Morris TTW-165 User manual

TTW-165

For detailed operating method read the corresponding content on the instruction manual.
Switch on the appliance Press the Power switch button to switch on the appliance, Open the door.
Fill the detergent dispenser With each wash cycle.
Compartment
For programmes with pre-wash only.
(Followthe user instructions!)
A B C
Check the rinse aid level Electric indicator on control panel (if provided).
Check the regeneration
salt level
(On models with water softener system only.)
Electric indicator on control panel (if provided).
If there is no salt warning light in the control panel
(for some models), you can estimate when to fill the salt into
the softener by the number of cycles the dishwasher has run.
Load the baskets
Select a programme
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loadinginstructions.
Close the door，Press the programme button until the selected programme lights up.
( See the section entitled“Operation instruction”)
Running the dishwasher Turn on the water tap and press the Start/Pause button. The machine will start working
after about 10 seconds.
Changing the programme
Add forgotten dishes in the
1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water alreadydrained. If this is the case, the detergent
dispenser must be refilled.
2. Press the Start/Pause button ,then press the program button more than 3 seconds to cancel the
running programme. .
3. Select a new programme.
4. Restart the dishwasher.
dishwasher.
If the appliance is switched
off during a wash cycle.
1.Press the start/pause button to stop the machine.
2.Open the door.
3.Add the forgotten dishes.
4.Close the door, then press the start/pause button, the dishwasher will
start running again after 10 seconds.
If the appliance is switchedoff during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state ).
Open the door carefully.
Hot steam may escape
when the door is opened!
Switch off the appliance When the working cycle has finished, the buzzer of the
dishwasher will sound 8 times, then stop.
Turn off the appliance using the Power button.
Since the appliance is standing by, it will power off automaticly after 30 minutes without any operation.
Turn off the water tap,
unload the baskets Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more susceptible to break.
They will also dry better.Unload the appliance, startingfrom the lower basket.

Dear Customer,
Please carefully rea d this manual before using the
dishwasher, it will help you to use and maintain the
dishwasher properly.
Keep it to refer to it at a later date.
Pass it on to any subsequent owner of the appliance.
This manual contains sections on safety Instructions,
Operating Instructions, Installation Instructions and
Troubleshooting Tips, etc.
Control Panel ...........................................................3
Dishwasher Features ........................................3
A、Loading theSalt into the Softener ..................4
B、Fill the Rinse Aid Dispenser ..........................5
C、Function of Detergent...................................6
Attention before or after loading the Dishwasher
Baskets ............................................................9
Loading the Basket............................................9
Cutlery Basket.................................................10
To review the section on troubleshooting Tips
will help you to solve some common problems
by yourself .
If you can not solve the problems by yourself ,
please ask for the help of professional technicians.
Wash Cycle Table ................................................ 11
Turning on theAppliance................................ 11
Change the Programme........................................12
At the end oftheWash Cycle.............................12
Filtering System..............................................13
Caring for the Dishwasher................................14
The manufacturer, following a policy of constant
development and updating of the product, may
make modifications without giving prior notice.
This user manual shall also be got from the
manufacturer or responsible vendor.
Positioning the Appliance.................................. 16
About Power Connection .................................16
Water Connection........................................... 1 6
Connection of Drain Hoses...............................17
Start of dishwasher.......................................... 18
Before calling for service................................ 19
Error codes.....................................................2 0
Technical information ......................................21

When using your dishwasher,
follow the precautions listed below:
This appliance is intended to be used in household
and similar applications such as:
-staff kitchen areas in shops, offices and other
working environments;
-farm houses;
-by clients in hotels, motels and other residential type
environments;
-bed and breakfast type environments.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision.（For EN60335-1）
This appliance is not intended for use by persons
(including children )with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.（For IEC60335-1 ）
This appliance is for indoor use only, for household
use only.
To protect against the risk of electrical shock, do not
immerse the unit, cord or plug in water or other liquid.
Please unplug before cleaning and maintenance the
appliance .
Use a soft cloth moisten with mild soap, and then use
a dry cloth to wipe it again.

