Motomaster Eliminator 011-1906-4 User manual

2

3
TABLE OF CONTENTS
Safety Information 4
10
12
16
18
19
20
Warranty Information
Jump Starting
User Interface
Errors
Charging
Operating Flashlight
Technical Specifications
21
22
Understanding Charge LEDs

4
WARNING
READ AND UNDERSTAND ALL SAFETY
INFORMATION BEFORE USING THIS
PRODUCT. Failure to follow these safety
instructions may cause an ELECTRICAL
SHOCK, EXPLOSION, FIRE, which may
result in a SERIOUS INJURY, DEATH, or
PROPERTY DAMAGE.
Electrical Shock. Product is an electrical
device that can shock and cause serious
injury. Do not cut power cords. Do not
submerge in water or get wet.
Explosion. Unmonitored, incompatible, or
damaged batteries can explode if used with
product. Do not leave product unattended
while in use. Do not attempt to jump start
a damaged or frozen battery. Use product
only with batteries of recommended voltage.
Operate product in well ventilated areas.
Fire. Product is an electrical device that
emits heat and is capable of causing burns.
Do not cover product. Do not smoke or
use anything that can cause an electrical
spark or fire when operating product. Keep
product away from combustible materials.
Eye Injury. Wear eye protection when
operating product. Batteries can explode
and cause flying debris. Battery acid can
cause eye and skin irritation. In the case of
contamination of eyes or skin, flush affected
area with running clean water and contact
poison control immediately.
Explosive Gases. Working in the vicinity
of a lead-acid is dangerous. Batteries
generate explosive gases during normal
battery operation. To reduce risk of battery
explosion, follow all safety information
instructions and those published by the
battery manufacturer and manufacturer
of any equipment intended to be used in
the vicinity of battery. Review cautionary
markings on these products and on engine.
SAFETY INFORMATION

5
SAFETY INFORMATION
Important Safety Warnings
•Proposition 65:Battery posts, terminals, and
related accessories contain chemicals, including lead.
These materials are known to the State of California to
cause cancer and birth defects and other reproductive
harm.
•Personal Precaution: Only use product as
intended. Someone should be within range of your
voice or close enough to come to your aid in case of
emergency. Have a supply of clean water and soap
nearby in the case of battery acid contamination. Wear
complete eye protection and protective clothing while
working near a battery. Always wash hands after handling
batteries and related materials. Do not handle or wear
any metal objects when working with batteries including;
tools, watches or jewelry. If metal is dropped onto battery,
it may spark or create a short circuit resulting in electrical
shock, fire, explosion which may result in injury, death or
property damage.
•Minors: If the product is intended by “Purchaser” to
be used by a minor, purchasing adult agrees to provide
detailed instructions and warnings to any minor prior
to use. Failure to do so is the sole responsibility of the
“Purchaser,” who agrees to indemnify MotoMaster®for
any unintended use or misuse by a minor.
•Choking Hazard: Accessories may present
a choking hazard to children. Do not leave children
unattended with product or any accessory. The product
is not a toy.
•Handling: Handle product with care. The product
can become damaged if impacted. Do not use a
damaged product, including, but not limited to, cracks to
the casing or damaged cables. Do not use product

6
SAFETY INFORMATION
model no. 011-1906-4 contact us 1.888.942.6686
with a damaged power cord. Humidity and liquids may
damage product. Do not handle product or any electrical
components near any liquid. Store and operate product in
dry locations. Do not operate product if it becomes wet. If
product is already operating and becomes wet, disconnect
it from the battery and discontinue use immediately. Do not
disconnect the product by pulling on the cables.
•Modifications: Do not attempt to alter, modify or
repair any part of the product. Disassembling product
may cause injury, death or damage to property. If product
becomes damaged, malfunctions or comes in contact with
any liquid, discontinue use, and contact MotoMaster®. Any
modifications to the product will void your warranty.
•Accessories: This product is only approved for
use with MotoMaster®accessories. MotoMaster®is
not responsible for user safety or damage when using
accessories not approved by MotoMaster®.
•Location: Prevent battery acid from coming in to
contact with the product. Do not operate the product in
a closed-in area or an area with restricted ventilation. Do
not set a battery on top of product. Position cable leads to
avoid accidental damage by moving vehicle parts (including
hoods and doors), moving engine parts (including fan
blades, belts, and pulleys), or what could become a hazard
that may cause injury or death.
•Operating Temperature: This product is designed
to work in ambient temperatures between -30 to 50º C.
Do not operate outside of temperature ranges. Do not
jump start a frozen battery. Discontinue use of product
immediately if the battery becomes excessively warm.
•Storage: Do not use or store your product in areas with
high concentrations of dust or airborne materials. Store
your product on flat secure surfaces so it’s not prone to
falling. Store your product in a dry location. The storage
temperature is -20 to 25ºC (average temperature). Never

