Motorline professional M CELE 01 Use and care manual

1 2
43
FUNC
1
2 4
8
9
10
7
5
63
987654321
EN
LED Exit Only
Always Closed RESET Button
Partial Opening (Automatic Functioning) Wall fixation
Always Open Connector
Total Opening (Automatic Functioning)  Box screw
Nº WIRE COLOR INPUT DESCRIPTION
1Grey PED Partial opening contact
2Brown PED Partial opening contact
3Orange COM Opening dry contact
4Purple PUL Opening dry contact
5Blue SIG Electric lock signal
6Green RIN Internal sensor signal
7White REX External sensor signal
*Yellow ACESS Not used
8Black GND (GND)
9Red V 12V~36V DC Power Supply
TECHNICAL SPECIFICATIONS CONNECTIONS DIAGRAM
• SELECTOR DESCRIPTION
The "M CELE 01" selector has 5 operating modes: Total Opening, Total Closing,
Partial Opening, Exit Only and Automatic Mode. These modes can be operated
with or without a security password. This switch contains a LED (light effect)
and a buzzer (sound effect) to assist the programming procedure. It is powered
by 15VDC directly from the door's automatism. It contains memory in case of
power failure.
M CELE 01 Selector|
USER'S AND INSTALLER'S
MANUAL
RECEIVER INSTALLATION
. Mark the holder
mounting points and
drill the holes.
. Point the holder and
insert the dowels and
screws.
. Pass the wire and
fit the connector on the
selector.
. Place the selector on
the support. Leave the
cable stretched.

1
3
4
2
1
3
4
2
1
3
4
2
1
3
4
2
1
3
4
2
1
3
4
2
1
3
4
2
1
3
4
2
1
3
4
2
1
3
4
2
1
3
4
2
1
3
4
2
1 2
43
FUNC
EN
SELECTOR PROGRAMMING SELECTOR PROGRAMMING
• FUNCTIONS
• PROGRAMMING
You can use the selector in two modes: Code and Free. In "code" it is necessary to put a
combination of four numbers (original code is ) to change the operating function.
Press and hold the FUNC button   key (LOCK) for  sec. The selector
will beep and the light changes from red (Code mode) to green, indi-
cating that it is in free mode. Repeat the procedure to switch to code
mode.
Change the selector's function in "Code Mode":
Change the selector's function in "Free Mode":
Changing from "Code Mode" to "Free Mode":
01 • Press and hold the
FUNC button for 5 sec.
The selector will beep
and the LED turns
green.
In "free" mode, you can select the desired function by pressing it for
sec, without having to put the password.
02 • Enter the code
(original - 1234). 03 • Press the FUNC button to confirm. 04 • Choose one of the functions described
above by pressing the
key corresponding to
the function.
In case of forgetting your password, follow the next steps:
Reset the Selector:
01 • Press and hold the
FUNC button for 10 sec.
The selector will beep
twice. First at 5 sec
and then at 10 sec.
01 • Unscrew the
screw cover (below the
switch) and remove
the rear panel.
03 • The selector beeps once confirming the reset's success. The password returns to 1234. Refit
the back cover and tighten the screw.
02 • With the selector
on, press the RESET
button on the board
for 40sec.
02 • Enter the code
(original - 1234). 03 • Press the FUNC button to confirm.
05 • Press the FUNC
button to confirm. 07 • Press the FUNC button to confirm
again. The new
password is now set.
04 • Enter a new code.
06 • Enter for a second
time the new code.
Always Closed
• All radars and controllers are disabled.The lock is automatically triggered,which causes the door to
close.If you connect a fire alarm and put the door in this function, the door will not open if it receives
an alarm order.
Always Open
• All radars and controllers are disabled.The door stays open.
Partial Opening (Automatic Operation)
• The radars are activated. The door opens only partially (65% of total course) automatically. Whenever
activated this function, the door does a new path recognition.
Exit Only
• The external radar is disabled and the lock is activated automatically. The controllers and inner radar
stay activated. Only opens for exiting people.
Total Opening (Automatic Operation)
• All radars and controllers are activated. The door opens and closes automatically.
M CELE 01 Selector|
USER'S AND INSTALLER'S
MANUAL
Change Password: