Morris TTB-178 User manual

TTB-178

Toreviewthe sectiononTroubleshootingTips
will help you to solve some common problems
by yourself .
The manufacturer, following a policy of constant
development andupdating of the product, may
make modifications without giving prior notice.
Dishwasher Features.................................... ...3
AttentionbeforeorafterloadingtheDishwasher
Baskets..........................................................9
FilteringSystem.............................................14
Caring for the Dishwasher..................... .........15.
A Loading the Salt into the Softener.................4、
C Fill theRinseAid Dispenser.........................5、
D Function ofDetergent .................................6 、
Loading the Basket...........................................9
Cutlery Basket...............................................10
WashCycleTable...........................................12
Turning on theAppliance................................12
Change the Programme.............. ................13....
At the End of the Wash Cycle...........................13
PositioningtheAppliance................... ..........17..
Water Connection.................................. .......17.
About Power Connection........................ .......17.
Connection of Drain Hoses..................... .......18.
Startof dishwasher............................. .. ......19.. ..
Beforecallingfor service........................... .....20.
Errorcodes.................................... ..............21.
Technical information.............................. .....22..
Control Panel...................................................3
If you can not resolve the troubles by yourself ,
please ask for the help of professional technicians.
B Adjusting Salt Consumption、........................4
When load bigger Dinner Plates .................... 11
Dear Customer,
Please carefully reading it before usingthe dishwasher
will help you to use and maintain the dishwasher properly.
Pass it on to any subsequent owner of the appliance.
This manual contains sections of Safety Instructions,
Operating Instructions,Installation Instructions and
Troubleshooting Tips, etc.
Keep it to refer to at a later date.
This appliance isintended tobe used in household
andsimilarapplications suchas:
-staff kitchen areas in shops, offices and other
working environments;
-farm houses;
-by clients inhotels, motels and otherresidential
type environments;
-bed andbreakfast type environments.

1
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of
least resistance of electric current. This appliance
is equipped with a cord having an equipment-
grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with
all local codes and ordinances.
Keep children away from detergent and rinse aid, keep
child away from the open door of the dishwasher,
there could still be some detergent left inside.
ren
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic items
not so marked, check the manufacturer's
recommendations.
Use only detergent and rinse additives
designed for an automatic dishwasher.
Never use soap, laundry detergent, or hand
washing detergent in your dishwasher. Keep
these products out of the reach of children.
During installation,thepowersupplymustnot
be excessively ordangerouslybentorflattened.
Thedoorshouldnot be left intheopenposition
sincethiscould present atrippinghazards.
Do not tamper with controls.
Do not place any heavy objects of stand on the
door when it is open. The appliance could tip
forward.
When loading items to be washed:
1) Locatesharp items so that theyarenot likely
todamagethedoorseal;
2 Warning: Knives and other utensils with
sharp points must be loadedin the basket
with their pointsdown or placedin a
horizontalposition.
)
When using your dishwasher, you should
prevent plastic items from coming intocontact
withheatingelement.(Thisinstruction isonly
applicable to machines with a visual heating
element.)
If the supply cord is damaged, it must be replaced
by the manufacturer or itsserviceagent ora
similarly qualified person in order to avoid a
hazard.
Please dispose of packing materials properly.
Use the dishwasher only for its intended function.
Dishwasher detergents are strongly alkaline, they
can be extremelydangerous ifswallowed.Avoid
contact with skin and eyesandkeep children away
from the dishwasherwhen the door is open.
Check that the detergent receptible is empty
after completionof the wash cycle.
The applianceis to be connected to the water
mains using new hosesets and that oldhose-sets
should not be reused.
The maximumpermissible inlet water pressureis
1Mpa.
The minimum permissibleinlet water pressureis
0.04Mpa.
Children should be supervised to ensure that they do
not play with the appliance.
This appliance is not intended for use by persons
(including children with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
)
When using your dishwasher, follow the precautions listed below:
Do not operate your dishwasher unless all
enclosure panels are properly in place. Open
the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance; If it is not fit for
the outlet. Have a proper outlet installed by a
qualified electrician.
The maximumnumber of placesettingsto be
washed is 6.

