mothercare little hampton changing unit User manual

little hampton
changing unit
user guide
important!
retain for future reference –
read carefully

1 introdduccion1
1 important notes
Lay the parts out and compare to the PARTS CHECKLIST below. Do not discard and packaging until you are
sure that you have all the parts.
This furniture is provided with an anti-topple device for securing to a wall. Failure to use this could result in the
furniture toppling onto a child.
A Mothercare changing mat is recommended for use with this changing unit with maximum dimensions of
82cm x 48cm. Place the mat evenly between the top rails.
1
introduction introduccion
1
introduction introduccion
1
introduction introduccion
1
introduction introduccion
1
introduction introduccion
parts checklist
1
introduction introduccion
2parts checklist
1
introduction introduccion
2parts checklist
1
introduction introduccion
2parts checklist
1
introduction introduccion
2parts checklist
14 cross head screws 7 x 45mm
61 dowels
26 cam screws
8, 4 x 25mm domed head screws
4 M6 x 14mm screws
2 M6 x 36mm screws
2 blanking screws
2 washers
33, 3 x 16mm cross head screws
26 cams
1, 4 x 16mm cross head screws
4 handles
5 back panel plates
1 strap
2 back plates
1

1introdduccion
2parts checklist
2 side rails
1 back rail
1 centre panel
1 large back panel
1 base
1 base rail
2 drawer fronts
1 top
1 rear support rail
1 front rail
1 shelf
2 sides (left and right)
4 drawer sides
1 small back panel
2

1introdduccion
2parts checklist
1
1
1
1
1
12
12
12
1
2 drawer backs
2 drawer bases
tools required:
1 allen key (provided)
2 drawer supports
1 cross head screw driver
3
1 introduction introduccion
3assembly
1

1 introduction introduccion
3assembly
4
Insert 2 dowels in to the centre panel.
Align the dowles in the center panel with
their corresponding pre-drilled holes on
the shelf and push firmly in to position.
Insert 2, 7 x 45mm screws in to the shelf
and tighten with the cross head screws
driver.
attaching the center panel to the shelf
1
Insert 7 dowels into the base rail and
base.
Insert 2 cam screws in to the base rail.
Insert 2 cams in to the base.
Attach the base rail to the base by
locating the dowels and cam screws in to
their corresponding pre-drilled holes and
push firmly into position.
Lock the cams in to place using the
cross head screw driver by turning these
in a clockwise direction 180 degrees.
attaching the base rail to the base
2

1 introduction introduccion
3assembly
5
Insert 4 dowels into the shelf.
Insert 2 cam screws in to the side.
Insert 2 cams in to the shelf.
Attach the shelf to the side by locating
the dowels and cam screws in to their
corresponding pre-drilled holes and
push firmly into position.
Lock the cams in to place using the cross
head screw driver by turning these in a
clockwise direction 180 degrees.
attaching the shelf to the side
3
Insert 6 dowels into the base and back
support rail.
Insert 2 cam screws in to the side.
Insert 2 cams in to the base.
Attach the base to the side by locating
the dowels and cam screws in to their
corresponding pre-drilled holes and
push firmly into position.
Lock the cams in to place using the cross
head screw driver by turning these in a
clockwise direction 180 degrees.
Attach the back support rail to the side by
locating the dowel in to the corresponding
pre-drilled hole and push firmly into
position.
attaching the base and back support rail to the side
4