This appliance must be earthed. In the event of a
malfunction or breakdown, grounding will reduce the risk
of anelectric shock by providing a path of least
resistance of electric current. This appliance is equipped
with a cord having an equipment-earthing conductor
and a earthing plug.
The plug must be plugged into an appropriate outlet that
is installed and earthed in accordance with all local
codes and ordinances.
Improper connection of the equipment-earthing
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the appliance
is properly grounded.
Do not modify the plug provided with the appliance;
If it does not fit the outlet.
Have a proper outlet installed by a qualified electrician.
Do not abuse, sit on, or stand on the door or dish rack of
the dishwasher.
Do not operate your dishwasher unless all enclosure
panels are properly in place.
Open the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
Do not place any heavy objects on or stand on the door
when it is open. The appliance could tip forward.
When loading items to be washed:
1) Locate sharp items so that they are not likely to
damage the door seal;

2) Warning: Knives and other utensils with sharp points
must be loaded in the basket with their points down or
placed in a horizontal position.
Check that the detergent comparment is empty after
completion of the wash cycle.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent.
For plastic items not so marked, check the manufacturer's
recommendations.
Use only detergent and rinse additives designed for
an automatic dishwasher.
Never use soap, laundry detergent, or hand washing
detergent in your dishwasher.
Children should be supervised to ensure that they do not
play with the appliance.
The door should not be left open, since this could increase
the risk of tripping.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
During installation, the power supply must not be
excessively or dangerously bent or flattened.
Do not tamper with controls.
The appliance is to be connected to the water mains using
new hose sets and that old hose-sets should not be reused.
The maximum number of place settings to be washed
is 6.
The maximum permissible inlet water pressure is 1MPa.
The minimum permissible inlet water pressure is 0.04MPa.

2
Dispose of the dishwasher packaging material
correctly.
All packaging materials can be recycled.
Plastic parts are marked with the standard
international abbreviations:
PE for polyethylene, e.g. sheet wrapping material
PS for polystyrene, e.g. padding
material POM polyoxymethylene, e.g.
plastic clips PP polypropylene, e.g.
Salt filler
ABS Acrylonitrile Butadiene Styrene, e.g. Control
Panel .
Packaging material could be dangerous for children!
For disposing of package and the appliance please
go to a recycling centre. Therefore cut off the power
supply cable and make the door closing device
unusable.
Cardboard packaging is manufactured from recycled
paper and should be disposed in the waste paper
collection for recycling.
By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences
for the environment and human health, which could
otherwise be caused by inappropriate waste handling
of this product.
For more detailed information about recycling of this
product, please contact your local city office and your
household waste disposal service.
DISPOSAL: Do not dispose this product as unsorted
municipal waste. Collection of such waste separately

3
for special treatment is necessary.

4
3
5
7
To get the best performance from your dishwasher, read all operating instructions
before using it for the first time.
43 4 45 8
1 2 6 7
Power Button: To turn on/off the power supply.
2 Delay Button : To press the button to delay.
Display screen: to show the reminding time
and the state(running state, delay time etc )
4 Rinse Aid Warning Light. : To be on when the
rinse aid dispenser needs to be refilled.
Salt Warning Light : To be on when the softener
needs to be refilled.
6 Washing Program Selector: Press the button
to select wash cycles.
Start/Pause Button: Press this button to start
or pause the dishwasher.
8 Program indicator light.
7 8
Front view
Back View
2
4 6
1 5 9 10
3
1 Salt Container 3 Cutlery Basket 5 Rinse Aid Dispenser 7 Cup Shelf 9 Inlet pipe connector
2 Detergent Dispenser 4 Filter assembly 6 Spray Arms 8 Basket 10 Drain pipe connector

5
If your model have no water softener, you may skip this section.
Always use salt intended for use with dishwasher.
The salt container is located beneath the basket and should be filled as follows:
Attention!
Only use salt specifically designed for use in dishwashers!All other types of
salt not specifically designed for use in a dishwasher, especially table salt, will
damage the water softener. in case of damages caused by the use of unsuitable
salt the manufacturer does not give any warranty nor is liable for any caused
damages.
Only fill with salt just before starting one of the complete washing programmes.
This will prevent any grains of salt or salty water, which may have been split,
remaining of the bottom of the machine for any period of time, which may cause
corrosion.
A Remove the basket and then unscrew and remove the cap from the salt container.
B Before first wash, add 1lt. of water in the salt container of your machine.
C Place the end of the funnel (supplied) into the hole and introduce about 1kg of salt.
It is normal for a small amount of water to come out of the salt container.
D After filling the container , screw the cap tightly back clockwise.
E Usually, the salt warning light will be cease to be illuminated within 2-6 days after the salt container has been filled with
salt.
F Immediately after filling the salt into the salt container, a washing programme should be started
Otherwise filter system, pump or other important parts of the machine may be damaged by salty
water. It is out of warranty.
1. The salt container must only be refilled when the salt warning light in the control panel comes on.
Depending on how fully the salt dissolves, the salt warning light may still be on even though the
salt container is filled.
If there is no salt warning light in the control panel (For some Models),you can judge when to load
the salt into the softener by the cycles that the dishwasher had run.
2. If there are spills of the salt, a soak or a rapid program should be run to remove the excess salt.
Adjusting Salt Consumption
Step 1: Enter the status of salt adjustment
Close the door, within 60 seconds after power on, press Start/Pause button and hold for 5 seconds,
the machine will enter setting mode.

6
Step 2: select a certain level of salt consumption
Press the Start/pause button to select the proper set according to your local environment,
the sets will change in the following sequence: H1->H2->H3->H4->H5->H6;
Step 3: Exit the status of salt adjustment
Without any operation in five seconds, the machine will exit from set mode, the machine is into standby status
There are 6 levels of salt consumption in all.It is recommended to select the level according to below table:
Water Hardness level
Setting on the
water softener
Digital display stalls
dH
1)
2)
mmol/l
0-5
0-0.9
1
6-11
1.0-2.0
2
12-17
2.1-3.0
3
18-22
3.1-4.0
4*
23-34
4.1-6.1
5
35-45
6.2-8.0
6
1)German degree of measurement for the water hardness
2)millimol, internationel unit for water hardness
*) factory setting
Contact your local water board for information on the hardness of your water supply.
Rinse Aid Dispenser
The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes. That can leave
spots and streaks. Italso improves drying by allowingwater to sheet off the dishes. Your dishwasher is designed to
use liquid rinse aids. The rinse aid dispenser is located inside the door next to the detergent dispenser. To fill the
dispenser, openthe cap andpour the rinse aid into the dispenser until the level indicator turns completely black.
The volume of the rinse aid container is about 110ml.
Function of Rinse Aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.

7
Function of Rinse Aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.
Attention!
Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.
When to Refill the Rinse Aid Dispenser
If there is no rinse-aid warning light in the control panel, you can judge the amount of rinse-aid by the color
of the optical level indicator
" "
located next to the cap. When the rinse-aid container is full, the whole
indicator will be dark .As the rinse-aid diminishes, the size of the dark dot decreases. You should never let
the rinse aid get below 1 / 4 full. C (Rinse-Aid indicator)
As the rinse aid diminishes, the size of the black dot
on the rinse aid level indicator changes, as illustrated below.
Full
3 / 4 full
1 / 2 full
1 / 4 full - Should refill to eliminate spotting
Empty
1
Toopen the dispenser, turn the cap to the "open" (left) arrow and lift it out.
2
Pour the rinse aid into the dispenser, being careful not to overfill.
3
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
Clean up any rinse aid split during filling with an absorbent cloth to avoid excessive foaming
during the next wash. Don't forget to replace the cap before you close dishwasher door.
Adjusting RinseAid Dispenser
The rinse aid dispenser has six or four settings. Always start with the dispenser
set on "4". If spots and poor drying are problems, increase the amount of rinse
aid dispensed by removing the dispenser lid and rotating the dial to "5". If the
dishes still are not drying properly or are spotted, adjust the dial to the next
higher number until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)
Increase the dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are sticky whitish stains on your dishes or a bluish film on glassware or
knife blades.
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the dishwasher.
Most of commercial quality detergents are suitable for this purpose.