2
Dispose of the dishwasher packaging material correctly.
All packaging materials can be recycled.
Plastic parts are marked with the standard international abbreviations:
PE for polyethylene, e.g. sheet wrapping material
PS for polystyrene,e.g.paddingmaterial
POM polyoxymethylene, e.g. plastic clips
PP polypropylene, e.g. Salt filler
ABS AcrylonitrileButadiene Styrene, e.g. Control Panel .
Packaging materialcouldbe dangerous for children!
For disposing ofpackage and theappliance please goto arecycling centre. Therefore cut
off the powersupplycable and make the doorclosing device unusable.
Cardboard packaging ismanufactured fromrecycledpaperand shouldbe disposedin the
waste paper collection for recycling.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused
by inappropriatewaste handlingof this product.
For moredetailed informationabout recycling of this product, please contact your local
city office and your household waste disposal service.
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.






3
beforeusingit forthe first time.
To get the best performance from yourdishwasher,read all operating instructions
Front view Back View
Filter assemblyDetergent Dispenser
Cup Shelf
Cutlery Basket RinseAid Dispenser
Inlet pipe connector
Drainpipeconnector
SprayArms Basket
1
Salt Container
5
67 89 10
3
2 4
3
26
4
7 8
910
5
1
5
2
3
4
6
Power Button: To turn on/off the power supply. Washing Program Selector: To press the button to
selectwash cycles.
Start/Pause Button: Press this button to start or
pause the dishwasher.
Display: Toshow delay time, salt warming,
rinse-aid warming, countdownof washing
cycle'stime, program whatyouselected, child
lock function and so on.
Child lock function: To press program function
buttonandStart/Pause buttonat the sametime.
Delay Button To press the button to delay time
(0~24hours) ：
123456

normal for a small amount of water to come out of the salt container.Itis
1. The salt container must only be refilled when the salt warning light in the control panel comes on.
Depending on how fully the salt dissolves, the salt warning light may still be on even though the
salt container is filled.
If there is no salt warning light in the control panel (For some Models),you can judge when to load
the salt into the softener by the cycles that the dishwasher had run.
2. If there are spills ofthe salt,a soak or a rapid program should be run to remove the excess salt.
Always use salt intended for use with dishwasher.
The salt container is located beneath the basket and should be filled as follows:
Attention!
Only use salt specifically designed for use in dishwashers!All other types of
salt not specifically designed for use in a dishwasher, especially tablesalt, will
damage the water softener. incase of damages caused by the use ofunsuitable
salt the manufacturer does not give any warranty nor is liable for any caused
damages.
Only fill withsalt justbefore starting one of thecomplete washingprogrammes.
This will prevent any grains of salt or salty water, which may have been split,
remaining of the bottom of the machine for any period of time, which may cause
corrosion.
4
ARemove the basket and then unscrew and remove the cap from the salt container.
BBefore first wash, add 1lt. of water inthe salt container of your machine.
CPlace the end of the funnel (supplied) into the hole and introduce about 1kg of salt.
DAfter filling the container , screw the cap tightly back clockwise.
EUsually, the salt warning light will be cease to be illuminated within2-6 daysafterthe salt container has been filledwith
salt.
FImmediately after filling the salt into the salt container, a washing programme should be started
Otherwisefiltersystem, pumpor other important parts ofthemachinemay be damaged bysalty
water.Itisoutof warranty.
If your model have water softener, youmay skip this section.no
Step 1: Enter the status of saltadjustment
B.Adjusting Salt Consumption
Within 60second after poweron,press Delay and Program button
for 5 seconds at the same time,then enter setting mode.
Digital display stalls"H *", the controller factory default H6

