Morrison EK 2040 User manual

1
571732 - Electric Chainsaw 2000W Owner’s Manual - June ‘14
Pantone 1797C
Pantone Cool Gray
8C
Pantone 426C
www.morrisonoutdoor.com
Electric Chainsaw
2000W
Owner’s Manual
Important
Please read this Owner’s Manual and the Express Warranty before using this product. The Warranty does
not cover damage due to misuse or failure to follow the operating and installation instructions.
Keep the instructions in a safe place for future use.
Part No: 571732
Revised June 2014

2
571732 - Electric Chainsaw 2000W Owner’s Manual - June ‘14

3
571732 - Electric Chainsaw 2000W Owner’s Manual - June ‘14
Do not operate this machine before it has been
assembled correctly and you have read and understood
these instructions.
These instructions are intended asa general guide and do
not super-sede national or local codes in anyway. Contact
local Authorities forclarity of laws relating to operationof
this appliance.
Keep the instructions in a safe place for future use.
Contents
Symbols in this Owner’s Manual 4
Proper Use 4
Safety Instructions 4
Transporting the Chainsaw 5
Before Starting Up 5
List of Parts 6
Assembling the chain bar and saw chain 6
Maintaining the chain 6
Starting Up 7
Operation 7
Maintenance and cleaning 9
Specifications 10
Troubleshooting 10
Wear eye protection
Caution! Read the operating
instructions and follow
the warnings and safety
instructions.
Wear ear protection
Do note expose to rain
Remove plug from the
mains immediately if the
cable is damaged or cut
Maximum cutting
length: max. 400mm.
400mm

4
571732 - Electric Chainsaw 2000W Owner’s Manual - June ‘14
Symbols in the Owner’s Manual
Threatened hazard or hazardous situation.
Not observing this instruction can lead to injuries or cause
damage to property.
Important information on proper handling.
Not observing this instruction can lead to faults
in the machine.
User information. This information helps you to use all
the functions correctly.
Proper Use
For safety reasons, the Brushcutters are not to be
used by children, young people under 16 years of
age, or any other persons who are not acquainted
with these directions for use.
Specific safety information Please read this safety
information and the directions for use carefully and
be sure to follow the instructions to the letter.
Safety Instructions
WARNING Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There is an
increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use of
an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power tool
while you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment.Always wear eye
protection. Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/or
battery pack, picking up or carrying the tool. Carrying power
tools with your finger on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can reduce
dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making any
adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other condition
that may affect the power tool’s operation. If damaged, have
the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account the
working conditions and the work to be performed. Use of the
power tool for operations different from those intended could result
in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that the
safety of the power tool is maintained.
Chain saw safety warnings:
– Keep all parts of the body away from the saw chain when the
chain saw is operating.
Before you start the chain saw, make sure the saw chain is not
contacting anything. A moment of inattention while operating chain
saws may cause entanglement of your clothing or body with the
saw chain.
– Always hold the chain saw with your right hand on the rear
handle and your left hand on the front handle. Holding the

5
571732 - Electric Chainsaw 2000W Owner’s Manual - June ‘14
chain saw with a reversed hand configuration increases the risk of
personal injury and should never be done.
– Hold the power tool by insulated gripping surfaces only,
because the saw chain may contact hidden wiring or its own
cord. Saw chains contacting a “live” wire may make exposed metal
parts of the power tool “live” and could give the operator an electric
shock.
– Wear safety glasses and hearing protection. Further protective
equipment for head, hands, legs and feet is recommended.
Adequate protective clothing will reduce personal injury by flying
debris or accidental contact with the saw chain.
– Do not operate a chain saw in a tree. Operation of a chain saw
while up in a tree may result in personal injury.
– Always keep proper footing and operate the chain saw only when
standing on fixed, secure and level surface. Slippery or unstable
surfaces such as ladders may cause a loss of balance or control of
the chain saw.
– When cutting a limb that is under tension be alert for spring
back. When the tension in the wood fibres is released the spring
loaded limb may strike the operator and/or throw the chain saw out
of control.
– Use extreme caution when cutting brush and saplings. The
slender material may catch the saw chain and be whipped toward
you or pull you off balance.
– Carry the chain saw by the front handle with the chain saw
switched off and away from your body. When transporting or storing
the chain saw always fit the guide bar cover.
Proper handling of the chain saw will reduce the likelihood of
accidental contact with the moving saw chain.
– Follow instructions for lubricating, chain tensioning and
changing accessories. Improperly tensioned or lubricated chain
may either break or increase the chance for kickback.
– Keep handles dry, clean, and free from oil and grease.
Greasy, oily handles are slippery causing loss of control.
– Cut wood only. Do not use chain saw for purposes not intended.
For example: do not use chain saw for cutting plastic, masonry or
non-wood building materials. Use of the
chain saw for operations different than intended could result in a
hazardous situation.
Causes and operator prevention of kickback:
Kickback may occur when the nose or tip of the guide bar touches
an object, or when the wood closes in and pinches the saw chain in
the cut.
Tip contact in some cases may cause a sudden reverse reaction,
kicking the guide bar up and back towards the operator.
Pinching the saw chain along the top of the guide bar may push the
guide bar rapidly back
towards the operator.
Either of these reactions may cause you to lose control of the saw
which could result in serious personal injury. Do not rely exclusively
upon the safety devices built into your saw.
As a chain saw user, you should take several steps to keep your
cutting jobs free from accident or injury.
Kickback is the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below:
– Maintain a firm grip, with both hands thumbs and fingers
encircling the chain saw handles, and position your body and
arm to allow you to resist kickback forces. Kickback forces can
be controlled by the operator, if proper precautions are taken. Do
not let go of the chain saw.
– Do not overreach and do not cut above shoulder height.
This helps prevent unintended tip contact and enables better
control of the chain saw in unexpected situations.
– Only use replacement bars and chains specified by the
manufacturer. Incorrect replacement bars and chains may cause
chain breakage and/or kickback.
–Follow the manufacturer’s sharpening and maintenance
instructions for the saw chain. Decreasing the depth gauge
height can lead to increased kickback.
It is recommended that the tool always be supplied via a
residual current device with a rated residual current of 30 mA
or less If the replacement of the supply cord is necessary,
this has to be done by the manufacturer or his agent in order
to avoid a safety hazard.
Transporting the chainsaw
Before transporting the chainsaw, always remove the plug from the
power socket and slide the chain guard over the bar and chain.
Before starting up
The voltage and current supply must comply with the ratings on
the type plate. Before commencing work, always check that the
chainsaw works properly and is safe to operate. Check also that
the chain lubrication and the oil guard are in good working order.
When the oil level is approximately 5mm above the bottom (Min)
mark, you must top up the oil. Check the chain tension and adjust
if necessary refer Tensioning the Saw Chain. Verify that the chain
brake is working correctly.

6
571732 - Electric Chainsaw 2000W Owner’s Manual - June ‘14
Assembling the chain bar
and saw chain
1. Remove the plastic shield
2. Place the chain around the nose wheel of the bar
Place the bar onto the engine unit and fit the chain around the
bar
3. Make sure that the chain is turned the right way (forward).
4. Mount the plastic shield
5. Tighten the shield nut with your fingers.
6. Lift the tip of the bar and tighten the chain using the yellow ring
around the shield nut.
The chain shall be tightened so that you can just lift the driving
link free of the trace of the bar.
7. Fastened the bar and shield cover securely.
Nose wheel
Chain wheel and bar
before mounting the
chain
Chain wheel and bar
after mounting the chain
Tensioning the saw chain
Always pull the plug out of the power socket beforedoing
any work on the machine! Wear safety gloves!
Check the chain tension regularly. Do not tension the chain too
tightly. When cold, it should be possible to lift the chain in the
middle of the chain bar approx. 5mm. Tighten the hand wheel
securely. When warm, the saw chain will expand and slacken and
there is a danger of it jumping off the rail altogether.
Re-tension if necessary. If the saw chain is re-tensioned when
hot, it may need loosening again when the sawing work has been
completed. Otherwise, the contraction that takes place, as the
chain cools might result in an excessively high tension. A new
saw chain requires a running-in period of approx 5 minutes. Chain
lubrication is very important at this stage. After running in, check
chain tension and re-tension if necessary.
Maintaining the chain
Adding chain oil
To prevent dirt getting inside the tank, clean the oil tank cap before
opening. Check the contents of the oil tank duringsawing work by
checking the oil gauge. Close the oil tank cap tightly and wipe away
any spills.
Chain lubrication
To prevent excessive wear, the saw chain and chain bar must be
evenly lubricated during operation. Lubrication is automatic. Never
work without chain lubrication. If the chain runs dry, the chain bar
and chain will quickly beseverely damaged. It is therefore important
to check the chain lubrication before every use. Never use the saw
when the oil level is below the “Minimum” mark.
• Minimum - When only approx 5mm oil is visible at the lower rim
of the oil gauge, you must top up with oil.
• Maximum - Top up with oil until the window is full.
1
2
3
4
98
7
6
5
List of Parts
1. Throttle control
2. Oil tank cover
3. Chain brake
4. Chain
5. Holder for electric cord
6. Indicator for oil
7. Adjustment of chain
(no tools necessary)
8. Bar
9. Hold for lubrication

