Mount-It! MI-6771 User manual
Thank you for choosing Mount-It
23
COMPATIBLE VESA SIZES
75x75 100x100 32
COMPATIBLE WITH
TVs UP TO
Mount-It!
Mount-It!
Mount and Accessories
Monitor Mounting Hardware
Spring Arm
Pole Grommet Bolt 4mm Hex Wrench 6mm Hex Wrench
Cable
Management
Clip (Pole)
Swivel Arm Mount Base VESA Plate Grommet
Plate
Cable
Management
Clip (Rear)
Arm
Connector
Missing Parts? Call us at (855) 925-5668 and we will ship replacement parts free of charge.
CHOKING HAZARD. Package includes small parts.
Not for children under 3 years. Adult supervision is required.
Check carefully to make sure there are no missing or defective parts. Some hardware provided may not
be used. Use the correct desk mounting and monitor mounting hardware suitable for your installation.
2.8”
min0.4”~max1.8”
min6.7”~max26.4”
min9.1”~max11”
min0.4”~max2”
1.9” 7.9”
3”
3”
3.9”
3.9”
4.5”
4.5”
14.2”
11”
DIMENSIONS & WEIGHT CAPACITY
Rated weight capacity is 19.8lbs*.
Caution:
Ensure all mounting surfaces are
capable of holding the weight of
your Monitor+Mount.
DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY.
SERIOUS INJURY OR
PROPERTY DAMAGE MAY
OCCUR!
5
• Clamp Installation Instructions: Open the clamp to be wider than the width of the desk then slide the
clamp into place in the desired location. Tighten the clamp back down using 6mm Hex Wrench (#L) until
it is secure. Slide the Cable Management Clip (#F) into place as shown.
4
Clamp Installation Option
• A grommet hole of 10-60mm is requred for installation. If a grommet hole is not present in your desk
surface, use a 3/8” drill bit to create a hole in the desired location.
• Use 6mm Allen Key (#L) to remove the bolt from the center of Mount Base (#C). This will also detach
the lower clamp portion. Store the removed parts to be able to convert the mount to a clamp configuration.
• Place the Mount Base (#C) over the grommet hole and insert Grommet Bolt (#J) through the desk and
connect To grommet Plate (#E) on the underside of the desk. Tighten with 6mm Allen Key (#L) until
secure. Slide the Cable Management Clip (#F) into place as shown.
Grommet Installation Option
Step 1
0.4”-2”
0.4”-1.8” 0.4”-1.8”
0.4”-2.4”
67
• Using the screwdriver end of 4mm Hex Wrench (#K) partially loosen the bolt on the outer end of the arm
connector.
• Insert the Swivel Arm (#B) into the end of the arm connector.
• Tighten the bolt back down to prevent the removal of the swivel arm.
Attach the Swivel Arm
• Use the screwdriver end of 4mm Hex Wrench (#K) to partially loosen the two bolts on the top of the
Clamp Base. Do not remove the bolts, stop loosening once bolts are loose enough to allow the pole to
be installed.
• Insert the threaded end of the Pole (#H) into the mount base and twist the pole until it is secure.
• Tighten the two bolts back down to secure the pole into place.
Insert the Vertical Pole
Step 2
• Attach the Cable Management Clip (#I) to the vertical pole approximately halfway between the base of
the pole and the desired location for the Arm Connector.
• Use 6mm Hex Wrench (#L) to partially loosen the bolt on the Arm Connector (#G).
• Slide the Arm Connector onto the vertical pole in the orientation shown, and hold it at the desired height.
• Tighten the bolt back down until it is secure and to fix the arm connector in place.
Install the Arm Connector
Step 3
Step 4
• Using the screwdriver end of the 4mm Hex Wrench (#K) partially loosen the bolt on the end of the swivel
arm.
• Insert the Spring Arm (#A) into the end of the swivel arm.
• Tighten the bolt back down to prevent the removal of the spring arm.
Attach the Spring Arm
Step 5
9
8
Attaching the VESA Plate Cable Management
• Select the appropriate size mounting bolt (Select one size #M-A or M-B) and washer (#M-C) for your
display’s mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the
correct bolt size for your display refer to your monitor user manual or contact the monitor manufacturer for
sizing information. Attach the VESA Plate using the selected bolts and tighten until secure. Do not
overtighten.
• There are covers for the cable management system on each segment of the mount arm. Remove them
by sliding the cover away from the center of the mount (do not pull or pry them away from the arm or the
cover will be damaged.) Route the cables beneath the covers and slide them back into place.
Connect the Monitor to the Spring Arm
• Turn the knob on the top of the VESA plate so that it is perpendicular to the monitor and the arrows are
pointing to the image of the unlocked lock.
• Slide the monitor and VESA plate into place on the end of the spring arm. Take care to not drop the
monitor too quickly before the gas spring tension is adjusted as shown in step 9.
• Turn the knob so that it is parallel to the monitor and the arrows are pointing to the image of the locked
lock.
Step 6 Step 8
Step 9
Step 7
11
10
Final Adjustments
Table of contents
Other Mount-It! TV Mount manuals