Therinse aid isreleasedduring the final rinse to prevent water from forming droplets onyour dishes.That can leave
spots and streaks. It also improvesdrying by allowing water to sheet offthe dishes.Your dishwasher isdesigned to
useliquid rinseaids. The rinse aiddispenser islocated inside thedoor next tothe detergent dispenser. To fill the
dispenser, open thecapand pour the rinse aidintothe dispenseruntil thelevel indicatorturns completely black.
The volume of the rinseaid container is about 110ml.
RinseAid Dispenser
Function of RinseAid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spotand streak free drying.
5
Step 2: select a certain level of salt consumption
Setting on the
water softener Digital display stalls
1
H1
2
3
4
5
6
1) German degree of measurement for thewater hardness
2) millimol, internationel unit for water hardness
*)factorysetting
dH
Water Hardness level
mmol/l
1) 2)
*
0-5 0-0.9
6-11 1.0-2.0
12-17
18-22
23-34
35-45
2.1-3.0
3.1-4.0
4.1-6.1
6.2-8.0
H2
H3
H4
H5
H6
1) When you push program button , digital display stalls of information.
Press stalls by "H1 H2 H3 H4 H5 H6 H1"cycle of change
2) In setting mode, press the Delay button,
or 60s there is no change in stalls (program key) operation, then exit the set mode,
the machine isinto standby status.
3)
program button every time,
Then youcan select a programto startyourmachine.
Power
Botton Delay
Botton Program
Botton
Digital display
Thereare 6 levels of salt consumption in all.
It is recommendedto select the level according to below table:

To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Pour the rinse aid into the dispenser, being careful not to overfill.
Replace the cap by inserting it aligned with "open" arrow and turning it tothe closed (right) arrow.
Adjusting RinseAid Dispenser
The rinse aid dispenser has six or four settings.Always start with the dispenser
set on "4". If spots and poor drying are problems, increase the amount of rinse
aid dispensed by removing the dispenser lid and rotating the dial to "5". If the
dishes still are notdrying properlyor are spotted, adjust the dial to the next
higher number until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)
Increase the dose if thereare drops of wateror limespotsonthe dishes afterwashing.
Reduce it ifthere are sticky whitish stains on your dishes or abluish film on glassware or
knife blades.
1
2
3
As the rinse aid diminishes, the size of the black dot
ontherinse aidlevel indicator changes, as illustrated below.
Full
3/4full
1/2full
1/ 4full- Should refill to eliminate spotting
Empty
6
When to Refill the RinseAid Dispenser
If thereis no rinse-aid warning light in the control panel, you can judge the amount of rinse-aid by the color
oftheoptical level indicator located nexttothecap. Whenthe rinse-aidcontainer isfull, the whole
indicator will be dark .As the rinse-aid diminishes, thesize of the dark dot decreases. You should never let
therinseaidgetbelow1/4full.
during the next wash. Don't forget to replace the cap before you close dishwasherdoor.
Clean up any rinse aid split during filling with an absorbent cloth to avoid excessive foaming
Detergents with its chemical ingredients are necessary to remove dirt,crush dirt and transport it outof the dishwasher.
Most of commercial quality detergents are suitable for this purpose.
Detergents
There are 3 sorts of detergents
1.Withphosphate and withchlorine
2.With phosphate and without chlorine
3.Without phosphate and without chloride
""
Attention!
Only usebranded rinse aid for dishwasher. Never fill therinse aid dispenser withanyothersubstances
(e.g. Dishwasher cleaning agent, liquid detergent).This would damage the appliance.

7
AmountofDetergenttoUse
Based ontheir chemicalcomposition, dishwasher can be split intwobasictypes:
Detergent tabletsofdifferent brandsdissolve at differentspeeds. For this reasonsome
detergenttablets cannot dissolve and develop theirfullcleaning power during short
programmes.Therefore pleaseuselong programmes whenusing detergenttablets,to
ensure the complete removal of detergent residuals.
The dispensermust be refilled before the start of each wash cycle following the instructions
provided in the Wash Cycle Table .Your dishwasher uses less detergent andrinse aidthen
conventionaldishwasher. Generally, only one tablespoon ofdetergent isneededfor
a normal wash load.Also, more heavily soiled items need more detergent.Alwaysadd the
detergent just before starting the dishwasher, otherwise it couldget damp and will not
dissolve properly.
Concentrated Detergent
DetergentTablets
DetergentDispenser
Always add the detergent just before starting each wash cycle.
Only use branded detergentaidfordishwasher.
If the lid is closed: press release button.The lid springs open.
conventional, alkaline detergents with caustic components
low alkaline concentrated detergents with natural enzymes
Normally new pulverised detergent is without phosphate.Thewatersoftenerfunctionof
phosphate is not given. In this case we recommend to fill salt in the salt container even when
the hardnessof wateris only 6 dH. If detergentswithout phosphate wereusedin case ofhardwater
often white spots appear at dishes and glasses. In this caseplease add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Strongand coloured spots will not
removed completely. In this case please choose a programme with higher Temperature.
°
Detergent tablet
Detergent powder