7
SAFETY INFORMATION
model no. 011-1906-4 contact us 1.888.942.6686
exceed 80ºC under any condition.
•Compatibility: The product is only compatible with
12 V lead-acid batteries. Do not attempt to use product
with any other type of battery. Jump starting other
battery chemistries may result in injury, death or property
damage. Contact the battery manufacturer prior to
attempting to jump start the battery. Do not jump start a
battery if you are unsure of the battery’s specific chemistry
or voltage.
•The Battery: The built-in lithium-ion battery in the
product should be replaced only by MotoMaster®,
and must be recycled or disposed of separately from
household waste. Do not attempt to replace the battery
yourself and do not handle a damaged or leaking lithium-
ion battery. Never dispose of battery in household trash.
Disposal of batteries in household trash is unlawful under
state and federal environmental laws and regulations.
Always take used batteries to your local battery recycling
center. If the product battery is excessively hot, emitting
an odor, deformed, cut, is experiencing or demonstrating
an abnormal occurrence, immediately stop all use and
contact MotoMaster®.
•Battery Charging: Charge the product with the
included USB charge cable and a MotoMaster®10 W
12 V power adapter. A third-party USB cable and 5 W
or 10 W power adapter that are compatible with USB
2.0 or power adapters compliant with one or more of the
following standards EN 301489-34, IEC 62684, YD/T
1591-2009, CNS 15285, ITUL.1000 may be used. Be
cautious of using low quality power adaptors, as they may
present a serious electrical risk that can result in injury to
person, device, and property. If using a third party USB
power adapter, contact the manufacturer(s) to find out if
your power adapter complies with the above standards.
Using damaged cables or chargers, or charging when

8
SAFETY INFORMATION
model no. 011-1906-4 contact us 1.888.942.6686
model no. 011-1906-4 contact us 1.888.942.6686
moisture is present, can result in electric shock. Using generic
or third-party power adapter may shorten the life of your
product and cause the product to malfunction. MotoMaster®
is not responsible for the user’s safety when using accessories
or supplies that are not approved by MotoMaster®.
When using a USB Power Adapter to charge the product,
make sure that the AC plug is fully inserted into the adapter
before you plug it into a power outlet. Power adapters may
become warm during normal use, and prolonged skin contact
may cause bodily injury. Always allow adequate ventilation
around power adapters when using them.
To ensure maximum battery life, avoid charging your product
for more than a week at a time, as overcharging may shorten
battery life. Over time, an unused product will discharge and
must be recharged before use. Disconnect the product from
power sources when not in use. Use the product only for their
intended purposes.
•Medical Devices: Product may emit electromagnetic
fields. Product contains magnetic components which may
interfere with pacemakers, defibrilators, or other medical
devices. Consult with your physician prior to use if you have
any medical device including pacemakers. If you suspect the
product is interfering with a medical device, stop using the
product immediately and consult your physician.
•Medical Conditions: If you have any medical condition
that you believe could be affected by product, including but
not limited to; seizures, blackouts, eyestrain or headaches,
consult your physician prior to use of product. The use of an
integrated high-powered flashlight contains a light sensitivity
hazard. Use of the light in Strobe Mode may cause seizures
in persons with photosensitive epilepsy, which may result in
serious injury or death.

9
SAFETY INFORMATION
model no. 011-1906-4 contact us 1.888.942.6686
•Light: Staring directly into the light beam of the
flashlight may result in permanent eye injury. The product
is equipped with a high output LED pre-focused lamp that
emits a powerful beam at the highest setting.
•Cleaning: Power off the product before attempting
any maintenance or cleaning. Clean and dry product
immediately if it comes in contact with liquid or any type of
contaminant. Use a soft, lint-free (microfiber) cloth. Avoid
getting moisture in openings.
•Explosive Atmospheres: Obey all signs and
instructions. Do not operate product in any area with a
potentially explosive atmosphere, including fueling areas
or areas which contain chemicals or particles such as
grain, dust or metal powders.
•High-Consequence Activities: This product is
not intended for use where the failure of the product could
lead to injury, death or severe environmental damage.
•Radio Frequency Interference: Product
is designed, tested, and manufactured to comply with
regulations governing radio frequency emissions. Such
emissions from the product can negatively affect the
operation of other electronic equipment, causing them to
malfunction.
•MotoMaster®FCC Compliance
This device complies with Part 15 (Radio Frequency
Devices) of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference when the equipment is operated

10
WARRANTY INFORMATION
model no. 011-1906-4 contact us 1.888.942.6686
in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
•MotoMaster®1 Year Limited Warranty:
MotoMaster®warrants that its products (the “Product”) will be
free from defects in material and workmanship for a period of
one (1) year from the date of purchase (the “Warranty Period”).
For defects reported during the Warranty Period, MotoMaster®
will, at its discretion, and subject to MotoMaster®’s technical
support analysis, either repair or replace, for the fees set
forth below. Replacement parts and products will be new or
serviceably used, comparable in function and performance
to the original part and warranted for the remainder of the
original Warranty Period.
THE FOREGOING LIMITED WARRANTY IS IN LIEU OF AND
EXCLUDES ALL OTHER WARRANTIES NOT EXPRESSLY
SET FORTH HEREIN, WHETHER EXPRESS OR IMPLIED
BY OPERATION OF LAW OR OTHERWISE, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
MOTOMASTER®’S LIABILITY UNDER THIS LIMITED
WARRANTY IS EXPRESSLY LIMITED TO REPLACEMENT
(IN THE FORM AND UNDER THE TERMS ORIGINALLY
SHIPPED), OR TO REPAIR, WHETHER SUCH CLAIMS ARE
FOR BREACH OF WARRANTY OR FOR NEGLIGENCE.
MOTOMASTER®SHALL NOT BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL, OR SPECIAL LOSSES,
DAMAGES OR EXPENSES OF ANY KIND, INCLUDING,
WITHOUT LIMITATION, ANY SUCH LOSSES, DAMAGES, OR
EXPENSES ARISING DIRECTLY OR INDIRECTLY FROM THE
SALE, HANDLING, OR USE OF THE PRODUCT FROM ANY
OTHER CAUSE RELATING THERETO, OR FROM PERSONAL
INJURY OR LOSS OF PROFIT.

11
WARRANTY INFORMATION
model no. 011-1906-4 contact us 1.888.942.6686
Some states, provinces and countries do NOT allow the
exclusion or limitation of incidental or consequential damages
or length of an implied warranty so the above limitation(s) or
exclusion(s) may NOT apply. This Limited Warranty gives you
specific legal rights and you may also have other legal rights,
which vary by state, province and country.
•Limited Warranty.
This Limited Warranty is made to the original purchaser from
MotoMaster®and does NOT extend to any other person or
entity and is NOT assignable. It is the obligation of the original
purchaser to:
1.) Return merchandise to a Canadian Tire location with receipt.
THIS LIMITED WARRANTY IS VOID UNDER THE FOLLOWING
CONDITIONS:
1.) The Product is misused, subjected to careless handling, or
operated under conditions of extreme temperature, shock, or
vibration beyond MotoMaster®’s recommendations for safe and
effective use.
2.) The Product has NOT been installed, operated, or maintained in
accordance with approved procedures.
3.) The Product is disassembled, altered, or repaired by anyone,
except MotoMaster®.
4.) The electrical connections to the DC output of the product are
modified without the express written consent of MotoMaster®.
5.) The Product is subject to improper storage or accident.
THIS LIMITED WARRANTY DOES NOT COVER:
1.) Normal wear and tear.
2.) Cosmetic damage that does NOT affect functionality.
3.) Products where the MotoMaster® serial number is missing,
altered, or defaced.