8
Normally new pulverised detergent is without phosphate. The water softener function of
phosphate is not given. In this case we recommend to fill salt in the salt container even when
the hardness of water is only 6 °dH. If detergents without phosphate were used in case of hard water
often white spots appear at dishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Strong and coloured spots will not
removed completely. In this case please choose a programme with higher Temperature.
Concentrated Detergent
Based on their chemical composition, dishwasher can be split in two basic types:
conventional, alkaline detergents with caustic components
low alkaline concentrated detergents with natural enzymes
Detergent Tablets
Detergent tablets of different brands dissolve at different speeds. For this reason some
detergent tablets cannot dissolve and develop their full cleaning power during short
programmes. Therefore please use long programmes when using detergent tablets, to
ensure the complete removal of detergent residuals.
Detergent tablets are only for the models with 3 in 1 function or 3 in 1 program.
Detergent Dispenser
The dispenser must be refilled before the start of each wash cycle following the instructions
provided in the Wash Cycle Table . Your dishwasher uses less detergent and rinse aid then
conventional dishwasher. Generally, only one tablespoon of detergent is needed for
a normal wash load. Also, more heavily soiled items need more detergent. Always add the
detergent just before starting the dishwasher, otherwise it could get damp and will not
dissolve properly.
Amount of Detergent to Use
Push latch to open
If the lid is closed: press release button. The lid springs open.
Always add the detergent just before starting each wash cycle.
Only use branded detergent aid for dishwasher.

9
Dishwasher detergent is corrosive!
Take care to keep it out of reach of children.
Proper Use of Detergent
Use only detergent specifically made for use in dishwashers. Keep your detergent fresh and dry.
Don't put powder detergent into the dispenser until you're ready to wash dishes.
Fill in detergent A B
Fill the deter gent dispenser with deter gen t.
The mar king indicate s the dosing levels , as
illustrated on right:
A The place of main wash cycle detergent placed.
B The place of pre-wash cycle detergent placed.
Please observe the manufacturers dosing and storage
Recommendations as stated on the detergent packaging.
Close the lid and press until it locks in place.
If the dishes are heavily soiled, place an additional
detergent dose in the pre-wash detergent chamber. This detergent will take effect during the pre-wash phase.
You find information about the amount of detergent for the single programme on the last page.
Please aware, that according to the level soiling and the specific hardness of water differences are possible.
Please observe the manufacturer's recommendations on the detergent packaging.
Consider buying utensils which are identified as dishwasher-proof.
Use a mild detergent that is described as 'kind of dishes'. If necessary, seek further
information from detergent manufacturers.
For particular items, select a programme with as low a temperature.
To prevent damage, do not take glass and cutlery out of the dishwasher immediately
after the programme has ended.
Are not suitable Are of limited suitability
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not heat resistant
Older cutlery with glued parts that is not
temperature resistant
Bonded cutlery items or dishes
Pewter or copper items
crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
Some types of glasses can become
dull after a large number of washes
Silver and aluminium parts have a
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently

10
(For best performance of the dishwasher, follow these loading guidelines.
Features and appearance of baskets and cutlery baskets may vary from your model.)
Scrape off any large amounts of leftover food. Soften remnants of burnt food in pans
It is not necessary to rinse the dishes under running water.
Place objects in the dishwasher in following way:
1. Items such as cups, glasses, pots/pans, etc. are face down.
2. Curved items, or those with recesses, should be loaded at a slant so that water can
run off. 3.All utensils are stacked securely and can not tip over.
4. All utensils are placed in the way that the spray arms can rotated freely during washing.
Very small items should not be washed in the dishwasher as theycould easily fall out of the basket.
Load hollow items such as cups, glasses, pans etc. With the opening downwards so that
water cannot collect in the container or a deep base.
Dishes and items of cutlery must not lie inside one another, or cover each other.
To avoid damage to glasses, they must not touch.
Load large items which are most difficult to clean into the basket.
Long bladed knives stored in an upright position are a potential hazard!
Long and/or sharp items of cutlery such as carving knives must be positioned
horizontally in the basket.
Please do not overload your dishwasher. This is important for good results and for
reasonable energy consume.
Position the dishes and cookware so that they will not get moved by the spray of water.
1
Cups
3
Glasses
Medium serving bowl
Saucers
Dish Oval platter
Dinner plates Soup plates
10
Dessert dishes Cutlery basket
11
Serving spoons

11
Cutlery should be placed in the cutlery basket with handles at the bottom. If the rack has side baskets, the spoon
should be loaded individually into the appropriate slots, especially long utensils should be placed in the horizontal
position at the front of the upper basket as shown.
1 Forks
2 Soup spoons
3 Dessert spoons
4 Teaspoons
5 Knives
6 Serving spoons
7 Gravy ladles
8 Serving forks
Do not let any item extend through bottom.
Always load sharp utensils with the sharp point down!

12
Intensive
Normal
(*EN 50242)
For heaviest soiled crockery,
and normally soiled pots、
pans、dishes etc with dried
on soiling.
For normally soiled loads,
such as pots, plates,
glasses and lightly
soiled pans.
This is standard programme,
it is suitable to clean normally
soiled tableware and it is the
most efficient programme in
terms of its combined energy
and water consumption for
that type of tableware.
For lightly soiled loads,
Pre-wash(50℃)
Wash (70 ℃)
Rinse
Rinse
Rinse (70 ℃)
Drying
Pre-wash
Wash (60 ℃)
Rinse
Rinse (70 ℃)
Drying
Pre-wash
Wash (50 ℃)
Rinse
Rinse (70 ℃)
Drying
Wash (45 ℃)
Rinse
140
120
180
0.9
0.7
0.61
10
8
6.5
Glass such as glasses, crystal and
fine china. Rinse (60 ℃)
Drying 75 0.5 7.0
90 min
Rapid
For lightly soiled crockery
and glass.
Ashorter wash for lightly soiled
loads and quick wash.
This program provides an
Was h(65 ℃)
Rinse(70 ℃)
Drying
Wash (40 ℃)
Rinse
Rinse (40 ℃)
Wash (70 ℃)
Rinse
90
3~15g 30
15g
0.65
0.23
7.0
6
Self-Cleaning effective cleaning of the
dishwasher itself Rinse (65 ℃)
Drying (Or 1 pieces) 80 0.58 6.6
*EN 50242 : This programme is the test cycle. The information for comparability test
in accordance with EN 50242, as follows:
Capacity: 6 setting
Rinse aid setting: 6
The power consumption of off-mode is 0.45W
left-on mode is 0.49W
Starting a wash cycle...
Draw out the basket(see the section entitled “Loading the Dishwasher”).
Pour in the detergent (see the section entitled “Salt,
Detergent and Rinse Aid”).
Insert the plug into the socket. The power supply is 220-240
VAC 50 HZ, the specification of the socket is 10 A250 VAC.
Make sure that the water supply is turned on to full pressure.
Press the program button , the wash program will be changed as follows direction
ECO->Glass->90 min->Rapid->Self-Cleaning->Intensive->Normal;
If a program is selected, the response light will light. Then press the
Start/Pause button, the dishwasher begins to start.
When you press the Start/Pause button to pause during washing,
the program light will stop blinking and the dishwasher will mooing
every minute unless you press the Start/Pause button to start.