7
571732 - Electric Chainsaw 2000W Owner’s Manual - June ‘14
Checking the automatic lubrication
Before commencing work, verify the oil supply and check the
automatic chain lubrication. Switch on the chainsaw and holdit
above light-coloured ground. Be careful not to allow thechainsaw to
touch the ground. (For safety reasons it is best tokeep a clearance
of at least 20cm). If you now see growingtraces of oil on the ground,
the chain lubrication system isworking correctly. If there are no
traces of oil, clean the saw-dust from the oil outlet and the upper
chain-tensioning borehole.
Chain lubricants
The service life of saw chains and chain bars depends to alarge
extent on the quality of the lubricant used. Old oil must not be used!
Use only environment-friendly chain lubricant. Store chain lubricant
only in containers, which comply with the regulations.
Chain bar
The chain bar is subjected to wear and tear at the noseand on the
bottom. To avoid one-sided wear and tear, turn thechain bar over
every time you sharpen the chain.
Chain wheel
The chain wheel is subjected to especially high wear andtear. If
you notice deep wear marks on the teeth, the chainwheel must be
replaced. Aworn chain wheel curtails the ser-vice life of the saw
chain.
Chain guard
The chain guard must be clipped onto the chain bar assoon as the
sawing work has been completed and wheneverthe machine has to
be transported.
Chain brake
In the event of kick-back, the chain brake will be actuated viathe
front guard. The front guard is pushedforwards by the back of the
hand and this causes the chainbrake to stop the chainsaw.
Testing the chain brake
Test the chain brake in the following way:
1. Place the saw on a solid
foundation.
2. Start the engine.
3. Keep right hand on the
rear handle.
4. Keep left hand on the
front handle.
5. Start the engine and activate the chain brake be pulling the
chain brake forward.
6. The chain must stop instantly. When it stops, release the
throttle control.
7. If the chain brake works, stop the engine and release the chain
brake by pushing it forward in deactivated position.
Releasing the chain brake
To be able to use your chainsaw again, you must release thechain
brake again. First switch off the machine. Then pull the front the
front guard back into the vertical position until itlocks in place. The
chain brake is now fully functional again.
Adjustment of chain with no use of tools
Loosen the shield nut and
turn the yellow ring clockwise
to tighten and anti-clockwise
to loosen the chain. Fasten
the shield nut afterwards.
Sharpening the saw chain
You can have your saw chain sharpened fast and correctly by
specialist dealers, from whom you can also obtain chain sharpening
equipment to enable you to sharpen the chain yourself. Please
follow the corresponding operating instructions.
Take care of your tools. Keep your tools sharp and
clean to enable you to work well and safely. Follow the
maintenance regulations and the instructions forchanging
tools.
Starting up
Always wear safety goggles, earmuffs, protective
gloves and sturdy work clothes!
Use the saw only with approved extension
cables which have the prescribed insulationand
connections designed for outdoor use. To switch on,
hold the front grip with your left hand, and the rear
grip with your right hand.
Simultaneously press the safety lock-off and
squeeze the ON/OFF switch. Check to ensure the
chain brake is working properly.
If the chainsaw does not run, the chain brake must
be released at the front finger guard. Be sure to read the sections
“Chain brake” and “Releasing the chain brake”on this point.
After switching on, the chainsaw will run immediately at highspeed.
To switch off: Release the ON/OFF switch. Only put down the chain
saw after the chain has stopped rotating!
After working with the chainsaw, you should always: Clean the saw
chain and chain bar. Attach the chain guard.
Warning!
Never use the machine in the rain or in
damp conditions.
If the extension cable is damaged, pull the plug out of the power
socket immediately. Never work with a damaged cable. Check
the machine for damage. Before using your tool again, check the
safety devices to ensure that they are in good working order. Make
sure the moving parts are working correctly. All parts must be
correctly assembled to ensure that the machine works correctly.
Any damaged safety devices andparts must be properly repaired or
replaced immediately
Operation
Kick-back
You can avoid accidents by notsawing
with the tip of the chain baras this may
cause the saw to rearup suddenly.
Always use the complete safety
equipment when working with the
saw. Kick-back is an upward and/or
backward movement of the chainbar
which can occur if the saw chain at
the tip of the chain bar encounters an
obstruction.
Make sure your work-piece is firmly secured. Use clamps tostop the
work-piece shifting. Never attempt to hold the work-piece with one
hand while operating the saw with the other!
Kick-back causes the saw to behave uncontrollably with the risk
of serious injury. Never saw with a slack or blunt chain. A poorly
sharpened chain increases the risk of kickback. Never saw above
shoulder height.

