash cycle detergent placed.
Please observe the manufacturers dosing and storage
Recommendationsas statedonthedetergent packaging.
Closethe lid and press untilit locks in place.
If the dishes are heavily soiled, place an additional
detergent dosein the pre-wash detergent chamber.This detergent will take effectduring the pre-washphase.
A
B
Fill in Detergent
Youfind information about the amount ofdetergent for the single programme onthe last page.
Pleaseaware,thataccording tothe levelsoiling and the specific hardnessof water differencesarepossible.
Pleaseobserve themanufacturer's recommendationson the detergent packaging.
AB

Cutlery withwooden,horn china or
mother-of-pearl handles
Plasticitems that arenot heat resistant
Older cutlerywith glued parts thatarenot
temperatureresistant
Bonded cutlery items or dishes
Pewter or cooper items
Crystal glass
Steel items subject to rusting
Wooden platters
Items madefromsyntheticfibres
Some types of glasses canbecome
dull aftera large number of washes
Silver and aluminum parts have a
tendencyto discolourduring washing
Glazed patterns may fade if machine
washed frequently
Are not suitable Are oflimited suitability
Dishes and itemsof cutlery mustnot lie insideoneanother, orcover eachother.
To avoiddamage to glasses,theymust not touch.
Load large itemswhich are most difficult to cleanintothe lower basket.
The upper basket is designed to hold moredelicate and lighterdishware such as glasses, coffee
andteacups
Long bladed knives stored inan upright positionare a potential hazard!
Long and/or sharp itemsof cutlery such as carving knives must be positioned
horizontallyin the upperbasket.
Please do not overload your dishwasher. This is important forgood results and for
reasonable consumption of energy.
Load hollow items suchas cups, glasses, pans etc. With the opening facing downwardsso that
water cannot collect in the container or a deepbase.
Consider buyingutensilswhich are identifiedas dishwasher-proof.
Usea mild detergentthatisdescribedas'kind todishes'. If necessary, seek further
information from thedetergent manufacturers.
Forparticular items,select aprogramwithaslowa temperature aspossible.
To prevent damage, do not take glassand cutlery out of the dishwasher immediately
after the programmehas ended.
(For best performance of the dishwasher, follow these loading guidelines.
Features and appearance of baskets and cutlerybasketsmay vary from your model.)
Scrape off any largeamounts of leftover food. Soften remnants of burnt food in pans.
It is not necessary to rinse thedishes under running water.
Place objects inthe dishwasher in following way:
1.Items such ascups, glasses, pots/pans, etc. are faced downwards.
2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.
3.All utensils are stacked securely and can not tipover.
4.All utensils are placed in the way that the spray arms can rotate freely duringwashing.
Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
To prevent water dripping from the upper basket into the lower basket, we recommend thatyou
empty the lower basket first and then the upper basket.

Theupper basket is designed to hold more delicate
and lighter dishware such as glasses, coffee and
teacups and saucers, aswell asplates, small bowls
andshallowpans (as long asthey arenot toodirty).
Position thedishes andcookwareso thatthey will
notgetmovedbythespray ofwater.
We suggest that you place large items and the most
difficult to cleanitems are to be placedintothelower
basket: such aspots, pans, lids, serving dishes and
bowls, as shown in the figure below. It is preferable to
place serving dishes and lids on the side of the racks
in order to avoid blocking the rotation of the top spray
arm.
Pots,servingbowls,etc,mustalwaysbeplacedtopdown.
Deep pots should be slanted to allow water to flow out.
Please bereminded that:
The Bottom Basket features folding spikes so that larger or more pots and pans can be loaded.
Folding Spikes of Lower Basket
Forbetter stacking of pots and pans,
the spikescanbefolded down as
show in the picture right.
Folding back the cup shelives
For better stacking of pots and pans,
the spikes can befolded down as
show in the picture right.
Cutleryshouldbe placed inthecutlery rackseparately
from each other in the appropriate positions, and do
make sure the utensils do not nest together, this may
causebadperformance.
Adjusting the Upper Basket
The height ofthe upper basketcan be adjusted inorder to
create more space forlargeutensils both for the upper
/lowerbasket.Theheight of the upperbasket canbe
adjusted by lift upthe basket for the upperposition, and up
press the handle to lower the upper basket, see the picture
below:

