Mountup MU0021 User manual

Mantel Arm Mount
This bracket is made of recyclable steel.
MU0021 INSTALLATION INSTRUCTION
If you have any questions, please contact us via [e-mail]
(A3)
44~143LBS
20~65KG
WEIGHT:
Max:800x600mm/32x24"
Min: 300x200mm/12x8"
55"~100"

2 of 16
WARNING
•
Be sure to read this entire manual thoroughly and you fully understand all the
instructions and warning before attempting to begin your installation.
•
Sufficient expertise is required for installing of this product. Be sure to subcontract the
installation to a qualified person. Ensure special attention to safety is paid during
installation. MOUNTUP mount is not liable for any damage or injury caused by
mishandling or improper installation, or by installing anything other than the specified
product.Your statutory rights, (if any) are not affected.
If the safety precautions are not observed or the product is used incorrectly, it may
result to serious injury or damage to your wall and TV.This instruction manual shows
the correct handling of the product and important precautions necessary to prevent
accident. Be sure to read this manual thoroughly and use the product correctly.Keep
the manual available for future reference.
•
Ensure your hands and fingers stay clear from the adjustable moving mechanics at
the back of the bracket. This is
to avoid your fingers getting trapped. Please supervise
children when this product is in use.
•
This product is supplied with small parts for installation. For your children’s safety
please keep out of reach of children at all times.
•
This product should only be installed by someone who has a basic knowledge of
building construction,installations and fully understands these instructions.
•
Made sure that the supporting surface will safely support the combined load of the
mount,the display and all attached hardware and components.
•
This wall bracket will supporting displays(LCD,Plasma).The maximum load capacity
is 143 pounds.
•
If mouting to a wall of wood stud construction,be sure that mounting bolt are anchored
to the center of the studs,When installing the TV mount on a concrete wall, the wall
must be at least 8”(203mm) thick with a minimum compressive strength from 2500 to
3000 psi(17.2 to 20.7 MPa),the concrete wall must meet ASTM C39.When installing
the TV mount on a cinder block wall, the cinder blocks must meet ASTM C216
specifications and have a minimum nominal width of 8”(203mm). Be sure to mount in
a solid part of the block,generally 1”(25 mm) minimum from the side of the block.
Do not drill into mortar joints! If plaster/drywall is thicker than 16mm, custom fasteners
must be supplied by the installer.
•
Always have someone assist you to lift and position your equipment.•
Tighten screws and bolts firmly,but do not over tighten.Over tightening can damage the
items and greatly reduce their ability to hold.Please refer to suggested torque values
where applicable in these instructions.
•
•Screws must be tightly secured,but do not overtighten any screws(especially the four
Hex Bolt Screws M8x63.5mm) or damage can occur and product may fail.

3 of 16
Tools Needed for Assembly
Table of Contents
Parts List............................................................................................................................................4
Critical requirements of the installation ...................................................................................5
Installation of the bracket................................................................................................................6-8
Installation of Screen.....................................................................................................................9-11
Adjustment of the spring pressure....................................................................................................12
Leveling adjustment .........................................................................................................................13
Tilting angle adjustment .................................................................................................................14
Product dimensions .........................................................................................................................15
Cauton and Maintenance .................................................................................................................16
Optional Tools
Before you begin, please verify that all components are included and undamaged.
If any parts are missing or damaged,contact Product Supplier,Never proceed with
missing or damaged parts!
Lay out all components and make sure you identify that each one has a match
in the diagram.Some of the parts included will not be used during installation.
Do not proceed if you do not understand and indentify all of the components.
Required Tools
3/16” 3/8”

4 of 16
B
AA CC
DD EE
FF GG
K L M
A
C
2
BB
hook(x2)handle(x1)
washer(x4)
Non-slip nuts(x4)
wallboard(x1)
front-panel(x1)connecting rod(x1) bracket(x1)
E
F
4
4
4
4
4
6
4
4
M8x25
M8x12
M6x25
M6x12
6.2x16x1.5
6.2x16x1.5
philips pan head screw
C
washer(1)
washer(1)
D
4
philips pan head screw
philips pan head screw
philips pan head screw
M6x8
philips pan head screw
2M6x25
M8x10
philips pan head screw
allen pan head screw
B4
H
J
K
L
4
G
17.0x9.0x14.0
spacer
N
M
M8x63.5
M10x60
M6
4
8.2x2.0x16
washer(2) 4
I
Hex bolt screw
Expansion pipe
Non-slip nuts
1 M10
spanner
1 M5
Hexagon wrench
2 L150
Cable ties
O2 M8
Hexagon wrench
with your product.
Parts may appear slightly different than illustrated.
Before you b egin, make sure all parts shown are included
Parts List
Description
A115x15x40
Wall panel cover(x2)
FG J DIE
H
1
Hexagon wrench
M8(x2)
O1
O2
Spanner
M10(x1)
Hexagon wrench
M5(x1) Cable Ties(x2)
N