8
571732 - Electric Chainsaw 2000W Owner’s Manual - June ‘14
Tips on chainsaw use
Sawing up firewood (See Figure 4 and 5)
Please observe the safety regulations and proceed as follows:
Make sure the wood to be sawed cannot slip. Clamp short pieces
of wood in place before sawing. Saw only wood. When sawing,
make sure that no stones or nails are touched as these could be
thrown out and may also damage the saw chain. Avoid bringing
the running saw into contact with wire fences or the ground. When
lopping off branches, support the machine as far as possible and
do not saw with the tip of the chain bar. Watch out for obstacles on
the ground such as tree roots, ditches and hillocks as these could
cause you to fall.
Important!
The chainsaw must be running before it comes into
contact with the wood!
To switch on: Press the saw safety lock-off and squeezethe ON/
OFF switch. Place the lowest claw on the wood. Raise the chainsaw
by the rear grip as you lowerthe saw into the wood. Move the
chainsaw back a little and place the claw further down. Be careful
when sawing splintered wood as pieces of wood may be ripped off.
To switch off: Release the ON/OFF switch.Pull the plug out of the
power socket.
Wood under tension
Tree trunks can be under great tension when lying on theground,
and they can spring dangerously when cut. Always cut the side that
is under compression first, and then the side under tension. See
Figures 10, below.
Felling trees
To fell trees, observe all the safety regulations and proceed as
follows:
The chainsaw may be used to fell only trees which are smaller in
diameter than length of the chain bar. Never try to extract a jammed
saw with the motor still running. If the saw chaingets jammed,
release it using a wooden wedge.
Important!
Danger zone: Falling trees can bring down other treeswith
them. The danger zone is therefore twice thelength of the
tree being felled. (Figure 11)
Felling trees is dangerous and requires practice. If you are a
beginner or inexperienced, do not try to teach yourself butseek
professional training. (Figure 12)
Felling direction:
• First estimate the direction of fall, taking into account the centre
of gravity of the crown and the wind direction.
• The chainsaw must be running before it comes into contact
with the wood. Switch on the chainsaw. Saw an undercut in
the tree in the direction of fall and then make a horizontal cut
(back cut) on the side opposite to the undercut.
• Make the undercut: This will give the tree direction and
guidance.
• Check the direction of fall: if you have to correct the undercut,
always recut over the entire width.
• Call out “Timber!”
• Only now make the back cut, which must be higher than
thesole of the undercut. Insert wedges in good time.
• Leave the bridge in place as it will function as a hinge. If you
cut through the bridge, the tree will fall randomly.
• Fell the tree by driving a wedge into the back cut, not by
sawing through the bridge.
• When the tree falls, step back and watch the crown. Wait for
the crown to stop swinging. Do not continue working under
branches, which have got stuck.
Do not fell trees:
• If you can no longer distinguish details within the danger zone,
e.g. owing to fog, rain, snow drifts or twilight.
• If the direction of fall cannot be reliably estimated owing to
wind or gusts of wind. Felling work on sloping ground, black
ice, frozen or dewy ground is safe only if you can get a firm
foothold.
Limbing a tree
Limbing is removing the branches from a fallen tree. When limbing
leave larger lower limbs to support the log off the ground. Remove
the small limbs in one cut as illustrated in Figure 13. Branches under
tension should be cut from the bottom up to avoid binding the chain
saw.
Figure 13 - Tree Limbing

