Mountup MU0031 User manual

Table Top TV Stand
Installation Manual
If you have any questions , please contact our customer service.
37~70"
V1.0
Min: 150x100mm / 6x4"
Max: 600x400mm / 24x16"
88lbs
40kg
MU0031

01
Before getting started,
let's make sure this TV stand is perfect for you!
88 LBS
(40 KG)
Yes — Perfect!
No — This mount is NOT compatible.
Yes — Perfect!
No — This mount is NOT compatible.
If this mount is NOT compatible, please contact our customer service to nd a compatible mount.
4. Safety Caution
3. Installation Tools
(Not Included)
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety
of the installation, assembly or use of this product, please contact our
customer service.
●Incorrect installation may result in product damage or body injury.
MOUNTUP shall bear no responsibility for any damage or injury resulted
from incorrect installation, incorrect assembly or misuse.
●Do not apply this product to any purpose not indicated by MOUNTUP.
Screwdriver
2M
Band Tape
2m
2. Does your TV
(including accessories)
weigh less than
88LBS (40KG)?
1. Is your TV VESA
equal to/greater than
150x100mm/6x4" and
equal to/less than
600x400mm/24x16"?
MAX:
400mm/16"
MAX:600mm/24"

02
NOTE: Not all hardware included will be used.
PACKAGE CONTENTS
① (×1)
Base
② (×1)
Support Pillar
A (×3)
Bolt M6×30mm
I (×4)
Foot Pad
B (×1)
Washer
G (×2)
Safety Lock
H (×2)
Wire Clip
M-D (×4)
M8×45mm
M-C (×4)
M8×15mm
M-E (×4)
M8×65mm
M-B (×4)
M6×30mm
M-A (×4)
M6×15mm
C (×4)
M6 Nut
D2 (×4)
D6 Washer
D1 (×4)
Bolt M6×50mm
M-F (×4)
D5mm/D8mm
M-H (×8)
H10mm
M-G (×8)
H5mm
TV Screw/Washer/Spacer
F (×1)
Plastic Cover
E (×4)
Bolt M6×10mm
J1 (×1)
4mm Allen Key
J2 (×1)
Wrench
⑥ (×1)
Connecting Plate
⑦ (×1)
Angle Adjuster
⑤ (×2)
TV Plate
③ (×1)
Support Pillar
④ (×2)
TV Bracket

03
STEP 1: Support Pillar Installation
Step 1-1: Connecting two Support Pillar ( ②&③ ). Insert 4pcs Screws (E) through the holes of Support
Pillar ( ②&③ ), use the 4mm Allen Key (J1) to tighten them.
Step 1-2: Put Base ( ① ) on the table, put washer (B) and M6×30mm bolts (A) on the base, put Plastic Cover
(F) and Support Pillar ( ③ ) under the base, then tighten the bolts (A) with the 4mm allen key (J1).
A
B
①
F
③
J1
Note: Clip holes
toward backside.
③
②
E
②
③
J1
Note: Clip holes
in the same side.
Checklist
② (x1) Support Pillar
③ (x1) Support Pillar
E (x4) Bolt M6×10mm
J1 (x1) 4mm Allen Key
Checklist
① (x1) Base
A (x3) Bolt M6×30mm
B (x1) Washer
F (x1) Plastic Cover
J1 (x1) 4mm Allen Key
Table

04
STEP 2: Apply Foot Pads to the Base
Tear o plastic lm of Foot Pads (I), then attach Foot Pads (I) on the bottom of the Base ( ① ) at the corners.
Checklist
I (x4) Foot Pad
STEP 3: TV Plate Installation
Step 3-1: Connecting TV Plate ( ⑤ ) and Angle Adjuster ( ⑦ ) by using Connecting Plate ( ⑥ ) and M6 Nuts (C).
Use the Wrench (J2) to tighten the nuts.
①
I
Table
Checklist
⑤ (x2) TV Plate
⑥ (x1) Connecting Plate
⑦ (x1) Angle Adjuster
C (x4) M6 Nut
J2 (x1) Wrench
C
⑦
⑥
⑤
⑤
J2

05
STEP 3: (Continued)
Step 3-2: Choose the appropriate position (three options) for your TV Plate, connecting TV Plate Unit to
Support Pillar( ② ) by using Bolts(D1) and Washers(D2). Use the 4mm allen key(J1) to tighten them.
55mm
55mm
55mm
②
TV Plate Unit
D1 D2
J1
Note:
Three choices for
height adjustment.
Note: Arrow must be up!
Checklist
D1 (x4) Bolt M6×50mm
D2 (x4) D6 Washer
J1 (x1) 4mm Allen Key

06
STEP 4: Attach the TV Brackets
1-1 Select TV Screws
1-2 Need Spacer?
Yes, choose the appropriate screws, washers, and spacers for your TV.
TV back
Bracket
Long Screw
Spacer
Washer
No, just choose the screws, washers.
Bracket Washer
TV back
Short Screw
M8
M6
No!
1-3 Attach the TV Brackets
Attach the TV Brackets ( ④ ) to the back of TV.
secure it with TV screws, washers and spacers.
Checklist
④ (x2) TV Bracket
TOP OF TV
May be needed
Not for M8 Screws
M-F
M-G M-H
M-C
M-A M-B
M-E
M-D
④

Correct

Correct

Too Long

Too Short

Not Vertical
1
43
2
Flat Back Round Back
Inset Holes Cables

07
Choose the appropriate position (three options) for your TV. Hang TV with brackets onto the TV plate.
Put the safety lock (G) in place and tighten the xing screw to the TV plate securely.
STEP 5: Attach TV with Brackets to TV Plate
Hang on top
of TV plate
To the bottom
Lock to the bottom
of the TV Plate
G
45mm
Note:
Three choices for
height adjustment.
45mm
Checklist
G (x2) Safety Lock

08
STEP 6: Cable Management
Attaching Wire Clips (H) into the holes of Support Pillar ( ②&③ ).
Manage cables with the Wire Clips (H).
H
③
②
Checklist
H (x2) Wire Clip

09
Adjustments
-20° +20°
Swivel Adjustment
Refer to below illustrations to adjust swivel angle.
Tilt Adjustment (If necessary)
1. Loosen 4 tilting bolts by MAXIMUM 1 turn with Wrench (J2).
2. Hold the TV with your hand, adjust TV to your desired angle.
3. Tighten 4 tilting bolts with Wrench (J2).
Wall
Note: When the TV Stand is placed
against the wall, the actual swivel
angle is determined by the screen size.
0°
+5°
J2
Tilting
Nuts
Clockwise,
Tighten
Counter-clockwise,
Loosen
Tighten
Loosen
Loosen
Tighten

10
Product Dimensions
110mm
/4.33"
MAX:
400mm/16"
MIN:
100mm/4"
MAX:600mm/24"
MIN:150mm/6"
23mm
/0.91"
MAX:
788mm
/31.02"
MIN:
588mm
/23.15"
+20°/-20°
633mm/24.92"
571mm
/22.48"
280mm
/11.02"
420mm/16.54"
40mm
/1.57"
70mm
/2.76"
130mm
/5.12"
+5°
0°

If you have any questions, please contact our customer service.
• Never allow children to climb, stand, hang, or play on any part of TV or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals
(at least every three months).
CAUTION AND MAINTENANCE: