Motorola Mg160 series User manual

MG160 Serie

KEM-ML37104-01B

Safety and General Information

Important Information on Safe and Efficient Operation

Read This Information Before Using Your Radio.

The information provided in this document supersedes the general

safety information in user guides published prior to December 1, 2002.

ransmit and Receive Procedure

Your two-way radio contains a transmitter and a receiver. To control

your exposure and ensure compliance with the general population/

uncontrolled environment exposure limits, always adhere to the

following procedure:

• Transmit no more than 50% of the time.

• To receive calls, release the PTT button.

• To transmit (talk), press the Push to Talk (PTT) button.

Transmitting 50% of the time, or less, is important because the radio

generates measurable RF energy exposure only when transmitting

(in terms of measuring standards compliance).

Exposure to Radio Frequency Energy

Your Motorola two-way radio complies with the following RF energy

exposure standards and guidelines:

• United States Federal Communications Commission, Code of

Federal Regulations; 47CFR part 2 sub-part J.

• American National Standards Institute (ANSI)/Institute of

Electrical and Electronic Engineers (IEEE) C95. 1-1992.

• Institute of Electrical and Electronics Engineers (IEEE) C95.

1-1999 Edition.

• International Commission on Non-Ionizing Radiation Protection

(ICNIRP) 1998.

• Ministry of ealth (Canada) Safety Code 6. Limits of uman

Exposure to Radiofrequency Electromagnetic Fields in the

Frequency Range from 3 K z to 300 G z, 1999.

• Australian Communications Authority Radiocommunications

(Electromagnetic Radiation— uman Exposure) Standard, 2003.

• ANATEL ANNEX to Resolution No. 303 of July 2, 2002.

• ANATEL ANNEX to Resolution No. 533 of September 10, 2009.

To ensure optimal radio performance and make sure human

exposure to radio frequency electromagnetic energy is within the

guidelines set forth in the above standards, always adhere to the

following procedures.

Portable Radio Operation and EME Exposure

Antenna Care

Use only the supplied or an approved replacement antenna.

Unauthorized antennas, modifications, or attachments could

damage the radio and may violate FCC regulations.

Do NOT hold the antenna when the radio is “IN USE.” olding the

antenna affects its effective range.

Bo y-Worn Operation

To maintain compliances with FCC/ ealth Canada RF exposure

guidelines if you wear a radio on your body when transmitting

always place the radio in a Motorola-supplied or approved clip

holder, holster, case or body harness for this product. Use of

non-Motorola-approved accessories may exceed FCC/ ealth

Canada RF exposure guidelines.

If you do not use one of the Motorola-supplied or approved

body-worn accessories and are not using the radio held in the

normal use position, ensure the radio and its antenna are at least 1

inch (2.5 cm) from your body when transmitting.

Data Operation

If applicable, when using any data feature of the radio with or

without an accessory cable, position the radio and its antenna at

least one inch (2.5 cm) from the body.

Approve Accessories

For a list of approved Motorola accessories, visit our Web site at

www.motorolasolutions.com/talkabout.

Electromagnetic Interference/Compatibility

Note: Nearly every electronic device is susceptible to

electromagnetic interference (EMI) if inadequately shielded,

designed or otherwise configured for electromagnetic compatibility.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference; and

2. This device must accept any interference received, including

interference that may cause undesired operation.

Facilities

To avoid electromagnetic interference and/or compatibility conflicts,

turn off your radio in any facility where posted notices instruct you

to do so. ospitals or health care facilities may be using equipment

that is sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your radio when onboard an

aircraft. Any use of a radio must be in accordance with applicable

regulations per airline crew instructions.

Me ical Devices – Pacemakers

The Advanced Medical Technology Association recommends that a

minimum separation of 6 inches (15 cm) be maintained between a

handheld wireless radio and a pacemaker. These recommendations

are consistent with the independent research by and

recommendations of the U.S. Food and Drug Administration.

People with pacemakers should:

• ALWAYS keep the radio more than 6 inches (15 cm) from their

pacemaker when the radio is turned ON.

• Not carry the radio in the breast pocket.

• Use the ear opposite the pacemaker to minimize the potential for

interference.

• Turn the radio OFF immediately if there is any reason to suspect

that interference is taking place.

Me ical Devices – Hearing Ai s

Some digital wireless radios may interfere with some hearing aids.

In the event of such interference, you may want to consult your

hearing aid manufacturer to discuss alternatives.

