Motoalliance Impact Trailer 100 User manual

Note Slanted Portion of Trailer Tub Face Towards the Rear
MODEL #
UPC
DESCRIPTION:
MOTOALLIANCE - WWW.MOTOALLIANCE.COM - [phone]
Impact Trailer 100

ITEM
NO.
PART NUMBER DESCRIPTION QTY.
1 IT104 Trailer Tub 1
2 IT105 Main Frame 1
3 ITA213 Axle Assembly 1
4 ITA134 Backer Plate 1
5 ITA-306 Hitch Tube Pivot Bracket 1
6 IT106 Hitch Tube Saddle Bracket 1
7 ITA-305 Hitch Assembly 1
8 ITA160 1/2" Carriage Bolt Plate 4
Hardware List
10 Regular FW 0.5 .50" Flat Washer 9
11 Lynch Pin Linch Pin 5/32" Dia. 2
12 Regular LW 0.5 .50" Lock Washer 9
13 HNUT 0.5000-13-D-N 1/2"-13 Hex Nut 9
14 .50-13 3.50 Carriage Bolt 1/2-13 x 3.50" Carriage Bolt 5
15 .50-13 1.25 Carriage Bolt 1/2-13 x 1.25" Carriage Bolt 4
16 Regular FW 1
1" Flat Washer 1/8"
Thickness
2
17 625 Hitch Pin
5/8" Dia. Bent Hitch Pin /
Snap Clip
1
18 ITA131
Tire Wheel Kit - 18" x 8.50" x
8.00" With 1" ID Bearing
2
MODEL #
UPC
DESCRIPTION:
MOTOALLIANCE - WWW.MOTOALLIANCE.COM - [phone]

Place Trailer Tub on Flat Surface Open Face Down.
Note Slanted Portion of Trailer Tub Face Towards the Rear
Note: Prior to Final Assembly of Tub onto Frame
It will be required to drill (4) 9/16" dia. holes in the poly tub
indicated by indents in bottom.
1/2" Flat Washer
1/2" Lock Washer
1/2" Hex Nut
MODEL #
UPC
DESCRIPTION:
MOTOALLIANCE - WWW.MOTOALLIANCE.COM - [phone]
Impact Trailer 100

11
16
3
4
2
1
15
11
7
14
8
14
13
12
10
17
Note: Prior to Final Assembly of Tub onto Frame
It will be required to drill (4) 9/16" dia. holes in the poly tub
indicated by indents in bottom.
See next page for
Tipper Latch Assembly Instructions
DETAIL I
SCALE 1 : 2
10
12
13
MODEL #
UPC
DESCRIPTION:
MOTOALLIANCE - WWW.MOTOALLIANCE.COM - [phone]
Impact Trailer 100

5
Note Direction of this plate during assembly.
4
3
1
2
8
7
6
Tipper Latch Assembly Instructions
5
Note Direction of this plate during assembly.
6
78
3 2
This End Secures
To Tow Vehicle
This End Secures
To Trailer Frame
ITEM
NO.
PART NUMBER Title QTY.
1 TL100 Latch Base Flange 1
2 TL101 Latch Trip Pin 1
3 TL102 Latch Spring 1
4 TL103 Latch Trip Handle 1
5 TL104 Latch Trip Plate 1
6 1/4-20x 1.25" Hex Bolt 1/4-20 x 1.25" Hex Bolt 1
7 Regular LW 0.25 1/4" Lock Washer 1
8 HNUT 0.2500-20-D-N 1/4-20 Hex Nut 1
MODEL #
UPC
DESCRIPTION:
MOTOALLIANCE - WWW.MOTOALLIANCE.COM - [phone]
Trip Latch Assembly

2
3
4
3
1
1/4-20 Hardware intentionaly used in
5/16-18 holes for proper alignment and fit during assembly
5
678
6
5
Note:
While assembling the rail kit, do not fully tighten
all hardware until the rail kit is installed onto the poly tub.
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 ITA503 Left Side Rail 1
2 ITA504 Right Side Rail 1
3 ITA200 Corner Brackets 2
4 ITA-308 Front Rail 1
5 IN-HHMS 0.25-20x1.75x1.75-N 1/4-20 x1.75" Hex Bolt 12
6 Regular FW 0.25 1/4" Flat Washer 24
7 Regular LW 0.25 1/4" Lock Washer 12
8 HNUT 0.2500-20-D-N 1/4-20 Hex Nut 12
MODEL #
UPC
DESCRIPTION:
MOTOALLIANCE - WWW.MOTOALLIANCE.COM - [phone]
Rail Extension Kit

U
V
Note:
Prior to Installation of Rail Kit onto tub, it will be required to drill (8) 3/8" dia. holes in tub.
Hole locations to be located at indents in the top surface of the Poly Tub.
Once holes have been drilled in plastic tub, and rail kit hardware is installed, then proceed to tighten all hardware.
Indent - 3/8" Hole Location 8x
DETAIL U
SCALE 1 : 6
6
4
5
3
4
Indent/Hole Location
DETAIL V
SCALE 1 : 6
4
56
3
Indent/Hole Location
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 ITA-300 Impact Trailer 100 1
2 ITA505 - Rail Extention Kit Rail Extension Kit 1
3 HBOLT 0.3125-18x1.75x0.875-N 5/16-18 Hex Bolt 8
4 Regular FW 0.3125 5/16-18 Flat Washer 10
5 Regular LW 0.3125 5/16-18 Lock Washer 8
6 HNUT 0.3125-18-D-N 5/16-18 Hex Nut 8
MODEL #
UPC
DESCRIPTION:
MOTOALLIANCE - WWW.MOTOALLIANCE.COM - [phone]
Impact Trailer 100 / Rail
Extention Components