Mountain Buggy Evenflo Discovery User manual

These instructions are for the Carseat Clip that fits “Discovery™” and
“SecureRide™” infant car seats made by evenflo®, only.
This Carseat Clip fits the following model strollers:
IMPORTANT, KEEP FOR FUTURE REFERENCE
SCCEis1/4/04gen
2. Stroller Seat
WARNING
•Check you have correct Carseat Clip for
your car seat.
•Do not use this Carseat Clip until you have
read and understood the instructions!
•Never leave your child unattended.
•Do not use accessories not designed for your
stroller as they may be unsafe.
•Do not leave baby in car seat (on or off
stroller) for long periods of time.
The seat can be fully removed from stroller before fitting Carseat Clip
(see instructions in stroller Instruction Booklet) or if more convenient,
seat can remain on stroller with partial unfastening.
3. Partial Seat Unfastening
1
2
3
Unfasten two middle fasteners on both sides of stroller and peel
fabric back, exposing frame.
For Urban model only, loosen the strap underneath seat at point A.
Recline seat slightly.
STAGE 1
Pull sunhood support wire out of sunhood joint A. This operation is
child proof and therefore requires a degree of force. To assist in pulling
sunhood support wire out,push against stroller frame with other hand B.
Repeat step (1) on other side.
Unfasten sunhood fabric from stroller frame and seat near handle bar.
3
1
1. Removing Sunhood (both models)
2
A
B
Sunhood Joint
The Sunhood needs to be removed from stroller before fitting
Carseat Clip. NB: It can be replaced after Carseat Clip has been
fitted.
URBAN SINGLE - U1204
TERRAIN SINGLE - T1204
A
®CARSEAT CLIP INSTRUCTIONS
Discovery™ & SecureRide™
B
C
These instructions are for the Carseat Clip that fits “Discovery™” and
“SecureRide™” infant car seats made by evenflo®, only.
This Carseat Clip fits the following model strollers:
IMPORTANT, KEEP FOR FUTURE REFERENCE
SCCEis1/4/04gen
2. Stroller Seat
WARNING
•Check you have correct Carseat Clip for
your car seat.
•Do not use this Carseat Clip until you have
read and understood the instructions!
•Never leave your child unattended.
•Do not use accessories not designed for your
stroller as they may be unsafe.
•Do not leave baby in car seat (on or off
stroller) for long periods of time.
The seat can be fully removed from stroller before fitting Carseat Clip
(see instructions in stroller Instruction Booklet) or if more convenient,
seat can remain on stroller with partial unfastening.
3. Partial Seat Unfastening
1
2
3
Unfasten two middle fasteners on both sides of stroller and peel
fabric back, exposing frame.
For Urban model only, loosen the strap underneath seat at point A.
Recline seat slightly.
STAGE 1
Pull sunhood support wire out of sunhood joint A. This operation is
child proof and therefore requires a degree of force.To assist in pulling
sunhood support wire out,push against stroller frame with other hand B.
Repeat step (1) on other side.
Unfasten sunhood fabric from stroller frame and seat near handle bar.
3
1
1. Removing Sunhood (both models)
2
A
B
Sunhood Joint
The Sunhood needs to be removed from stroller before fitting
Carseat Clip. NB: It can be replaced after Carseat Clip has been
fitted.
URBAN SINGLE - U1204
TERRAIN SINGLE - T1204
A
®CARSEAT CLIP INSTRUCTIONS
Discovery™ & SecureRide™
B
C

WARNING
•Check car seat fits into Carseat Clip and buckle is
firmly fastened.
•Check Carseat Clip is located correctly onto stroller
frame. Refer back to diagrams to ensure positioning
of Snap Locks are correct.
•Check that car seat and Carseat Clip are secure and
cannot move forward, back, sideways or upwards.
•Do not use Carseat Clip if you are unable to secure
car seat or Carseat Clip. In this case, contact store
where stroller was purchased or distributor for your
country, for more help.
•Always remove car seat and Carseat Clip before
collapsing stroller.
Removing Car Seat from
Carseat Clip
1. Unbuckle Carseat Clip buckle.
2. Pull up car seat latch handle to
release car seat from Carseat Clip.
3. Lift car seat off Carseat Clip.
1. Open all four Snap Locks by lifting levers up.
2. Lift Carseat Clip off stroller frame.
Fitting Carseat Clip to Stroller Frame
Before placing Carseat Clip on stroller frame, the Snap Locks at
points B need to be removed and placed at points C(on both sides).
UsingAllen Key supplied,remove Snap Locks at points B (both sides)
by rotating screw in an anti-clockwise direction.
Using Allen Key supplied, place removed Snap Locks at points C
(both sides) by rotating screw in a clockwise direction until screw is
tight and Snap Locks are secure.
STAGE 2
Fitting Car Seat onto Carseat Clip
STAGE 3
Ensure the car seat latch has locked on
to the Carseat Clip bar.
2
WARNING
•Ensure baby is correctly and firmly strapped into
car seat, before placing on to Carseat Clip (check
car seat manufacturer’s instructions).
•When fitting car seat on to Carseat Clip, ALWAYS
keep a steadying hand on car seat and baby, until
Carseat Clip strap is securely fastened.
•Be aware of danger time between placement of car
seat on to Carseat Clip and point when Carseat Clip
strap is secured.
•It is recommended that you practise the following
instructions without baby in car seat.
NB:The Carseat Clip comes assembled for the Urban model.
Allen Key
CBACBA
Assembled for Urban Assembled for Terrain
To Assemble forTerrain Model
2
TERRAIN AND URBAN MODELS
Open all four Snap Locks by lifting up levers.
Press Carseat Clip on to frame so that top Snap Locks are directly
above sunhood joints (on both sides).
1
2
Close all Snap Locks down flat, making sure you hear the lock “click”
- indicating they are fully locked.
3
SNAP LOCKS OPEN
“CLICK”
SNAP LOCKS CLOSED
Place car seat in Carseat Clip so that
baby faces stroller handle bar.
1
1
Removing Car Seat from Frame
Sunhood Joint
Snap Locks
Sunhood
Joint
Snap Locks
URBAN TERRAIN
Buckle wide straps
across top of car seat and
tighten firmly by pulling
on free end of strap.
3
Carseat
Clip bar
Car seat
latch
Car seat
latch
handle
Allen Key
Straps
WARNING
•Check car seat fits into Carseat Clip and buckle is
firmly fastened.
•Check Carseat Clip is located correctly onto stroller
frame. Refer back to diagrams to ensure positioning
of Snap Locks are correct.
•Check that car seat and Carseat Clip are secure and
cannot move forward, back, sideways or upwards.
•Do not use Carseat Clip if you are unable to secure
car seat or Carseat Clip. In this case, contact store
where stroller was purchased or distributor for your
country, for more help.
•Always remove car seat and Carseat Clip before
collapsing stroller.
Removing Car Seat from
Carseat Clip
1. Unbuckle Carseat Clip buckle.
2. Pull up car seat latch handle to
release car seat from Carseat Clip.
3. Lift car seat off Carseat Clip.
1. Open all four Snap Locks by lifting levers up.
2. Lift Carseat Clip off stroller frame.
Fitting Carseat Clip to Stroller Frame
Before placing Carseat Clip on stroller frame, the Snap Locks at
points B need to be removed and placed at points C(on both sides).
UsingAllen Key supplied,remove Snap Locks at points B (both sides)
by rotating screw in an anti-clockwise direction.
Using Allen Key supplied, place removed Snap Locks at points C
(both sides) by rotating screw in a clockwise direction until screw is
tight and Snap Locks are secure.
STAGE 2
Fitting Car Seat onto Carseat Clip
STAGE 3
Ensure the car seat latch has locked on
to the Carseat Clip bar.
2
WARNING
•Ensure baby is correctly and firmly strapped into
car seat, before placing on to Carseat Clip (check
car seat manufacturer’s instructions).
•When fitting car seat on to Carseat Clip, ALWAYS
keep a steadying hand on car seat and baby, until
Carseat Clip strap is securely fastened.
•Be aware of danger time between placement of car
seat on to Carseat Clip and point when Carseat Clip
strap is secured.
•It is recommended that you practise the following
instructions without baby in car seat.
NB:The Carseat Clip comes assembled for the Urban model.
Allen Key
CBACBA
Assembled for Urban Assembled for Terrain
To Assemble forTerrain Model
2
TERRAIN AND URBAN MODELS
Open all four Snap Locks by lifting up levers.
Press Carseat Clip on to frame so that top Snap Locks are directly
above sunhood joints (on both sides).
1
2
Close all Snap Locks down flat,making sure you hear the lock “click”
- indicating they are fully locked.
3
SNAP LOCKS OPEN
“CLICK”
SNAP LOCKS CLOSED
Place car seat in Carseat Clip so that
baby faces stroller handle bar.
1
1
Removing Car Seat from Frame
Sunhood Joint
Snap Locks
Sunhood
Joint
Snap Locks
URBAN TERRAIN
Buckle wide straps
across top of car seat and
tighten firmly by pulling
on free end of strap.
3
Carseat
Clip bar
Car seat
latch
Car seat
latch
handle
Allen Key
Straps