Movincool Office Pro 63 User manual

OPERATION MANUAL
OFFICE PRO 63
Unit Serial Number Range: 0711XXXX630 to Present
(From July 2011 to Present)
READ THIS MANUAL CAREFULLY FOR INSTRUCTIONS ON CORRECT
INSTALLATION AND USAGE AND READ ALL SAFEGUARDS
SECCIÓN EN ESPAÑOL
SECTION EN FRANÇAIS
AVAILABLE AT WWW.MOVINCOOL.COM

SERIAL NUMBER LOCATION AND IDENTIFICATION
Nameplate Label Position
Nameplate Label
COOLING AMPS. WITH PUMP
COMPR. OUTPUT
REFRIGERANT/TOTAL CHARGE
DESIGN PRESSURE LO/HI
PART NO./WEIGHT
SERIAL NO.
Month Model
Sequential
Number
Year
© 2017 DENSO PRODUCTS AND SERVICES AMERICAS, INC.
All rights reserved. This book may not be reproduced or copied, in
whole or in part, without the written permission of the publisher. DENSO
PRODUCTS AND SERVICES AMERICAS, INC. reserves the right to
make changes without prior notice. MovinCool®, Office Pro®, and
SpotCool® are registered trademarks of DENSO Corporation.

OPERATION MANUAL
OFFICE PRO 63

Table of Contents
SERIAL NUMBER LOCATION AND IDENTIFICATION....................................2
FOREWORD.......................................................................................................5
Definition of Terms............................................................................................5
GENERAL WARNINGS & CAUTIONS ..............................................................6
INVENTORY .......................................................................................................7
INSTALLATION..................................................................................................8
Choosing an Installation Site ...........................................................................8
Moving the Unit .................................................................................................9
Plugging in the Unit ........................................................................................10
Warning Signal Connection ...........................................................................11
Fire Alarm Control Panel Connection ...........................................................12
FEATURES.......................................................................................................13
OPERATION.....................................................................................................14
Control Panel ...................................................................................................14
LCD Indicators.................................................................................................15
Set Clock ..........................................................................................................16
Operating in COOL Mode ...............................................................................16
Operating in FAN ONLY Mode .......................................................................17
Changing from FAN ONLY Mode to COOL Mode.........................................17
Keypad Lock ....................................................................................................17
How to Set a Program .....................................................................................18
How to View and Delete Program ..................................................................19
How to Run and Stop Program ......................................................................19
Operating Modes .............................................................................................20
Self-Diagnostic Codes ....................................................................................21
Emptying the Drain Tank (If equipped) .........................................................22
Drain Pump ......................................................................................................23
HOSE INSTALLATION ....................................................................................24
INSPECTION & MAINTENANCE.....................................................................25
Emptying the Drain Tank ................................................................................25
Air Filters Maintenance...................................................................................25
Removing the Air Filters...........................................................................25
Cleaning the Air Filters.............................................................................25
SEASONAL MAINTENANCE ..........................................................................26
In-Season .........................................................................................................26
Off-Season .......................................................................................................26
TROUBLESHOOTING .....................................................................................27
TECHNICAL SPECIFICATONS .......................................................................28

5
FOREWORD
Congratulations on purchasing the MovinCool portable air conditioner. This
manual explains how to assemble, install and operate the MovinCool Office Pro
63 portable air conditioning unit. Please read this operation manual thoroughly to
familiarize yourself with the features of the unit and to ensure years of reliable
operation.
You may also find it useful to keep this operation manual on hand for reference.
Components and/or procedures are subject to change without prior notice.
Definition of Terms
WARNING: Describes precautions that should be observed in order to
prevent injury to the user during installation or unit operation.
CAUTION: Describes precautions that should be observed in order to
prevent damage to the unit or its components, which may occur during
installation or unit operation if sufficient care is not taken.
Note: Provides additional information that facilitates installation on unit operation.