13
Premise: You can modify the washing program, When the dishwasher just
runs for a short time. Otherwise, the detergent may have already been
released, and the appliance may have already drained the wash water. If this
is the case, the detergent dispenser mus t be refilled (see the section entitled
" Loading the Detergent " ).
Press Start/Pause Button to pause the machine when the door is closed ,Press
Program Button more than three seconds the machine will be in stand by state ,
then you can change the program to the desired cycle setting (see the section
entitled " Starting a wash cycle. . ." ).
NOTE: If you open the door during washing, the machine will pause. When you
close the door and press the Start/Pause Button, the machine will keep on
working after 10 seconds.
The program lights show the state of the dishwasher:
a)One of the program lights on----------stand by or pause
b)One of the program lights blinking----- run
If you open the door when washing, the machine will pause. When you close the door , the machine
will keep on working after 10 seconds.
Aforgotten dish can be added any time before the detergentcup opens.
1Press the Start/Pause button
2 Open the door a little to stop the washing.
3 After the spray arms stop working,you can open the door
completely.
4 Add forgotten dishes.
5 Close the door
6 Press the Start/Pause button, the dishwasher will run
after 10 seconds.
When the working cycle has finished, the buzzer of dishwasher will sound 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they
are still hot and more susceptible to breakage. They will also dry better.
Switch Off the Dishwasher
1. Switch off the dishwasher by pressing the ON/OFF
button. 2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
It is dangerous to open the door when washing,
because the hot water may scald you.

14
The filter prevent larger remnants of food or other objects from getting inside the pump.
The filter system consists of a coarse filter, a flat (Main filter)
and a micro filter (fine filter).
CMain filter
Food and soil particles trapped by this filter are pulverized by a
special jet on the spray arm and washed down to drain.
B Fine filter
This filter holds soil and food residue in the sump area and
prevents it from being deposited on the dishes during wash cycle.
A Coarse filter
Larger items, such as pieces of bone or glass, that could block
the drain are trapped in the coarse filter. To remove the items
caught by the filter, gently squeeze the tap on the top of this
filter and lift out.
Filter assembly
The filter efficiently removes food particles from the wash water, allowing it to be re-cyclated during the cycle.
For best performance and results, the filter assembly must be regularly. For this reason, it is a good idea to
remove the larger food particles trapping in the filter after each wash cycle by rinsing the filter and cup under
running water. To remove the filter assembly, pull on the cup handle in the upward direction.
Never run the dishwasher without the filters in place.
The dishwasher must never be used without the filters.
Improper replacement of the filter may reduce the performance level of the appliance
and damage dishes and utensils.
Step1：contrarotate the filter assembly(A,B and C),
then lift it all up.
C
BStep2: lift B and C up from A;
A
C
B The End.
A
If do it from step1 to step 3, the filter system will be removed; while if do it from Step 3 to Step 1,
the filter system will be installed.

15
Remarks:
- Inspect the filters for blocking every time the dishwasher has been used.
- By unscrewing the coarse filter.you can remove the filter system.Remove any food remnants and
clean the filters under running water.
The entire filter assembly should be cleaned once a week.
Cleaning The Filter
To clean the coarse filter and the fine filter, use a cleaning brush. Reassemble the filter parts as shown in the figures
in the last page and reinsert the entire assembly in the dishwasher, positioning in its seat and pressing downward.
When cleaning the filters, don't knock on them. Otherwise, the filters could be
contorted and the performance of dishwasher could be debased.
The control panel can be cleaned by using a lightly dampened cloth and dry thoroughly.
The exterior use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Cleaning The Door
To clean the edge around the door, you should use only a soft warm,
damp cloth. To avoid penetration of water into the door lock and
electrical components, do not use a spray cleaner of any kind.
Never use a spray cleaner to clean the door panel as it may damage the door lock
and electrical components.
Abrasive agent or some paper towel should not be used because of the risk of
scratching or leaving spots on the stainless steel surface.
ProtectAgainst Freezing
please take frost protection measures ondishwasher in winter. Each time after washing cycles,
please operate as follows：
1. Cut off electrical power to the dishwasher.
2. Turn off the water supply and disconnect the water inlet pipe from the water
valve. 3.Drain water from the inlet pipe and water valve. (Use a pan to catch the
water)
4. Reconnect the water inlet pipe to the water valve.
5. Remove the filter at the bottom of the tub and use a sponge to use up water in sump.
If your dishwasher cannot work because of the ice, please contact professional service persons.