Me ical Devices – Other

If you use any other personal medical device, consult the

manufacturer of your device to determine if it is adequately shielded

from RF energy. Your physician may be able to assist you in

obtaining this information.

Safety and General Use While Driving

Check the laws and regulations regarding the use of radios in the

area where you drive, and always obey them. If you do use your

radio while driving, please:

• Give full attention to driving and to the road.

• Use hands-free operation, if available.

• Pull off the road and park before making or answering a call if

driving conditions so require.

The use of a two-way radio while engaged in activities requiring

concentration may cause distraction or otherwise impair your ability

to safely participate in such activities. Always use technology safely.

For More Information

For further information, you may call Motorola at 1-800-638-5119

(U.S.), or e-mail us at [email protected] or visit us on the

Internet at www.motorolasolutions.com/talkabout.

Do not place a portable radio in the area over an air bag or in the air

bag deployment area. Air bags inflate with great force. If a portable

radio is placed in the air bag deployment area and the air bag

inflates, the radio may be propelled with great force and cause

serious injury to occupants of the vehicle.

Potentially Explosive Atmospheres

Turn off your radio prior to entering any area with a potentially

explosive atmosphere. Only radio types that are especially qualified

should be used in such areas as “Intrinsically Safe.” Do not remove,

install or charge batteries in such areas. Sparks in a potentially

explosive atmosphere can cause an explosion or fire resulting in

bodily injury or even death.

Note: The areas with potentially explosive atmospheres referred to

above include fueling areas such as below decks on boats, fuel or

chemical transfer or storage facilities, areas where the air contains

chemicals or particles (such as grain, dust or metal powders) and

any other area where you would normally be advised to turn off your

vehicle engine. Areas with potentially explosive atmospheres are

often—but not always—posted.

Blasting Caps an Areas

To avoid possible interference with blasting operations, turn off your

radio when you are near electrical blasting caps, in a blasting area,

or in areas posted “Turn off two-way radios.” Obey all signs and

instructions.

Operational Cautions

Antennas

Do not use any portable radio that has a damaged antenna. If a

damaged antenna comes into contact with your skin, a minor burn

can result.

Batteries

All batteries can cause property damage and/or bodily injury such as

burns if a conductive material—like jewelry, keys or beaded chains—

touch exposed terminals. The conductive material may complete an

electrical circuit (short circuit) and become quite hot. Exercise care in

handling any charged battery, particularly when placing it inside a

pocket, purse or other container with metal objects.

Exercise care when removing batteries. Do not use sharp or

conductive tools to remove the batteries.

FCC Licensing Information

Your Motorola radio operates on General Mobile Radio Service

(GMRS) frequencies and is subject to the Rules and Regulations of

the Federal Communications Commission (FCC). The FCC requires

that all operators using GMRS frequencies obtain a radio license

before operating their equipment. To obtain the FCC forms, please

visit the FCC’s Web site at wireless.fcc.gov/uls/index.htm?job=home

to source form 605 and 159, which includes all the instructions you

will need.

If you wish to have the document faxed or mailed, or if you have

questions, please use the following contact information:

Changes or modifications not expressly approved by Motorola may

void the user’s authority granted by the FCC to operate this radio and

should not be made. To comply with FCC requirements, transmitter

adjustments should be made only by or under the supervision of a

person certified as technically qualified to perform transmitter

maintenance and repairs in the private land mobile and fixed

services as certified by an organization representative of the user of

those services. Replacement of any transmitter component (crystal,

semiconductor, etc.) not authorized by the FCC equipment

authorization for this radio could violate FCC rules.

You can find the label with the FCC ID in the battery compartment.

Note: Use of this radio outside the country where it was intended to

be distributed is subject to government regulations and may be

prohibited.

Two-Way Radio

U er’ Guide

urning Your Radio On and Off

1. To turn on, press and hold until a channel number appears

and the radio beeps.

2. To turn off, press and hold until the display goes blank.

Setting the Volume

1. Press the to increase or to decrease the volume. The

volume level flashes and “V” displays.

Do not hold the radio close to your ear. If the volume is set to an

uncomfortable level, it could hurt your ear.

alking and Listening

To communicate, all radios in your group must be set to the same

channel.

1. To talk, press and hold .

2. When you are finished talking, release .

For maximum clarity, hold the radio two to three inches away from

your mouth and speak directly into the microphone. Do not cover the

microphone while talking.