*EN 50242 : Thisprogramme is the test cycle. The information for comparability test
in accordance with EN 50242,as follows:
Capacity: 14 setting
PositionUpper basket: upper wheels onrails
Rinse aid setting: 6
Pl:0.55w; Po:0.45w.
Starting a cycle wash
Draw out the lower and upper basket, load the dishes and push them back.
Itis commended to load the lower basket first, then the upperone(see the section entitled
Loadingthe Dishwasher ).
Pour in the detergent (seethe section entitled Salt, Detergent and RinseAid ).
Insertthe plug intothe socket. The power supplyis 220-240 VAC /50 HZ, the specification
of thesocket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.
Openthe door, press the ON/OFF Button.
Press the program Button , the wash program will be changed asfollows direction:
If a program is selected, the response light will light.Then close the door, the dishwasher
beginsto start.
“”
“”
Intensive->Normal->Eco->Glass->1Hour ;->Rapid
1
2
3
4
5
Means: need to fill rinse into the Rinse-Aid Dispenser.
()
Eco.
Intensive
Normal
(*EN 50242)
(or )3in1
5/30g
Rapid
Pre-wash(50 )
Pre-wash
Wash (65 )
Rinse
Rinse(55 )
Drying
℃
℃
℃
Pre-wash(45 )
Wash (50 )
Rinse
Rinse(60 )
Drying
℃
℃
℃
Pre-wash
Wash (50 )
Rinse(60 )
Drying
℃
℃
Wash (40 )
Rinse
Rinse(45 )
℃
℃
180
175
165
40
1.15
0.93
1.4
0.6
17
14
11
10
1Hour
Wash(60 )
Rinse (60 )
Drying
Pre-wash(50 )℃
℃
℃
60 10
1.15
20g
Glass
Pre-wash
wash(40 )
Rinse
Rinse(60 )
Drying
℃
℃
115 0.95 13.5
(or )3in1
5/30g
(or )3in1
5/30g
20g
(or )3in1
5/30g
For normally soiled loads,
such as , plates,glasses
andlightly soiledpans.
pots
For heaviest soiled crockery,
andnormally soiled pots
pans dishesetcwithdried
onsoiling.
、
、
Standard daily cycle for
normally soiled loads, such
aspots plates glasses.、、
For lightly soiled loads that
do not need excellent drying
efficiency.
Ashorterwashforlightly
soiled loads and quick wash.
For lightly soiled crockery
andglass

When the working cycle has finished, the buzzer of the dishwasher will soundfor8 seconds, then stop.Turn off
the appliance using theON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait for afew minutes before unloading thedishwashertoavoid handlingthedishes and utensilswhile they
are still hot and more susceptible to breakage. Theywill also dry better.
Switch Off the Dishwasher
The program light is on but is not blinking, only in this case the programmehasended.
1.Switch off the dishwasher bypressingthe ON/OFF button.
2.Turnoffthewatertap!
Open thedoor carefully.
Hot dishes are sensitive to knocks. The dishes should thereforebeallowed to cool down around 15 minutes
before removing from the appliance.
Open thedishwasher's door, leave it ajar and wait a few minutes beforeremoving the dishes. In this way they
will be cooler andthe drying will be improved.
Unloadingthedishwasher
It is normal that the dishwasher is wet inside.
Empty thelower basket first and then the upperone. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
If you open the door , the machine will pause. The program lightwill
stop blinking and the buzzerwill mooing every minuteunless you close the door .After
you close the door ,the machine will keep on working after 10 seconds.
during a washcycle
Premise:
Acycle that is underway can only be modified if it has only been running for a short time. Otherwise, the
detergent may have alreadybeen released,and the appliancemay have already drained the wash water.
If this is the case, the detergent dispenser must be refilled (see the section entitled " Loading the
Detergent " ).
Openthe door ,press the Program button , themachine will be in standbystate,
then youcan change the program to the desired cycle setting (see the section entitled " Starting a
wash cycle. . ." ).
more than 3 seconds
1
2
Aforgotten dish can be added any time before the detergent cup opens.
Add forgotten dishes.
Close the door
After the spray arms stop working, you can open the door
completely.
2
3
Open the door a little .
14
5
The dishwasher will run after 10 seconds.
Wash the arms in soapy and warm water and use a soft brush to
cleanthejets. Replace them afterrinsing them thoroughly.
When following this procedure from step1 to step 3, the filter system will be removed;
when following it from Step 3 to Step 1, the filter system will be installed.
It is dangerous to open the door when washing, because the hot water may scald you.