8
Fill the detergent dispenser with detergent.
The marking indicates the dosing levels , as
illustrated on right:
The place of main wash cycle detergent placed.
The place of pre-wash cycle detergent placed.
Please observe the manufacturers dosing and storage
Recommendations asstatedonthedetergent packaging.
Close the lid and press until it locks in place.
If the dishes are heavily soiled, place an additional
detergent dosein the pre-wash detergent chamber.This detergent will take effect during the pre-wash phase.
A
B
Fill in detergent
You find information about the amount of detergent for thesingle programme on the last page.
Please aware, that according tothe levelsoiling and the specific hardness of water differencesarepossible.
Pleaseobservethemanufacturer's recommendations onthe detergent packaging.
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not
Older cutlery with glued parts that is not
temperature resistant
Bonded cutleryitems or dishes
Pewteror cooper items
crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
heat resistant
Some types of glassescanbecome
dull after alargenumber of washes
Silverand aluminium partshavea
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently
Are not suitable Are of limited suitability
Usea milddetergent that isdescribed as'kind ofdishes'.If necessary, seek further
information from detergent manufacturers.
For particular items, select a programme with as low a temperature.
Toprevent damage, do not take glass andcutlery out of the dishwasher immediately
after the programmehas ended.
Consider buying utensils which are identified as dishwasher-proof.
Don't put powder detergentintothedispenser until you're ready to wash dishes.
Use only detergent specificallymade for use in dishwashers. Keep your detergent fresh and dry.
Proper Use of Detergent
Dishwasher detergent is corrosive! Take care to keepit out of reach of children.

Dishesand itemsof cutlery mustnot lie insideoneanother, orcover each other.
Toavoiddamage to glasses, theymust not touch.
Loadlargeitemswhicharemostdifficulttocleanintothebasket.
Long bladed knives stored in an upright position are a potential hazard!
Long and/or sharp items of cutlery such as carving knives must be positioned
horizontallyin the basket.
Please do not overload your dishwasher.
Load hollow items such as cups, glasses, pans etc. With the opening downwards sothat
water cannot collect in the container or a deep base.
(For best performance of the dishwasher, follow these loading guidelines.
Features and appearance of baskets and cutlery baskets may vary from your model.)
Scrape off any large amounts of leftover food. Soften remnants of burnt food in pans
It is not necessary to rinse the dishes under running water.
Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots/pans, etc. are face down.
2.Curved items, or those with recesses, should be loaded at a slant so that water can run off.
3.Allutensils are stackedsecurelyand can not tipover.
4.All utensils are placed in the way that the spray arms can rotated freely during washing.
Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
9
Position the dishes and cookware sothat they will not getmoved by the spray of water.
Saucers
4
Mediumservingbowl
3
Glasses
1
Cups
6
Oval platter
7
Dinner plates
8
Soup plates
Dessert dishes
9
Dish
5
Cutlery basket
10
2

10
Cutlery should be placed inthe cutlery basket with handles atthe bottom. If the rack has side baskets, the spoon
shouldbe loadedindividually into the appropriateslots, especially long utensils shouldbeplaced inthehorizontal
position at the front of the upperbasket as shown.
Do not let any item extend through bottom.
Always load sharp utensils with the sharp point down!
Teaspoons
4
Soup spoons
2
Forks
1
Serving forks
8
Serving spoons
6
Knives
5
3
Dessert spoons
7
Gravy ladles
Plate racksof Basket
The basket is fitted with plate racks which
can be stowed horizontal ifrequired.
616
2
1
1
1
2
5
55
1
2
5
5
1
4
3
3
3
3
4
4
4
7
3
5
4
48
3
2
22