Note: This radio does not have Interference Eliminator Codes. To

communicate with radios that use Interference Eliminator Codes, the

Interference Eliminator Code must be set to 0.

alk Range

Your radio is designed to maximize performance and improve

transmission range. Do not use the radios closer than five feet apart.

Monitor Button

Use this feature to see if there is anyone on the channel you have

selected.

1. Press and hold to check for the channel activity.

2. When you finish listening, release the button.

Push to alk imeout imer

To prevent accidental transmissions and save battery life, the radio

stops transmitting if you press for 60 continuous seconds.

Menu Options

Selecting the Channel

1. With the radio on, press . The current channel flashes.

2. Press or and select a channel.

3. Press or to confirm your selection.

Channels and Frequencies

ransmitting Call ones

To transmit your call tone to other radios set to the same channel as

your radio, press .

Note: To receive the call tone, radios that use Interference

Eliminator Codes must be set to 0.

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitting

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitting

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitting

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

GIANT TELECOM LIMITED

Customer : GI

Model Number : MG160

Description: LCD display graphics

& Line drawing (front view)

Version : R01

Date : Mar 04, 2013

PTT

Numbers for Channel,

Call Tone

1:1 Scale

14mm

11mm

2:1 Scale

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitting

Receiving

Scan

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

Display Screen Guide

Continue on back

MG160 Series

Control Buttons

GIANT TELECOM LIMITED

Customer : GI

Model Number : MG160

Description: LCD display graphics

&Line drawing (front view)

Version : R01

Date : Mar 04, 2013

PTT

Numbers for Channel,

Call Tone

1:1 Scale

14mm

11m m

2:1 Scale

Volume

Low Battery Icon

Keypad Lock

Transmitti ng

Receiving

Scan

Getting Started

Installing the Batteries

Each radio uses 3 AAA alkaline batteries.

Installing the hree AAA Alkaline Batteries

1. Turn the radio off.

2. With the bottom of the radio facing you, use a small screwdriver,

pen, or similar tool as illustrated below to remove the cover.

3. Insert the three AAA alkaline batteries with + and - polarity as

shown inside.

4. Reposition the battery cover and press down to secure.

Removing the Battery Cover

Push pen inwards with small amount of pressure and raise slightly upwards

Removing the hree AAA Alkaline Batteries

1. Turn the radio off.

2. With the back of the radio facing you, remove the cover.

3. Gently remove each alkaline battery by easing each battery out

individually.

4. Reposition the battery cover and press down to secure.

Notes:

• Exercise care when removing the batteries. Do not use sharp or

conductive tools to remove the batteries.

• Remove the alkaline batteries before storing your radio for

extended periods of time. Batteries corrode over time and may

cause permanent damage to your radio.

Attaching and Removing the Belt Clip

ook the belt clip into the notch at the top of the radio and slide it

down until it clicks into place.

To Remove

Squeeze the release latch together and slide the clip up and away

from the radio.

For a fax:

Contact the

Fax-0n-Demand

system

For mail service:

Call the FCC Forms

Hotline

If you have

questions about

the FCC License:

Call the FCC

1-202-418-0177 1-800-418-FORM

(3676)

1-888-CALL-FCC

(225-5322)

Channel Frequency Description Channel Frequency Description

1 462.5625 M z GMRS/FRS 12 467.6625 M z FRS

2 462.5875 M z GMRS/FRS 13 467.6875 M z FRS

3 462.6125 M z GMRS/FRS 14 467.7125 M z FRS

4 462.6375 M z GMRS/FRS 15 462.5500 M z GMRS

5 462.6625 M z GMRS/FRS 16 462.5750 M z GMRS

6 462.6875 M z GMRS/FRS 17 462.6000 M z GMRS

7 462.7125 M z GMRS/FRS 18 462.6250 M z GMRS

8 467.5625 M z FRS 19 462.6500 M z GMRS

9 467.5875 M z FRS 20 462.6750 M z GMRS

10 467.6125 M z FRS 21 462.7000 M z GMRS

11 467.6375 M z FRS 22 462.7250 M z GMRS

PTT

Numbers for Channel,

Call Tone

Volume

Low Battery Icon

Keypad Lock

Transmitting

Receiving

Scan

GIANT TELECOM LIMITED

Customer : GI

Model Number : MG160

Description: How to open the battery door

Version : R02

Date : Jun 14, 2013

Radio scale 1:1

Best Fitting for User Guide

Radio scale 1:1

Best Fitting for User Guide

Option A Option B