The filter prevents larger remnantsof food or other objects from getting inside the pum.
Theresidues may block the filter, in this case they mustbe removed.
The filter system consists of a coarse filter,a flat (Main filter)
And a microfilter(Fine filter).
Food and soil particles trapped inthisfilterarepulverizedby a
special jet on the lower spray arm andwasheddown to drain.
Larger items, such as piecesof bonesor glass, that couldblock
the drainaretrappedin the coarse filter. To removetheitems
caught by the filter,gently squeeze the tap on thetop of this
filterandliftout.
Thisfilter holds soil and food residues inthe sumpareaand
preventsitfrom being redeposit on the dishes during wash cycle.
Main filter
1
Coarse filter
2
Fine filter
3
2
3
1
Filter assembly
Thefilter efficiently
For best performance and results, the filter must be cleaned regularly. this reason, it isa goodidea to
remove thelarger foodparticlestrappedin the filter aftereach wash cycle by rinsing the semicircular filterand
cup under running water. To remove the filter device, pull thecup handle in the upwarddirection.
removes food particles from the wash water,allowing it to be recycledduring the cycle.
For
The dishwasher must never beused without the filters.
Improper replacementof the filter may reduce the performancelevel of the appliance
and damage dishesand utensils.
1
2
Step 1 Turn the filter in anti-clockwise direction,：
Step 2 lift the filter assy up：
When following this procedure from step1 to step 2, the filter system will be removed;
when following it from Step 2 to Step 1, the filter system will be installed.

The control panelcan be cleaned by using a lightly dampened cloth.
After cleaning, make sure to dry it thoroughly.
For the exterior, use agood appliance polish wax.
Neveruse sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
ProtectAgainst Freezing
1.Cutoff the electrical power to the dishwasher.
2.Turn off the water supply and disconnect the water inlet pipe from the water valve.
3.Drain the water from the inlet pipe and water valve. (Use a pan to gather the water)
4.Reconnect the water inlet pipe to the water valve.
5.Remove the filter at the bottomof the tub and use a spongeto soak up water in the sump.
please take frost protection measures onthe dishwasher in winter. Every fter washingcycles,
please operate as follows time a
：
Cleaning the Filter
CleaningThe Door
To clean the coarsefilter and the fine filter, use a cleaningbrush.Reassemble thefilter parts as shown in the figures
on thelast page and reinsert the entire assembly in the dishwasher, positioning itin itsseat and pressing downwards.
When cleaning the filters, don't knock on them. Otherwise, thefilters could be
contorted andtheperformance ofthe dishwashercouldbe decreased.
To clean theedge around the door,you should use only a soft warm, dampcloth.
To avoid penetrationof waterinto the door lock and electrical components,do not
use a spray cleaner of any kind.
Never use a spray cleaner to clean the door panel as it may damage the door lock
and electricalcomponents.
Abrasive agentsor some paper towels should not be used because of therisk of
scratching or leaving spots on the stainless steel surface.
Cleaning the SprayArms
If your dishwasher cannot work because of the ice,
please contact professional service persons.
It is necessary to clean the spray arms regularly for hard
water chemicalswillclogthesprayarmjetsandbearings.
- Inspect the filters for blocking after every timethe dishwasher has been used.
- By unscrewing the coarse filter, you can remove the filter system. Removeany foodremnants and
cleanthefilters underrunningwater.
Remarks:
The entire filter assembly shouldbe cleanedonce a week.
To remove thelower spray arm,pullout the spray armupward.
To remove the upper spray arm, hold the nut, rotate the arm
clockwisetoremoveit.
Wash the arms in soapyandwarm water and use a soft brushto
clean thejets. Replace them after rinsingthem thoroughly.