6
GENERAL WARNINGS & CAUTIONS
• All electrical work must be performed by qualified electrical personnel. Repair
to electrical components by non-certified technicians may result in personal
injury and/or damage to this unit. All electrical components replaced must be
genuine MovinCool parts, purchased from an authorized dealer.
• The power source for this unit should be a dedicated single outlet circuit with
UL recognized short-circuit and ground fault protective breaker.
• Because of potential safety hazards under a certain condition, we strongly
recommend against the use of an extension cord.
However, if you still elect to use an extension cord, it is absolutely necessary
that it is a UL listed, 3-wire grounding type appliance extension cord, having a
3-blade and a 3-slot receptacle that plugs into the appliance.
The marked rating of the extension cord should be 460 V, 20 A or equivalent.
• This unit is equipped with a 6-foot (1.8 m) UL recognized LCDI power cord.
If replacement, fixed location (hard wired) or power cord lengthening
(extension cord) is required, contact your dealer or a qualified electrician for
approved methods.
• Never fold or place heavy objects on the power cord.
This could result in damage to the power cord causing electrical shock or fire.
• Turn this unit off and unplug the power cord when the power cord is damaged.
• Do not place water or any other liquid on this unit. This can cause damage to
the unit and increase the risk of electrical shock.
• Do not use water to clean inside this unit. Exposure to water can destroy the
insulation and electrical components, leading to electric shock.
• Interior cleaning of this unit must be performed by authorized personnel only.
Consult your MovinCool dealer.
• Do not sit or stand on this unit.

7
INVENTORY
After unpacking your MovinCool unit, please check to make sure you have the
following items:
1. Office Pro 63 MovinCool Unit (1)
2. Operation Manual / Product Registration (1)
Note: If any of these items were not included in the box or appear damaged,
please contact your MovinCool reseller for replacement.
Office Pro 63 Unit
ILL01032-00
Operation Manual /
Product Registration

8
INSTALLATION
Choosing an Installation Site
CAUTION: Following are some precautions to consider before choosing
your installation site. Please review carefully as improper installation may
result in personal injury or damage to the unit.
1. Do not use the unit in areas where leakage of flammable gas may occur.
2. Do not use the unit in areas where it is exposed to rain or water.
3. Do not use the unit in an atmosphere of excessively corrosive gas or vapor.
4. Do not use in areas where the temperature is outside the allowable operating
range.
5. Do not install the unit in sloping areas. The unit may move or topple over even
if the casters are set to the LOCKED position.
6. Install the unit in areas that can with-stand the weight of the unit.
*1: Approximate weight of the unit when the drain tanks are full of water.
7. Allow 24 inches (610mm) of unobstructed airflow for both the air inlets and
outlets.
8. Do not use the Office Pro 63 unit at condition above 106°F (41°C) 50% RH.
Model Unit Weight *1
Office Pro 63
(Serial number from 0417XXXX630 to Present)
748 lbs (339 kg)
Office Pro 63
(Serial number from 0711XXXX630 to 0317XXXX630)
739 lbs (335 kg)

9
INSTALLATION (cont.)
Moving the Unit
Unlock all 4 casters and push the MovinCool unit, using the front or rear handles,
to a flat, level surface and set the casters back to the LOCKED position.
Office Pro 63 Unit ILL01033-00
Front Handle
Rear Handle
ILL00044-01
Locked
Unlocked

10
INSTALLATION (cont.)
Plugging in the Unit
1. Check the prongs and surface of the power cord plug for dust/dirt. If dust and/
or dirt are present, wipe off with a clean, dry cloth.
2. Check the power cord, plug and prongs for damage or excess play. If any
damage or excess play is found, contact your MovinCool dealer for
replacement.
WARNING:
1. If the power cord or plug is damaged, replacement must be
performed by qualified electrical personnel.
2. Do not connect or disconnect the power cord or attempt to operate
buttons with wet hands. This could result in electrical shock.
3. Because of potential safety hazards under a certain condition, we
strongly recommend against the use of an extension cord. However,
if you still elect to use an extension cord, it is absolutely necessary
that it is a UL listed, 3-wire grounding type appliance extension cord,
having a 3-blade and a 3-slot receptacle that plugs into the appliance.
The marked rating of the extension cord should be the following
rating or equivalent.
3. Check the power supply outlet rating and fuse size to match with table below.
CAUTION: The power source should be a dedicated single outlet
circuit with UL recognized short-circuit and ground fault protective
breaker. Do not share the power supply outlet with any other instrument
or equipment. The minimum power supply rating and the recommended
fuse size are listed above.
Note:
1. Make sure the power supply outlet is free of dirt, dust, oil, water, or any other
foreign matter.
2. The Office Pro 63 is equipped with an approved NEMA plug configuration (L16-
20). The appropriate outlet must be used for this plug type.
Model Rating of Extenstion Cord
Office Pro 63 460 V, 20 A
Model Minimum Power Supply Rating Recommended Fuse Size
Office Pro 63 460 V, 3 Phase, 60 Hz, 20 A 20 A maximum