12
JUMP STARTING
model no. 011-1906-4 contact us 1.888.942.6686
•About Jump Starter: The MotoMaster®jump starter
is a compact and portable lithium-ion jump starter for cars,
boats, motorcycles, ATVs, lawn mowers, RVs, tractors,
trucks and more. It’s extremely safe for anyone to use.
It features spark proof technology and reverse polarity
protection. The MotoMaster®jump starter can instantly
jump start most single-battery applications, up to 20 times
on a single charge. The MotoMaster®jump starter is also
equipped with a USB battery pack and LED flashlight,
making it the ultimate emergency tool.
•Getting Started: The jump starter comes partially
charged out of the box and needs to be fully charged
prior to use. Carefully read and understand the vehicle
owner’s manual on specific precautions and recommended
methods for jump starting the vehicle. Make sure to
determine the voltage and chemistry of the battery by
referring to your battery owner’s manual prior to using this
product. The MotoMaster®jump starter is for jump starting
12 V lead-acid batteries only.
•Connecting to the Battery:
Before connecting to the battery, verify that you have a
12 V lead-acid battery. The jump starter is not suitable for
any other type of battery. Identify the correct polarity of
the battery terminals on the battery. The positive battery
terminal is typically marked by these letters or symbol (POS,
P, +). The negative battery terminal is typically marked
by these letters or symbol (NEG, N, -). Do not make any
connections to the carburetor, fuel lines, or thin sheet metal
parts. The instructions below are for a negative ground
system (most common). If your vehicle is a positive ground
system (very uncommon), follow the instructions below in
reverse order.
1.) Connect the positive (red) HD battery clamp to the
positive (POS, P, +) battery terminal.
2.) Connect the negative (black) HD battery clamp to the
negative (NEG, N, -) battery terminal or vehicle chassis.

13
JUMP STARTING
model no. 011-1906-4 contact us 1.888.942.6686
3.) When disconnecting, disconnect in the reverse
sequence, removing the negative first (or positive first for
positive ground systems).
•Jump Starting:
1.) Verify the voltage and chemistry of the battery.
2.) Confirm the battery clamps are connected to the
correct polarity battery terminals.
3.) Connect the clamps to the jump starter.
4.) Make sure all of the vehicle’s power loads (headlights,
radio, air conditioning, etc.) are turned off before
attempting to jump start the vehicle.
5.) Press the Power Button to begin jump starting. All
LEDs will flash, indicating that all LEDs are properly
functioning. If you are properly connected to the battery,
the White LED will illuminate. If the battery clamps are
connected in reverse, the Red Error LED will illuminate.
Reverse the connections to clear this error and then the
White LED will illuminate. The White LED is illuminated
when the jump starter is ready to jump start your vehicle.
6.) Try starting the vehicle. Most vehicles will immediately
start. Some vehicles may require the jump starter to
be connected for up to 30 seconds before starting.
If the vehicle does not start right away, wait 20-30
seconds and try again. Do not attempt more than five
(5) consecutive jump starts within a fifteen (15) minute
period. Allow the jump starter to rest for fifteen (15)
minutes before attempting to jump start the vehicle again.
7.) Once you have started your vehicle, disconnect the
battery clamps, and remove the jump starter.

14
JUMP STARTING
model no. 011-1906-4 contact us 1.888.942.6686
•Low Voltage Batteries & Manual Override:
The jump starter is designed to jump start 12 V lead-acid
batteries down to 2 V. If your battery is below 2 V, the White
LED will be “Off”. This is an indication that the jump starter
cannot detect a battery.
If you need to jump start a battery below 2 V there is a
Manual Override feature, which allows you to force “On” the
jump start function.
CAUTION: USE THIS MODE WITH EXTREME CARE.
THIS MODE IS FOR 12 V LEAD-ACID BATTERIES ONLY.
BOTH THE SPARK PROOF AND REVERSE POLARITY
PROTECTION FEATURES ARE DISABLED. PAY VERY
CLOSE ATTENTION TO THE POLARITY OF THE BATTERY
BEFORE USING THIS MODE. DO NOT ALLOW THE
POSITIVE AND NEGATIVE BATTERY CLAMPS TO TOUCH
OR CONNECT TO EACH OTHER AS THE PRODUCT WILL
GENERATE SPARKS. THIS MODE USES VERY HIGH
CURRENT (UP TO 1000 A) THAT CAN CAUSE SPARKS
AND HIGH HEAT IF NOT USED PROPERLY. IF YOU ARE
UNSURE ABOUT USING THIS MODE, DO NOT ATTEMPT
AND SEEK PROFESSIONAL HELP.
Before using the Manual Override feature, make sure the
battery clamps are connected to the correct polarity battery
terminals and the connector is connected to the jump
starter. To use the Manual Override feature, press and hold
the Manual Override Button (a red exclamation point icon
inside a red circle) for three (3) seconds. The White LED
will flash “On” and “Off” indicating you have successfully
entered into Manual Override and it is ready to jump start
your vehicle. If connected in reverse polarity, the Red Error
LED will illuminate and the unit will not operate.
CAUTION: POWER THE JUMP STARTER “OFF” BEFORE
DISCONNECTING THE BATTERY CLAMPS. THIS WILL
ENSURE YOUR SAFETY. REMEMBER BOTH THE
SPARK PROOF AND REVERSE POLARITY PROTECTION
FEATURES ARE DISABLED.