11
Plate racksof Basket
When load bigger Dinner plates,
please fold the rack to left picture
showed location.
The maximum plate can be loaded
is 270mm(10 inches) diameter.
Position the dishes and cookware so that they will not get moved by the spray of water.
Saucers
4
Large serving bowl
3
Glasses
1
Cups
6
7
Dinner plates
8
Soup plates
Dessert dishes
9
Dish
5
Cutlery basket
2

12
Starting a washcycle...
Draw out the basket(seethe sectionentitled Loading theDishwasher ).
Pour in the detergent (see the section entitled Salt,
Detergentand RinseAid ).
Insert the plug into thesocket.The powersupply is 220-240
VAC 50 HZ,the specificationof the socket is 10 A250VAC.
Make sure that the water supply is turned on to full pressure.
“”
“
”
Press the program button, the wash program will be changed as follows direction
Then press the Start/Pause button, the dishwasher begins to start.
I->Rapidntensive->Normal->Eco->Glass->1 hour ;
When you press the Start/Pause button to pauseduringwashing,
the time light will stop blinking and the dishwasher will mooing
every minute unless youpressthe Start/Pause button to start.
*EN 50242 : This programme is the test cycle. The information for comparability test
in accordance with EN 50242, as follows:
Capacity: 6 setting
The power consumption of off-mode is 0.3W
left-on modeis0.4W
Rinse aid setting: 6
Pre-wash 50
Wash (70 )
Rinse
Rinse
Rinse(70 )
Drying
（℃）
℃
℃
For the heaviestsoiled loads,
such aspots,pans,casserole
dishes and dishes that have
been sitting with dried food
on themfor a while.
3/15 g.
145
0.94 11.0
Intensive
For normally soiled loads,
such as pots, plates,
glassesandlightly
soiled pans.
3/15 g. 125 0.70 8.4
Pre-wash
Wash (60 )
Rinse
Rinse(70 )
Drying
℃
℃
Normal
For lightly soiled loads that do
not need excellent drying
efficiency.
15g. 60 6.8
1hour
0.55
Standard daily cycle for
normally soiled loads,
such as pots, plates,
glasses.
170 0.61 7.0
Pre-wash
Wash (50 )
Rinse
Rinse(70 )
Drying
℃
℃
Wash (45 )
Rinse
Rinse(60 )
Drying
℃
℃
(EN 50242)
Eco
3/15 g.
For lightly soiled loads,
such as glasses, crystal and
finechina.
75 0.48 6.8
Glass
15g.
Ashorter wash for lightly
soiled loads that do not
need drying.
15g. 30 6.0
Rapid
0.30
Wash(40 )℃
Rinse
Rinse
Wash (65 )
Rinse
Rinse(50 )
Drying
℃
℃

