AVF JZL102 User manual

JZL102 Leaflet No. 463442 rev01
25"
63cm
33lbs
15kg
STOP
Read through instructions before commencing installation.
If you have any questions about this product or issues with installation
contact the customer services helpline before returning this product to
the store. See jl.avfgroup.com/p/jzl102 for more information.
ALL
AVF Group Ltd. Hortonwood 30, Telford, Shropshire, TF1 7YE, England
CUSTOMER SERVICES HELP LINE NUMBER:
01952 670009

Fit the Mounting Plate
Assembly Overview
Fit the Wall Bracket
Attach the TV

Measure the TV fixing holes Width and Height
1
Fitting the TV Mounting Plate
2
Fitting the Wall Bracket
3
Assemble the Bracket
4
Fitting the Top and Bottom Covers
5
Retain all packaging in case the bracket needs to be returned.
Contents may vary from photography/ Illustrations.
You will not need all these parts, so expect there to be some left over
depending upon the specification of wall.
This product is intended for indoor use only. Use of this product outdoors
could lead to failure and personal injury.
It is the responsibility of the installer to ensure that the mounting wall is of
a suitable standard and void of any services (eg gas, electricity, water etc).
AVF accept no responsibility for any damage or loss caused by installing
this product in a sub standard wall.
Index
Attach the TV
6
TV Levelling and Tilt
7

Tools Recommended
Boxed Parts
A
Stud Finder Ø3mm (1/8")
Wood
Ø7mm (17/64")
Masonry
B
C

Ex1
2.5mm
TV Screws
Dx4
M4
16mm
Before you begin
Fx1 Gx1
Hx1
Lx1 Mx4 Nx4 Px1 Qx1 Ox1
Ix1 Jx1 Kx1
NYLON
5mm
Remove
bottom cover
iRemove
top cover
ii
Keep top and bottom covers until step 5.

Measure the TV fixing holes Width and Height
1
TV Fixing Holes
75 / 100mm
75 / 100mm
X
Y
100mm 75mm
75mm
100mm
Y
X
If X or Y are not equal to 75 or 100mm STOP installation now
and contact the customer help line.
!

Fitting the TV Mounting Plate
2
Top
C
D
If your TV has an irregular back or if you have
any issues fitting to the back of your TV with
the screws supplied, please call the customer
services helpline 01952 670009 / 0870 0609777 Dx4
M4
P
2.5mm
Px1

55mm (21/8")
Ø7mm
(17/64")
Ø3mm
(1/8")
Fitting the Wall Bracket
3
Ensure bracket is in the centre of the wood stud
!
Remove dust from hole
55mm (21/8")
Solid Wall Wood Stud
A
O
A
O

DO NOT over tighten screws
Tighten screws by hand only
!
DO NOT over tighten screws
Tighten screws by hand only
!
Lubricate screw thread with soap
Lubricate screw thread with soap
8mm (5/16")
MAX
Mx4 Nx4 Mx4
M
N
M

Assemble the bracket
4
J
NYLON
5mm
F
E
K
I
L
Q
Use your finger and thumb
to hold nyloc nut (K) steady
while you tighten screw ( )L
K
L

Fitting the Top and Bottom Covers
5
Fit the top cover
iii
Fit the bottom cover

iii
GH
Levelling Tilt
To remove TV
i. Remove parts G and H
ii. Lift safety plunger and pull TV away
(Safety plunger can be locked open by
turning anti clockwise after lifting)
Click!Click!
Attach the TV
6
TV levelling and Tilt
7
IMPORTANT
Ensure safety
plunger is down
!!