11
INSTALLATION (cont.)
Warning Signal Connection
(Output Signal Terminal L+ and L-)
The controller is equipped with a warning signal output relay type (Form C, normal
open dry contact) which can be used to monitor the failure condition.
Relay contactor (not connector) is closed when the following condition has
occurred:
a. Tank full
b. Temperature sensor fails
c. High pressure switch error
The relay output contactor is rated 2A at 30VDC or 2A at 30VAC (resistive load)
and it is compatible with various warning devices such as alarm speaker, light
indicators, etc.
Connecting Warning Signal From Controller
1. Remove service panel from the rear of the unit.
2. Squeeze the inner latches and push out the black cap from inside the panel.
3. Use recommended warning signal wire size from 16AWG to 26AWG for a solid
wire, or 16AWG to 22AWG for a stranded wire with ring terminal for #6 stud
size.
4. Connect warning device to terminal L+ and L- according to its polarities.

12
INSTALLATION (cont.)
Fire Alarm Control Panel Connection
(Input Signal Terminal E+ and E-)
The controller is equipped with a normal open input signal, which can be
connected directly from the fire alarm control panel. When receiving the signal
from the fire alarm control panel, the unit turns off and does not turn back on until
it has been RESET.
Connecting Fire Alarm Control Panel to Controller
1. Remove service panel from the rear of the unit.
2. Squeeze the inner latches and push out the black cap from inside the panel
(see drawing of cap and inner latch shapes).
3. Use recommended warning signal wire size from 16AWG to 26AWG for a solid
wire, or 16AWG to 22AWG for a stranded wire with ring terminal for #6 stud
size.
4. Connect warning device to terminal E+ and E- according to its polarities.
ILL00046-01
Latch
Cap
Input Signal
Terminals
Output Signal
Terminals
E+
E-
L+
L-
ILL01023-00

13
FEATURES
For all models:
1. A digital electronic control panel, which allows the user to control the unit’s
operation easily.
2. Dual fan speeds (either HIGH or LOW) in both COOL and FAN ONLY modes.
3. Digital LCD display with blue backlight that indicates:
a. Clock with day and time
b. Room temperature and set point temperature
(either Fahrenheit or Celsius)
c. Fan speed status
d. Cool mode status
e. Program start time and stop time
f. Program run and stop
g. Status codes
h. Keypad lock
4. The set point temperature can be adjusted between 65°F (18°C) and 90°F
(32°C) by the SET TEMP buttons ( / ).
5. Fire alarm control panel connection ready for automatic shut off.
6. Automatic shut off and warning signal output and alarm for temperature sensor
failure, cooling failure.
7. A condensate drain “TANK FULL” indicator (LED) and display (LCD).
8. An automatic restart feature when the power is lost and regained.
9. A condensate pump with safety switch shut off.

14
OPERATION
Control Panel
Before operating the unit, it is important to familiarize yourself with the basic
controls located on the control panel.
1. COOL Mode Button Activates/deactivates the COOL mode/turns the
unit off.
2. FAN Mode Button Activates/deactivates the high, low, and off fan
speed.
3. SET TEMP Buttons ( /)Temperature scale illuminates to indicate the
current LED temperatures being displayed are
either in °C or °F; also displays the clock when
programming.
4. ENTER Button Press to select set up value.
5. SET CLOCK Button Press to set clock (day and time).
6. SET PROG Button Press to set or view program.
7. RUN/STOP Button Activates/deactivates program(s).
8. TANK FULL LED Flashes when the drain tank is full.

15
OPERATION (cont.)
Control Panel (cont.)
LCD Indicators
Note: ROOM TEMP display range from 16°F to 109°F (-9°C to 42°C). In
Fahrenheit only, when display values are greater than 99°F, it displays values of
+0F (for 100°F),+1F (for 101°F) and +9F (for 109°F).
9. MO...SU Illuminates to indicate selected day of the week.
10. °C or °F Temperature displayed in either Fahrenheit or
Celsius (see Note).
11. AM/PM Illuminates to indicate AM or PM time of day.
12. PROGRAM Blinking during program editing mode.
13. PROGRAM ON Illuminates to indicate program is running.
14. START Illuminates to indicate program start time.
15. STOP Illuminates to indicate program stop time.
16. CLOCK Illuminates to indicate clock status.
17. FAN HI/LO Illuminates to indicate selected fan speed.
18. COOL ON/OFF Illuminates to indicate cool on or off.
19. LOCKED Illuminates to indicate key lock up.