It is dangerous to open the door when washing, because the hot water may scald you.
Whenthe working cycle has finished, the buzzerof dishwasher will sound 8 seconds,then stop.Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait a fewminutes before unloadingthe dishwasher to avoid handling the dishes and utensils while they
are still hot and more susceptible to breakage. They will also dry better.
Switch Off the Dishwasher
1.Switch off the dishwasher by pressingthe ON/OFF button.
2.Turnoffthewatertap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading thedishwasher
It is normal that the dishwasher is wet inside.
will keep on working after 10 seconds.
If you open the door when washing, the machine will pause. When you close the door , the machine
13
Aforgotten dish can be added any time before the detergent cup opens.
Add forgotten dishes.
Close the door
After the spray arms stop working,you can open the door
completely.
2
3
Open the door a little to stop the washing.
14
5
6
Premise:You can modify thewashingprogram,Whenthe dishwasher just
runs for a short time. Otherwise, the detergent may havealready been
released, and the appliance may have already drained the wash water. If this
is the case,the detergent dispenser must be refilled (seethe section entitled
" Loading the Detergent " ).
Press Start/Pause Button themachinepause,then pressProgramButton
more than three seconds themachine will be in stand by state ,then you can
change the program to the desired cycle setting (see the sectionentitled
" Starting a wash cycle. . ." ).
Press Program Button and Start/Pause Button at the same time,
If you want to cancel, Press Program Button and
Start/Pause Buttonat the same time in the same way.
NOTE: If you open the door during washing, themachinewill pause. When you
closethe door and press theStart/PauseButton, the machine will keep on
workingafter10 seconds.
Child lock
function go into effect.
Press the Start/Pause button
Press the Start/Pause button, the dishwasher will run
after 10 seconds.
The LED display shows the state of the dishwasher:
display
display
a) Colon icon in the LED is on butnot blinking------------------stand by or pause
b) Colon icon in the LED blinking----------------------------------Running

The filter prevent larger remnants of food or other objects from gettinginside the pump.
The filter system consists of a coarse filter, a flat (Main filter)
and a micro filter (fine filter).
Food andsoil particles trapped by this filter arepulverized by a
special jet on the spray arm and washed down to drain.
Mainfilter
1
Larger items, such aspieces of bone or glass,thatcould block
the drain are trapped in the coarse filter. To removethe items
caught bythe filter, gently squeeze thetap on the top of this
Coarse filter
3
This filter holds soil and food residue in the sump area and
prevents it from being redeposit on the dishes during wash cycle.
Fine filter
2
2
3
1
Filterassembly
Thefilter efficiently
For best performance and results, the filter assembly must be regularly. this reason, it is agood idea to
remove thelarger food particles trapping inthe filterafter each wash cyclebyrinsing the filter and cup under
running water. To remove the filter assembly, pull on the cuphandle in the upward direction.
removes food particles from the wash water,allowing it to be re-cyclated during the cycle.
For
Never run the dishwasher without the filters in place.
The dishwasher must never be used without the filters.
Improper replacementof the filter may reduce the performancelevel ofthe appliance
and damage dishesand utensils.
the filter system will be installed.
If do it from step1 to step 3, the filter system will be removed;while if do it from Step 3 to Step 1,
14
Step１：contrarotate the Fine ,
liftitup;Step2:
filter
Step3：lift the Main filter up
2
1
3
filterand lift out.

The control panel can be cleaned by usinga lightly dampened cloth and dry thoroughly.
The exterior use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners onany part of the dishwasher.
ProtectAgainst Freezing
1.Cut off electrical power to the dishwasher.
2.Turn off the water supply and disconnect the water inlet pipe from the water valve.
3.Drain water from the inlet pipe and water valve. (Use a pan to catch the water)
4.Reconnect the water inlet pipe to the water valve.
5.Removethe filter at the bottom of the tubanduse asponge touseup waterin sump.
please take frost protection measures ondishwasher in winter. E fter washing cycles,
please operate as follows ach time a
：
- Inspect the filters for blockingevery time the dishwasher has been used.
- By unscrewing the coarse filter.you can remove thefilter system.Remove any food remnantsand
cleanthefilters underrunningwater.
Remarks:
CleaningThe Filter
CleaningThe Door
To clean the coarse filter and the fine filter, use a cleaning brush. Reassemble the filter parts as shown in the figures
inthelast pageandreinsert the entire assemblyin the dishwasher, positioning in its seat and pressingdownward.
The entirefilter assembly shouldbe cleaned once a week.
Whencleaning the filters, don't knock on them. Otherwise, the filters could be
contorted andtheperformance ofdishwasher could bedebased.
To cleantheedgearoundthedoor, youshoulduseonly a softwarm,
damp cloth. To avoid penetration of water into the door lock and
electrical components, do not use a spray cleaner of any kind.
Never use a spray cleaner to clean the door panel as it may damage the door lock
and electricalcomponents.
Abrasive agent or some paper towel should not be used because of the risk of
scratching or leaving spots on the stainless steel surface.
15
If your dishwasher cannot work because of the ice, please contact professional service persons.

