Motolux 807110000 Installation manual
Australian owned
Australian designed
61 (0)3 9876 0400
www.motolux.com.au
Ordering Information
Australia / New Zealand
1 CHANNEL MOTOR CONTROLLER WITH BUILT IN RADIO RECIEVER – 807110000
Pairing A Multi-Channel Remote or Multiple Remotes
PROGRAMMING INSTRUCTIONS 1/3
*Please note that a maximum of 5 Remotes/Channels or Devices can only be paired to each single channel Motor Control Unit
Pairing the Motor controller to a Remote Control:
1. Make sure power is switched on to the motor controller.
2. Pressandholdthe‘Learn’buttonontopofthemotorcontrolboxfor1second,youwillbeabletoseeaslowashingRED
light behind the tinted screen.
3. Nowontheremotecontrol,makingsureyouareontherightchannel/remote,brieypresstheup button. The motor
controller will emit three BLUEashinglightstoindicatethatthechannel/remoteispaired.
To Change Direction of the Motor (Two Methods)
(First method):
1. On a channel that is paired to the remote, push and hold the Stop Button for three seconds. the RED light on controller will
startashingataslowsteadyrate.
2. NowpushtheDownButtonandtheandthelightinsidethecontrollerwillashBLUEthreetimestoconrmthatthe
direction is changed.
3. Test the motor.
(Second method):
1. Undo the screw at the bottom of the motor controller and slide the front cover off.
2. Towards the top of the circuit board, you will be able to see a dip switch. Flick the switch to either left or right to change the
motor direction.
3. Test the motor.
To Take the Motor Out of Venetian Blind Mode:
In case the Motor Controller is set to Venetian Blind Mode you will need to:
1. On a channel that is paired to the remote, push and hold the Stop Button for three seconds. the RED light on the controller
willstartashingataslowsteadyrate.
2. NowbrieypushtheStopButtonandtheandthelightinsidethecontrollerwillashBLUEthreetimestoconrmthatthe
motor has been taken out of venetian mode.
3. Test the motor.
To Delete a Single Channel or a Remote from the Motor Controller:
If by chance a remote or channel has been paired by mistake, follow these steps to remove it:
1. On the Motor Controller, push and hold the stop button on the remote. The REDlightoncontrollerwillstartashingata
slow steady rate.
2. Making sure that you have the remote on the correct channel to be deleted, push and hold setting button on the remote until you
see the BLUE lightintheMotorControllerashthreetimesconrmingthatyouhavedeletedthatchannelorremote.
3. Test the motor.
Motolux is a world-class manufacturer of motorisation products and systems dedicated to window covering markets
worldwide. A designer and manufacturer of a fully integrated range of motorisation solutions, Motolux products are
suitable for commercial or residential use. Our high quality product range is streamlined to simplify the process of
manufacturing, installation and ongoing maintenance of almost any type of motorised window covering product.
REVISION 1 - 2021
Australian owned
Australian designed
61 (0)3 9876 0400
www.motolux.com.au
Ordering Information
Australia / New Zealand
1 CHANNEL MOTOR CONTROLLER WITH BUILT IN RADIO RECIEVER – 807110000
Pairing A Multi-Channel Remote or Multiple Remotes cont.
PROGRAMMING INSTRUCTIONS 2/3
*Please note that a maximum of 5 Remotes/Channels or Devices can only be paired to each single channel Motor Control Unit
Motolux is a world-class manufacturer of motorisation products and systems dedicated to window covering markets
worldwide. A designer and manufacturer of a fully integrated range of motorisation solutions, Motolux products are
suitable for commercial or residential use. Our high quality product range is streamlined to simplify the process of
manufacturing, installation and ongoing maintenance of almost any type of motorised window covering product.
REVISION 1 - 2021
To Delete All Channels or Remotes from the Motor Controller (Two Methods)
(First method):
1. On any remote/channel paired, press the hold the stop button on the remote for 3 seconds. The REDlightwillstartashing
at a slow steady rate.
2. Now press and hold the button on the back of the remote for a total of 7 seconds. You will see a BLUElightashthreetimes,
thenwillashBLUE another three times to indicate all channels/remotes are now deleted from the motor controller.
(Second method):
1. On the Motor Controller, push and hold the Learn button on the top of the motor controller for 3 seconds, or until you see
the REDlightashingatafastrate.Letgoofthelearnbutton.
2. Nowbrieypressthelearnbuttonagain.theBLUEwilllightashthreetimesindicatingthatallchannels/remotesarenow
deleted from the motor controller.
Pairing the Motolux Wind/Sun Sensor to the Motor Controller:
1. On the Remote Control on each channel that you want to be controlled by the Wind Sensor, push and hold the learn button
for one second. The RED light inside the controller will start blinking at a slow steady rate.
2. On the Wind Sensor, Push and hold the “LEARN “Button and the light inside the controller will BLUEashthreetimesto
conrmthatWindSensorispairedtothatchannel.
Wind Settings
1= 10Kmh – 9 = 50Kmh
0 = Off
The Wind/Sun Sensors also have a light sensor that you can use to lower the blinds in direct sunlight, the settings are 1 – 9, if
you do not want to use this function please set the threshold to 0 this will turn the function off.
Australian owned
Australian designed
61 (0)3 9876 0400
www.motolux.com.au
Ordering Information
Australia / New Zealand
1 CHANNEL MOTOR CONTROLLER WITH BUILT IN RADIO RECIEVER –
807110000
PROGRAMMING INSTRUCTIONS 3/3
*Please note that a maximum of 5 Remotes/Channels or Devices can only be paired to each single channel Motor Control Unit
Motolux is a world-class manufacturer of motorisation products and systems dedicated to window covering markets
worldwide. A designer and manufacturer of a fully integrated range of motorisation solutions, Motolux products are
suitable for commercial or residential use. Our high quality product range is streamlined to simplify the process of
manufacturing, installation and ongoing maintenance of almost any type of motorised window covering product.
REVISION 1 - 2021
Controller Wiring Diagram Controller Diagram
AC Power Connection
Caution:
The working mode for external
manual switch is no power dry
contact mode, the function of
this two interface is the same.
Table of contents