9
571732 - Electric Chainsaw 2000W Owner’s Manual - June ‘14
Bucking a log
Bucking is cutting a log into lengths. It is import ant to make sure
your footing is firm and your weight is evenly distributed on both
feet. When possible, the log should be raised and supported by the
use of limbs, logs or chocks. Follow the simple directions for easy
cutting.
When the log is supported along its entire length as illustrated in
Figure14, it is cut from the top (overbuck).
Figure 14 - Log supported along the entire length
When the log is supported on one end, as illustrated in Figure 15,
cut 1/3 the diameter from the underside (underbuck). Then make
the finished cut by overbucking to meet the first cut.
Figure 15 - Log supported one end
When the log is supported on both ends, as illustrated in Figure
16, cut 1/3 the diameter from the top (overbuck). Then make the
finished cut by underbucking the lower 2/3 to meet the first cut.
Figure 16 - Log supported both ends
When bucking on a slope always stand on the uphill side of the
log, as illustrated in Figure 17. When “cutting through”, to maintain
complete control release the cutting pressure near the end of the
cut without relaxing your grip on the chain saw handles. Don’t let
the chain contact the ground. After completing the cut, ‘wait for the
saw chain to stop before you move the chain saw. Always stop the
motor before moving from tree to tree.
Figure 17 - Bucking a log
After Completion of work:
• Switch power off at main supply.
• Clean, check and coil extension lead.
• Clean, check and sharpen saw if required, oil chain and fit
chain guard.
• Store item in a safe place.
Maintenance and cleaning
Always pull the plug out of the power socket before doing any work
on the machine!
Keep the cooling vents on the motor housing clean and
unobstructed at all times. Only the maintenance work described in
these operating instructions may be carried out.
Storage
Keep your chainsaw in a safe place. The machine should be stored
clean, with the chain guard fitted, on a flat surface and in a dry
place inaccessible to children.

10
571732 - Electric Chainsaw 2000W Owner’s Manual - June ‘14
•Call out “Timber!”
•Only now make the back cut, which must be higher than the
sole of the undercut. Insert wedges in good time.
•Leave the bridge in place as it will function as a hinge. If
you cut through the bridge, the tree will fall randomly.
•Fell the tree by driving a wedge into the back cut, not by
sawing through the bridge.
•When the tree falls, step back and watch the crown. Wait
for the crown to stop swinging. Do not continue working
under branches, which have got stuck.
After Completition of work:
• Switch power off at main supply.
• Clean, check and coil extension lead.
• Clean, check and sharpen saw if required,
oil chain and fit chain guard.
• Store item in a safe place.
Do not fell trees:
•If you can no longer distinguish details within the danger
zone, e.g. owing to fog, rain, snow drifts or twilight.
•If the direction of fall cannot be reliably estimated owing to
wind or gusts of wind. Felling work on sloping ground, black
ice, frozen or dewy ground is safe only if you can get a firm
foothold.
Maintenance and cleaning
Always pull the plug out of the power socket before doing any
work on the machine!
Keep the cooling vents on the motor housing clean and unob-
structed at all times. Only the maintenance work described in
these operating instructions may be carried out.
Storage
Keep your chainsaw in a safe place. The machine should be
stored clean, with the chain guard fitted, on a flat surface and
in a dry place inaccessible to children.
Specifications
Rated voltage 240V~50Hz
Rated power 1800W
Bar length 405mm
Chain speed at no-load 12m/s
Max. Sound power level 107db(A)
Protection class II/_
8
Troubleshooting
ydemeResuaCtluaF
.gulpdnaelbac,tekcoskcehCyticirtceleoNnurtonseodrotoM Chain brake Damaged cable: Have cable replaced. It is prohibited
to patch the cable with insulating tape. Damaged
switches have to be replaced by a qualified workshop.
See section Maintaining the chain, “Chain brake” and
“Releasing the chain brake”, page 6.
Chain does not move Chain brake Check the chain brake, release if necessary.
Poor cutting performance Blunt chain Sharpen the chain
Chain wrongly fitted Check that the chain is fitted correctly
Chain tension Check the chain tension
Saw works only with difficulty Chain tension Check the chain tension
Chain jumps off. levelliokcehCnoitacirbulniahCtohsemocebniahC Check chain lubrication
Sharpen the chain
Specifications
Model Chain saw EK 2040
Output 230 V, 2000 Watt
Revolutions 6.000 - 7.000 / min
Contents of tank 390 ml
Lubrication Automatic
Anti-vibration Yes
Weight 4.8 kg
Length of bar 16” / 40 cm
Chain speed 13.5 m/s
Chain brake Yes
Hand shield Yes
Chain Spare part no. Tex-chain 250 (57 joints) 40-250

11
571732 - Electric Chainsaw 2000W Owner’s Manual - June ‘14

12
571732 - Electric Chainsaw 2000W Owner’s Manual - June ‘14
Head Office - New Zealand
1-37 Mt Wellington Highway, Panmure, Auckland 1060
P.O. Box 14 349, Panmure, Auckland 1741