Itis recommendthatyourun a washcycle withthe
dishwasher empty and then remove the plug from the
socket, turn off the water supply and leave the door of
the appliance slightly open. This will help the door
sealstoast longerandpreventodours from forming
withinthe appliance.
If the appliance must be moved, try to keep it in the
verticalposition. Ifabsolutelynecessary, itcanbe
positioned on its back.
One of thefactors that cause odors to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with adamp sponge will prevent this
from occurring.
After every wash, turn off the water supply to the
appliance and leave the door slightlyopen sothat
moisture and odors are not trapped inside.
Before cleaning or performing maintenance, always
remove the plug from the socket.
Tocleantheexteriorandrubberpartsofthedishwasher,
donot use solventsor abrasivecleaningproducts.
Only use a cloth with warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened withwater with a little
vinegar, or a cleaning product madespecifically for
dishwashers.
After EveryWash
Remove the Plug
No Solvents orAbrasive Cleaning Moving theAppliance
Seals
When itis not in needfor a long time
16
The installation of the pipes
and electrical equipments
should be done by professionals.
Electrical Shock Hazard
Disconnect electrical power before
installingdishwasher.
Failureto do so can result indeath
or electrical shock.
The installation position ofdishwasher should be near the existing inlet anddrain
hosesandpowercord.
One side of the cabinet sink should be chosen to facilitatethe connection ofdrain
hosesof the dishwasher.
Cleaning the SprayArms
Thespray arms canbe easily removed for periodiccleaning
of the nozzles, to prevent possible clogging. Wash them
under running water and carefully replace them in their seats,
checking that their rotary movementis inno way impeded.
Graspthe middle ofthe spray arm, pull it upwardsto remove
it.Wash the arms undera jetof running waterandreturn them
carefully totheir seat. After reassembly, check that the spray
arms turn freely. Otherwise, check that they havebeen
installed correctly.

Ensure the voltage and frequency of the power being corresponds to
those on the rating plate. Only insert the plug into an electricalsocket which isearthed
properly. If the electrical socket to which the appliance must be connected is not
appropriate fortheplug , replace the socket, ratherthan usingaadaptors or thelike as
they couldcause overheatingandburns.
Pleaselook at therating label to know the ratingvoltage and connectthe dishwasher to the appropriate powersupply.
Use the required fuse 10 amp, timedelay fuse or circuit breakerrecommended and provide separate circuit serving
only this appliance.
This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of
electric shock by providing a path of least resistance for the electric current. This appliance is equipped with
a cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an
appropriate outlet that is installed and earthed in accordance with all local standards and requirements.
For personal safety:
DO NOT USEAN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDERANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
17
for personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE
FROM THE POWER CORD. EARTHING CONNECTION
Improper connection of the equipment earthing conductor can result in the risk of an
electric shock.
Check with a qualified electrician or service representative if you are in doubt whether the
appliance is properly earthed.
Do not modify the plug provided with the appliance. If the plug does not fit properly to the
outlet, please have a qualified electrician to install a proper outlet.
and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply
Position the appliance in the desired location. The back should rest against the wall behind it,
and drain hosesthatcanbepositioned totheright ortheleftto facilitate properinstallation.
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure
that it is fastened tightly in place. If the water pipes are new or have not been used for
an extended period of time, let the water run to make sure that the water is clear and
free ofimpurities. Ifthisprecaution isnottaken, thereis arisk that the water inletcan
get blocked and damage the appliance.
Please close the hydrant afterusing.

Insert the drain hose into a drain pipe with a minimum diameterof 4cm, or let it
runintothesink,makingsuretoavoidbendingorcrimpingit.Usethespe ial
plastic support that comeswith the appliance.The free endof the hosemust be
ata height lower than 75cm and must not beimmersed in water toavoid the back
flow of it.
c
18
The special plastic hose support must be solidlyfastened tothe wall to
prevent thedrainhose from moving and allowing waterto spill outside
the drain.