Motorola DLR SERIES User manual

DLR SERIES
DIGITAL
MADE EASY
QUICK REFERENCE GUIDE FOR RADIO FEATURES BarCodeDirect.com

DLR SERIES
QUICK REFERENCE GUIDE
MODELS:
DLR 1020 – 2 channels
DLR 1060 – 6 channels
Frequency band: ISM 900 MHz
1. Radio Overview
2. Battery – Insert and Charge
3. Basic Operations
4. AdvancedConguration
5. Special Call Features
6. CPS Software
7. Troubleshooting and FAQ
TABLE OF CONTENTS
BarCodeDirect.com

DLR 1020/1060
RADIO OVERVIEW
Audio
accessory
connector
Top Button
Antenna
Tx/Rx
Indicator
LED
PPT Button
Speaker
Audio
accessory
connector
Battery
Volume/ Up-Down
Control Buttons
Power Buttons
Channel/
Menu Button
Holster
BarCodeDirect.com

DLR 1020/1060
BATTERY – INSERTING
To insert or remove the battery, set the latch in the
“unlocked“ position, and open the battery door.
Remember to always set the latch back to the
“locked” position in order to prevent battery
from falling out by accident.
Unlocked/Locked latch
Battery
door
BarCodeDirect.com

DLR 1020/1060
RADIO OVERVIEW
To charge a battery, insert the radio or a stand-alone
battery into the single or multiple unit charger. The light
on the charger is red when the radio is charging. It turns
to green once the radio is fully charged.
LED turns green
battery is fully charged
Multiple-unit charger
Single-unit charger
stand-alone battery Holster
BarCodeDirect.com

DLR 1020/1060
Basic Operations
TALK
PTT (Push To Talk) Button – push
rmly,waitfortheTPT(TalkPermit
Tone), speak into the mic
(5 inches away from mouth)
PRIVATE REPLY
Press Top Button to queue up
for Private Reply* (while someone
is speaking to your channel),
then push PTT to call the last
person speaking. mouth)
ON/OFF
Power Button – long press to turn the
device ON/OFF, short press to check
battery status.
VOLUME
[+] / [-] buttons – press to adjust
volume
CHANNELS
Channel/Menu Button – press to
check the current channel. You can
now use [+] and [-] buttons to switch
channels. Press PTT to exit channel
browsing.
BarCodeDirect.com

DLR 1020/1060
AdvancedConguration
TheDLRAdvancedMenuModeallowsyoutocongurespecialsettingsinyourradiowithouttheneedprogramming
cables or additional software.
Max Channels
ProleID#
Top Button
MIC Gain
Home Channel
Choose a 4-digit number (0000 to 9999).
Customize it to ensure interference free/private communications.
Choose the max. number of channels you want to allow for your radio.
Set your Top button with one feature: Private Reply, Direct Call (only if enabled via CPS),
Call All Available, Page All Available, Mute, Disabled.
Choose High, Medium or Low to adjust the radio microphone sensitivity level
totdifferentusersand/ornoiseenvironments.
Choose the channel you want to designate as your main channel: the radio will return
to this channel in any case of longer inactivity.
BarCodeDirect.com

DLR 1020/1060
ADVANCED CONFIGURATION MENU
Entering Advanced Menu
To enter the Advanced Menu,
push Power Button together with PTT and [+].
PTT (Push-to-Talk) Button
[+] Button
Power Button
Channel/Menu Button – press to check
the current channel. You can now use
[+] and [-] buttons to switch channels.
Press PTT to exit channel browsing.
BarCodeDirect.com

DLR 1020/1060
ADVANCED CONFIGURATION MENU
Browsing Advanced Menu Options
Press Channel/Menu button to cycle
through the Advanced Menu options.
Voice prompt
“Programming Mode,
Press Menu to continue.”
Long press PTT to
exit Advanced
Menu Mode.
Home Channel
ProleID
Number
Max Channel
Top ButtonMic Gain
BarCodeDirect.com

DLR 1020/1060
ADVANCED CONFIGURATION MENU
1.ProleIDNumber–currentvalue
The radio announces the current PROFILE ID
number and prompts you to change it:
Press [+] or [-] to enter
theProleIDnumber
Sub-Menu. Press Channel/Menu button
to proceed to next
Advanced Menu option.
ATTENTION:DefaultProleIDnumberis“0000”!Makesuretochangeittoavoidinterferences
and ensure privacy.
Current Prole ID: <Digit1,
Digit2, Digit3, Digit4>; to
change, press [+] or [-]”
Long press PTT to
exit Advanced
Menu Mode.
Home Channel
ProleID
Number
Max Channel
Top ButtonMic Gain
BarCodeDirect.com

DLR 1020/1060
ADVANCED CONFIGURATION MENU
1.ProleIDNumber–changingvalues
The radio announces the current PROFILE ID
As you press the [+] or [-], the radio will announce
therstdigitvalueandpromptyoutochangeit:
Press [+] or [-] to enter
tochangetherst
ProleIDdigit. Press Channel/Menu button
to continue to the next digit.
ATTENTION:DefaultProleIDnumberis“0000”!Makesuretochangeittoavoidinterferences
and ensure privacy.
“First digit <number>.To
change, press [+] or [-].”
Long press PTT to
exit Advanced
Menu Mode.
Home Channel
ProleID
Number
Max Channel
Top ButtonMic Gain
BarCodeDirect.com

DLR 1020/1060
ADVANCED CONFIGURATION MENU
1.ProleIDNumber–sub-menu
As you press [+] or [-] to change the current digit,
radio will announce the values.
OnceyousetthelastdigitoftheProleIDNumberwiththeChannel/
Menu button, you will proceed to the next Advanced Menu option.
Press Channel/Menu button
to set digit and proceed to the next one.
Note: You can move forward through the 4 digits, but not backwards.
“zero, one, two, (…),
nine, zero…”
Long press PTT
to exit Advanced
Menu Mode.
DIGIT 4DIGIT 3DIGIT 2DIGIT 1
BarCodeDirect.com

DLR 1020/1060
ADVANCED CONFIGURATION MENU
1.ProleIDNumber–modicationconrmation
Onceyou’vedonesettingthe4-digitsprolenumber,
 theradiowillconrmthenewProleIDvalue.
Press Channel/Menu button
o proceed to the next
Advanced Menu option.
Note: If you realize the number set is not the one you want, press the Menu/Channel button and go
throughtheAdvancedMenuoptionsuntilyou’rebackonthebeginningoftheProleIDoptionand
repeat the steps. .
“Prole ID saved as:
<digit1, digit2, digit3,
igit4>. Press Menu to
continue.”
Long press PTT to
exit Advanced
Menu Mode.
Home Channel
ProleID
Number
Max Channel
Top ButtonMic Gain
BarCodeDirect.com

DLR 1020/1060
ADVANCED CONFIGURATION MENU
2. Maximum Channels
The radio announces the current maximum number of
channels and prompts you to change it:
Note: The maximum number of channels you can set up depends on
the radio model: DLR1060 – 6 channels; DLR1020 – 2 channels.
Press Channel/Menu button
to proceed to the next
Advanced Menu option.
“Max Channels
<number>. To change,
press [+] or [-].”
Long press PTT to
exit Advanced
Menu Mode.
Home Channel
ProleID
Number
Max Channel
Top ButtonMic Gain
Press [+] or [-] to enter
to change the number of
channels.
BarCodeDirect.com

DLR 1020/1060
ADVANCED CONFIGURATION MENU
3. Top Button – current feature
The radio announces the current Top Button feature and
prompts you to change it:
Note: The default function of Top Button is “Private Reply”.
Press Channel/Menu button
to proceed to the next Advanced
Menu option.
“Programmable Button
<Top Button Feature>. To
change, press [+] or [-].”
Long press PTT to
exit Advanced
Menu Mode.
Home Channel
ProleID
Number
Max Channel
Top ButtonMic Gain
Press [+] or [-] to change
the Top Button feature.
Top Button
BarCodeDirect.com

DLR 1020/1060
ADVANCED CONFIGURATION MENU
3. Top Button – sub-menu options
Use [+] / [-] buttons to browse the Top Button functions –
you will hear their names read.
Note:InordertousetheDirectCalloption,youmustrstsetitupusingCPSsoftware–otherwise,
the top button will respond with a “bonk” sound.
Press Channel/Menu button
to proceed to the next Advanced
Menu option.
“<Top feature>”
Long press PTT to
exit Advanced
Menu Mode.
Disabled
Private Reply
Direct Call
Top Button
Page All
Availble
Mute
Call All
Available
Press [+] or [-] to change
the Top Button feature.
Top Button
BarCodeDirect.com

DLR 1020/1060
ADVANCED CONFIGURATION MENU
4. MIC Gain
The radio announces the current MIC Gain setting and
prompts you to change it:
Note: You can switch between Low/Medium/High gain settings. The default value is “Medium”.
Press Channel/Menu button
to proceed to the next
Advanced Menu option.
“MIC Gain <MIC gain
level>. To change, press
plus or minus.”
Long press PTT to
exit Advanced
Menu Mode.
Home Channel
ProleID
Number
Max Channel
Top ButtonMic Gain
Press [+] or [-]
to change the
MIC Gain level.
BarCodeDirect.com

DLR 1020/1060
ADVANCED CONFIGURATION MENU
5. Home Channel
The radio announces the current Home Channel setting
and prompts you to change it:
Note:Theoptionstochoosefromare“Disabled”or“Channel#”(orchannelname,incaseithas
been set up via CPS). The default setting is “Disabled”.
Press Channel/Menu button
to proceed to the next
Advanced Menu option.
“Home Channel <Home
channel setting> to
change press [+] or [-].”
Long press PTT to
exit Advanced
Menu Mode.
Home Channel
ProleID
Number
Max Channel
Top ButtonMic Gain
Press [+] or [-]
to change the
Home Channel setting.
BarCodeDirect.com

SPECIAL
CALL FEATURE
BarCodeDirect.com

DLR 1020/1060
SPECIAL CALL FEATURES
Asmentionedbefore,theTopButtoncanbeconguredtoservedifferentfunctions:
Special Call Features:
>Private Reply
>Direct Call
>Page All Available
>Call All Available
Mute: instant mute function
Disabled: disables the Top Button
*Except for Private Reply and Mute,
you can also assign special call
features to a designated channel
instead of theTop Button.
Note: Private Reply is the default Top Button function. Go to Advanced Functions Menu to learn how to change it.
**TosetupDirectCallfunctionforthersttime(TopButtonorspecicchannel)youwillneedtousetheCPS.
Disabled
Private Reply
Direct Call
Top Button
Page All
Availble
Mute
Call All
Available
BarCodeDirect.com