5 of 16
•Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and
components, Bracket installation need two people together to complete.
WARNING
CRITICAL requirements of the installation
Temperature at the front edge of mantle should
never exceed 110° F(43 ).
Mantle must not extend from mounting surface
more than 16 inches.
The space above the mantle must be taller than the wallboard.
The required space depends on how far out the mantle extends.
Refer to chart below and add this additional height to wallboard
height to determine if space is tall enough.
If the main wall is wooden,There must be at least 2 studs
available for mounting.If the main wall is concrete or brick
wall,please refer to the S4 installation points. Mind you,
the wall covering must not exceed 5/8 inches thick.
TV weight must be between 44~143Ibs(20~65kg)
and have a screen size from 55” to 100”.
Consult Manual for verification.
TV Owner's
110°F
MAX.
16 inches
MAXIMUM
2 STUDS
(This two studs need along the
mantel center symmetric,and
the center distance between
two studs not more than 25”)
If mantle extends:
Less than 8 inches
8 - 11 inches
11 - 13 inches
13- 16 inches
This is required space height:
TV wallboard height plus 5 inches
TV wallboard height plus 6 inches
TV wallboard height plus 7 inches
TV wallboard height plus 8 inches
Wallboard height
Mantle
Extends
Space height
from 55” to 100”
12
3
5
4
WEIGHT:
44~143Ibs
(20~65kg)
C
L

6 of 16
Installation of the bracket
Measure the centerline of the mantle. Mark
with tape on the wall.
S1 S2 Locate at least two studs with a stud finder. Locate the
center of these studs by using a sharp awl or finish nail
poked through the drywall to locate each edge. Lag bolts
must be installed into the CENTER of the studs.
C
L
C
L
Please reference point 5 at page 5 to punch, please make sure that the four
mounting holes don’t have too big deviation.
S3
Cutout shown
for reference
C
LC
L
C
L
C
L
C
L
6mm(3/16”)
68mm
(2.7”)
6mm
(3/16”)
For the wood stud installation,
you MUST NOT use the exp-
ansion pipes we provided in M.
CL CL CL
plywood wall wood stud wall
CL
CAUTION

Please reference point 5 at page 5 to punch,If the main wall is concrete or brick wall,
you must use the expansion pipe we provided in M.
S4
C
L
10mm(3/8”)
M
In order to have a better installa-
tion,it is necessary to inlay one
wire cassette on the wall.
10mm
(3/8”)
68mm
(2.7”)
7 of 16
Installation of the bracket
Install wallboard(CC) using Hex bolt screws and washers(L).please let the
pre-set wire go through the hole as illustrated in the picture. Tighten the
Hex bolt screws until they are pulled firmly against the wallboard.
If the wood studs are off-center above the
mantel, the center steel plate of wallboard(CC)
can be reassembled to left or right for TV
centering, then tighten securely. There are
different hole positions on the wall plate.
S5
CAUTION
NOTE:
Don't over tighten!
A
(magentic spirit level)
L
L
CC
CUTAWAY VIEW
INCORRECT
CORRECT
wallplate
plaster/
drywall
concrete
wallplate concrete
plaster/
drywall
CAUTION
Do not drill into mortar joints!