15
model no. 011-1906-4 contact us 1.888.942.6686
Most vehicles will immediately start. Some vehicles
may require the jump starter to be connected for up
to 30 seconds before starting. If the vehicle does not
start right away, wait 20-30 seconds and try again. Do
not attempt more than five (5) consecutive jump starts
within a fifteen (15) minute period. Allow the jump
starter to rest for fifteen (15) minutes before attempting
to jump start the vehicle again.
JUMP STARTING

16
7
6
5
1
2
3
4
USER INTERFACE
model no. 011-1906-4 contact us 1.888.942.6686
®

17
User Interface.
1. Internal Battery Level
Indicates the charge level of the internal battery.
2. Error LED
Illuminates Red if reverse polarity is detected, or blinks
“On” and “Off” when the internal battery temperature is
too high.
3. Power Button
Push to turn unit “On” & “Off”.
4. Power LED
Illunimates White when unit is “On”.
5. Jump Starting LED
Illuminates White when the jump starter is active. If the unit
is connected properly to a battery, the jump starter will
automatically detect a battery and go into jump starting
mode (LED flashes White when Manual Overide feature is
active).
6. Manual Override Button
To enable, push and hold for three (3) seconds.
WARNING: Disables safety protection and manually
forces the jump starter “On”. Only for use when a
battery is too low to be detected.
7. Light Mode Button
Toggles the ultra-bright LED light through 7 light modes:
100% > 50% > 10% > SOS > Blink > Strobe > Off
USER INTERFACE
model no. 011-1906-4 contact us 1.888.942.6686

18
UNDERSTANDING LEDS
LED Explanation
25%
Red LED The 25% Charge LED will ‘breathe’
on/off while charging and will be solid
Red when the internal battery is 25%
charged.
50%
Red LED
75%
Yellow LED
The 50% Charge LED will ‘breathe’
on/off while charging and will be solid
Red when the internal battery is 50%
charged.
The 75% Charge LED will ‘breathe’
on/off while charging and will be solid
Yellow when the internal battery is
75% charged.
The 100% Charge LED will ‘breathe’
on/off while charging and will be solid
Green when the internal battery is fully
charged.
When connected to a USB charger,
no other charge LEDs will be
illuminated. Once disconnected from
the charger, all four (4) Charge LEDs
will be illuminated when the internal
battery is between 75%-100%, and
the unit is powered “ON”.
100%
Green LED
25% 50% 75% 100%
25% 50% 75% 100%
25% 50% 75% 100%
25% 50% 75% 100%
model no. 011-1906-4 contact us 1.888.942.6686
•Understanding Charge LEDs:
The jump starter has four (4) Charge LEDs - 25%, 50%,
75% and 100%. These charge LEDs indicate the internal
battery’s state-of-charge (SOC). See below:

19
Error LED
Solid Red
Reverse polarity/
Reverse the battery
connections.
Error Reason/Solution
Error LED
Blinking Red
w/Cables Connected
Properly
The internal battery is too
hot/
Allow the unit to cool.
Bring the unit into cooler
environment.
Boost Light Does
Not Come On
w/Cables Connected
Properly
Connected battery is below
2 V/
Remove all loads, and
try again, or use Manual
Override Mode.
ERRORS
model no. 011-1906-4 contact us 1.888.942.6686
•Understanding Error Conditions:
The jump starter shall display an Error Condition when a
reverse polarity condition is present, a battery below two
(2) volts, or the internal battery overheating. When one
of these Error Conditions are present, the following will
happen:
•Charging the Jump Starter:
Connect the jump starter using the included USB charge
cable to the USB IN port. It can be recharged from any
USB powered port, like an AC adapter, car charger,
laptop and more. The USB IN port is rated at 2.1 Amps
to ensure safe and efficient charging of the internal lithium
battery. Due to FCC regulations, we recommend not to
charge and discharge the unit at the same time.

20
CHARGING
Time
USB Charger Rating
12hr
.5A
6hr
1A
3hr
2A
model no. 011-1906-4 contact us 1.888.942.6686
Charging Times:
The time to recharge the jump starter will differ based on
the discharge level and the power source used. Actual
results may vary due to battery conditions.
Charging Your USB Devices:
You can recharge virtually any USB device, such as a
smartphone. Connect the included USB Charge Cable to
the USB OUT port and connect to your USB device.
The number of times you can recharge a USB device will
vary between devices. For recharge times, contact your
device manufacturer.