Itis recommend thatyourun awashcycle with the
dishwasher empty andthenremove the plug from the
socket, turn off the water supply and leave the door of
the appliance slightly open. This will help the door
sealsto lastlongerandpreventodoursfromforming
withintheappliance.
If the appliance must be moved, try to keep it in the
verticalposition. Ifabsolutelynecessary, itcanbe
positioned on its back.
Oneofthefactorsthatcauseodourstoforminthe
dishwasher is food that remains trappedin the seals.
Periodic cleaning with adamp sponge will preventthis
from occurring.
Before cleaning orperforming maintenance, always
remove the plug from the socket.
Tocleantheexteriorandrubberparts ofthedishwasher,
donot use solventsor abrasivecleaningproducts.
Only use aclothwith warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened withwater ana little
vinegar, or a cleaning product madespecificallyfor
dishwashers.
Remove the Plug
No Solvents orAbrasive Cleaning Moving theAppliance
Seals
After every wash, turn off the water supply to the
appliance and leavethe door slightlyopen sothat
moisture and odours arenot trapped inside.
After EveryWash
When not in Use for aLongTime
The installation of the pipes
and electrical equipments
should be done by professionals.
Electrical Shock Hazard
Disconnect electrical power before
installing dishwasher.
Failuretodosocanresultindeathor
electrical shock.
The installation position of dishwasher should be near the existing inlet and drain hoses and
power cord.
One side of the cabinet sink should be chosen to facilitate the connection ofdrainhosesof
the dishwasher.
Installation preparation
Note: please check the accompanying installation accessories(hook for aesthetic panel
,screw)
●

Please carefully read the installation instruction.
●Illustrations of cabinet dimensions and installation position of the dishwasher
Preparations should be made before moving the dishwasher to the installation place.
Choose a place near the sink to facilitate the installation of inlet and drain hoses
(see figure 1).
If dishwasher is installed at the corner of the cabinet, there should be somespace
(illustrated in figure 2) when the door is opened.
2
1
16
Minimum space when
the door is opened
【Figure2】
Cabinet dimensions
【Figure1】
Cabinet
Dishwasher
Door of
dishwasher
Minimum space of 50mm
1 The aesthetic wooden panel could be processed according to the Figure 3.
The aesthetic panel should
be processed in accordance
with the illustrated dimensions
【Figure3】
●Aesthetic panel's dimensions and installation
Less than 5mm
between the top
of dishwasher and
cabinet and the
outer door aligned
to cabinet.
90 °
90 °
600 mm
820mm
100
580mm
80
Space between cabinet
bottom and floor
Electrical, drain and
water supply line
entrances
(Unit: mm)

Installation of aesthetic panel
【Figure4a】
2 Install the hook on the aesthetic wooden panel and put the hook into the slot of the outer door of
dishwasher(see figure 4a). After positioning of the panel , fix the panel onto the outer door by
screws and bolts(See figure 4b) .
Installation of aesthetic
wooden panel
【Figure4b】
.takeawaythefour
short screws
. pin up the four long
screws
1
2
17