8 of 16
Installation of the bracket
Take out K/EE/FF/N(spanner M10) from the packaging , installation as
illustrated in the picture.
S6
Take out N/J from the packaging ,lock the four allen pan head
screws(M8x10) with Hexagon wrench in N,then use cable ties
in N to tie up the wires,as is shown in the pictures below.
S7
N
(spanner M10)
K
EE
FF
keep the up direction uniform
N
J
(Hexagon wrench)
(screw M8x10)
N
(Cable ties)

Installation of Screen
S8
S9
Short Screw
TV back
No,just choose the screws and washers
Washer
Hook
Highly recommended to add spacers for more spacing between wall mount and TV.
Washer
Need Spacer or NOT?
Yes,choose the appropriate screws, washers and spacers for your TV
Spacer
Long Screw
Hook
TV back
Select TV Screws
M6 M8
When attaching brackets to the flat screen,be careful not to over tighten
screws and be sure that screws do not bottom out in the mounting holes.
Thread screws by hand into the threaded holes on the back of your TV to select
which screw diameter fits your TV.
Correct CorrectToo Long Not VerticalToo Short
9 of 16

Position your hooks over your TV hole pattern -makingsure the hooks are centered
and level over the TV hole pattern.
Secure the hooks using your screw/washer/spacer selection:
(a) for Flat Back
(b) for Round Back/Extra space
Ensure hook is securely fastened before moving on to the next step.
CAUTION:
Attach the Hooks
S10
(a) Flat Back
(b) Round Back /
Extra Space
B/D
F
BB
(D don’t need F)
(only for B)
C/E
(E don’t need F)
F
(only for C)
G
BB
10 of 16

11 of 16
Take out H/I/AA/DD from the packaging,according to the size of the TV,adjust to the
appropriate location,as shown in the picture below,then lock with cross screwdriver.
Lift the TV,through hooks for hanging
onto the bracket panel,then press the
safety locks on the hooks and fix it
with the screws(H).
Take out GG from the packaging,
buckle it to the wall plate.
S13
S11
S12
GG
Hx4
(screw M6x8)
Ix2
(screw M6x25)
Attach the Handle
Hx2
(screw M6x8)
AA DD
BB
DD
Note:Take care not to damage the TV when putting the
connecting rod(DD) into the small gap of the hook(BB).

adjustment of the spring pressure
Increase the
constant force
Reduce the
constant force
Attention: The weight of the TV set in the weighing range
B:The TV sets up, turn to “ - ” until free hovering.
A:The TV sets can be hovering at any height, don not need to adjust.
C:The TV sets down, turn to “ + ” until free hovering.
Adjustable the bracket’s constant force
18.0/40.0
24.0/52.9
32.0/70.5
40.0/88.2
48.0/105.6
56.0/123.4
60.0/132.2
70.0/154.0
KG/LBS
STOP LINE
!
STOP LINE
!
Accor ding to different load weight,
pleas e adjust the gas spring int o
suitable posi tion with in the sco pe
of the scale, excessiv e adjustment is fo rbidden!
ATTENTION
Refer to this
above cylinder
as a pointer
12 of 16
S14 Adjust the spring pressure to the appropriate level with the socket wrench and O1
or O2 (the hexagon wrench M8 that we provided).
O1
O2
OR

TV leveling adjustment (-5°/+5°)
13 of 16
!
WARNING:
Do Not put hands into Lifting Mechanism.
The power of the Lifting Mechanism can cause bodily injury!
If needed,loosen 4 leveling nuts on the rear of TV plate by maximum 2
turns with the N(spanner), adjust to level, and retighten to secure.
N
(spanner M10)
N
(spanner M10)
±5°
S15

14 of 16
Handle
② Pull out and hold the handle.
③ Turn the handle in the opposite direction.
④ Push and release the handle.
⑤ Turn handle again to tighten or loosen.
① Turn handle (loosen or tighten)
until stopped by mount.
How to tighten or
loosen the handles
Tilting angle adjustment (-15°/+3°)
Loosen handles, adjust TV to your desired position,
then tighten handles.
Handles
S16
-15 °
+3°

mm042OTXAM
°
°
-15 ~+3:tlit
MAX820
mm0.016
mm7.638
0.82
0.001
°5±:level
°5±:level
swivel：±30°
mm8.004
from 150mm to 536mm
MAX127°
mm008OTXAM
PRODUCT DIMENSIONS
15 of 16

Do not use strong acidic or alkaline liquid to wipe the product.
Never allow children to climb,stand,hang or play on any part
of Mantel Arm Mount.
Check that the mantel arm mount is secure and safe to use
at regular intervals(at least every three months).
please use the cloth stained with water to wipe it.
Don’t disassemble the product randomly.
16 of 16