1 introduction introduccion
3assembly
6
Insert 4 cam screws in to the side.
Insert 4 cams in to the base and shelf.
Attach the base, shelf and back support
rail to the side by locating the dowels and
cam screws in to their corresponding
pre-drilled holes and push firmly into
position.
Lock the cams in to place using the cross
head screw driver by turning these in a
clockwise direction 180 degrees.
attaching the second side
5
THE LITTLE HAMPTON CHANGING
UNIT IS SUPPLIED WITH AN
ANTI-TOPPLE DEVICE THAT SECURES
TO THE WALL. FAILURE TO USE THIS
COULD RESULT IN THE FURNITURE
TOPPLING OVER. WE RECOMMEND
THAT YOU USE THIS SAFETY DEVICE.
Attach the small back panel to the back
of the changing unit using 9, 3 x 16mm
screws. Tighten with the cross head
screw driver.
Using 1, 4 x 16mm screw, 2 washers and
1 strap, fix to the rear of the changing unit
as indicated in the diagram using a cross
head screw driver.
The loose end of the strap requires fixing
to the wall where the furniture will be
positioned. Certain wall materials require
different types of mounting hardware (e.g.
plastic rawl plugs, plasterboard rawl plugs).
Select mounting hardware suitable for the
walls in your home. If you are unsure what
type of mounting hardware required
please consult your local DIY store for
advice. Installation only to be carried out
by a competent person.
attaching the small back panel and strap
6

1 introduction introduccion
3assembly
7
Attach the large back panel to the back
of the changing unit using 16, 3 x 16mm
cross head screws and the 5 back panel
plates
attaching the large back panel
7
Insert 16 dowels into the sides, center
panel and back support rail.
Insert 6 cam screws in to the top.
Insert 6 cams in to the sides and center
panel.
Attach the top to the sides, center panel
and back support rail by locating the
dowels and cam screws in to their
corresponding pre-drilled holes and
pushing firmly into position.
Lock the cams in to place using the cross
head screw driver by turning these in a
clockwise direction 180 degrees.
attaching the top
8

1 introduction introduccion
3assembly
8
Insert 5 cam screws in to each of the
drawer front. Insert 4 dowels in to each
of the drawers backs. Insert 2 dowels in
to each of the drawer sides.
Attach the drawer back to the drawer
sides by inserting the dowels in to their
pre-drilled holes and pushing firmly
together. Secure using 8, 7 x 45mm screws
tightening with a cross head screw driver.
Attach the drawer front by aligning the
dowels and cam screws to their
corresponding pre-drilled holes and push
firmly in place.
Insert 8 cams in to their pre-drilled holes
and lock in place using the cross head
screw driver by turning these in a
clockwise direction 180 degrees.
assembling the drawer back, sides and front
9
Slide each drawer base in the grooves on
the drawer sides and push into the
grooves on the drawer front. Secure using
4, 3 x 16mm screws for each drawer.
Insert 1 dowel and 1 cam in to each
drawer support. Attach the drawer support
by aligning the dowels and cam screws to
their corresponding pre-drilled holes and
firmly push in place
Lock the cams in place using the cross
head screw driver by turning this in a
clockwise direction 180 degrees.
Attach the drawer support to the drawer
back using 4, 7 x 45mm cross head screw
tightening with the cross head screw driver.
Attach the handles to the drawers using 2
M4 x 25mm domed head screws for each
drawer.
Locate the drawers in the base unit by
carefully aligning the rear drawer runner
wheels on to the front runner wheels of
the base unit. Slide drawers in base.
Attaching the drawer support, base and handles
10

1 introduction introduccion
3assembly
Insert 8 dowels in to the front and back
rail.
Attach the front and back rail to the side
rails by pushing firmly into place.
Place the top rails on to the changing
unit top and secure on the underside with
2 x m6 x 36mm screws using the Allen
key provided.
Secure the back plates to the changing
unit sides using 2 x M6 x 14mm screws
using the Allen key provided.
attaching the changing unit top rails
11
9
It is possible to remove the side rails
and front rail of the changing unit to
make in to a dresser.
Remove the 2 underside M6 x 36mm
screws using the Allen key provided.
Remove the M6 x 36mm screw from the
rear sides and remove the top rails.
Insert 2 blanking screws in to the
changing unit top and secure using
2 x M6 x 14mm screws using the Allen
key provided.
Please carefully wrap the top rails in
protective packaging and stow away in a
safe place with all spare fittings in case
these will be required for future use.
changing to a dresser
12