16
OPERATION (cont.)
Set Clock
Prior to operating the Office Pro 63 users should set the clock of the controller to
the correct time as shown in the steps below.
1. Press and hold the SET CLOCK button
for 3 seconds or until beep.
(LCD indicates blinking “CLOCK” and
blinking “day of the week”.)
2. Press SET TEMP buttons to select day
of the week.
3. Press ENTER button to set hour.
4. Press SET TEMP buttons to select
desired hour.
5. Press ENTER button to set minute.
6. Press SET TEMP buttons to select
desired minute. Press SET CLOCK
button to exit set clock mode.
Note: User should check clock periodically to confirm clock accuracy.
Operating in COOL Mode
1. The unit can be operated in COOL mode by pressing the COOL ON/OFF
button (LCD indicates “COOL ON”).
Note: In COOL mode the unit can only be turned off by pressing the COOL
ON/OFF button again, not by pressing the fan buttons.
2. Change the fan speed by pressing the FAN HI/LO button.
3. Change the temperature set point by pressing the SET TEMP buttons ( / ).
Note: When turning the unit on, the set point and fan speed are determined by
the last operating mode. (This function does not apply to PROGRAM mode.)
Step 1 & 6
Step 2 to 5

17
OPERATION (cont.)
Operating in FAN ONLY Mode
1. The unit can also be operated in FAN ONLY mode by pressing FAN HI/LO
button (LCD indicates “FAN HI/LO” and “COOL OFF”).
2. The unit can then be turned off by pressing the FAN HI/LO button until fan
turns off (FAN ONLY mode speed sequences are HI→LO→OFF).
Changing from FAN ONLY Mode to COOL Mode
The COOL mode can be activated while the unit is operating in FAN ONLY mode.
To do this, simply press the COOL ON/OFF button (LCD indicates “COOL ON”).
Note: The FAN ONLY mode does not operate after the COOL mode has been
activated. After the COOL mode has been activated, the unit cannot be turned off
by pressing the fan buttons. The COOL ON/OFF button must be pressed.
Keypad Lock
Keypad lock disables all buttons on the controller panel except keypad lock and
unlock operations.
1. To lock, press and hold ENTER and SET CLOCK buttons simultaneously for
5 seconds.
2. To unlock, press and hold ENTER and SET CLOCK buttons simultaneously
for 5 seconds again.
Note: When the unit detects operation failure, keypad is unlocked automatically
and self-diagnostic code illuminates.

18
OPERATION (cont.)
How to Set a Program
SET START TIME
1. Press and hold the SET PROG button
for 3 seconds or until beep.
2. Press SET TEMP buttons to select day
of the week.
3. Press ENTER button.
4. Press SET TEMP buttons to select
desired hour.
5. Press ENTER button.
6. Press SET TEMP buttons to select
desired minute.
7. Press ENTER button.
SET STOP TIME
8. Press SET TEMP buttons to select day of the week.
9. Press ENTER button.
10. Press SET TEMP buttons to select desired hour.
11. Press ENTER button.
12. Press SET TEMP buttons to select desired minute.
13. Press ENTER button.
SET FAN SPEED
14. Press SET TEMP buttons to select desired fan speed.
15. Press ENTER button.
SET SET-POINT TEMPERATURE
16. Press SET TEMP buttons to select desired temperature.
17. Press ENTER button.
EXIT PROGRAM EDITING MODE
18. Press SET PROG button to exit program editing mode.
EDIT MULTIPLE PROGRAMS
19. Repeat step 1. to 18. to set up multiple programs.
Note: Maximum 7 programming sequences
Step 1 & 18
Step 2 to 17

19
OPERATION (cont.)
How to View and Delete Program
1. Press and hold the SET PROG button for 3 seconds or until beep.
2. To view edited program - While pressing and holding the SET PROG button,
press SET TEMP buttons ( / ) to scroll the program sequence.
3. To delete a program - Press ENTER and SET PROG buttons once
simultaneously.
4. To delete multiple program - Press and hold ENTER and SET PROG buttons
simultaneously.
How to Run and Stop Program
1. Press RUN/STOP button to activate preset program (LCD indicates
“PROGRAM ON”). During PROGRAM RUN mode, if you push RESET (press
FAN HI/LO and COOL ON/OFF buttons simultaneously for 5 seconds),
PROGRAM RUN mode is terminated. To resume PROGRAM RUN mode, you
must push RUN/STOP button again.
2. Press RUN/STOP button to stop program.
Note:
1. The unit returns to the previous mode if a program is turned off while it is
running.
2. The LCD continues to indicate “PROGRAM ON” during program activating.
3. Program can be set during power on standby, during unit running, or during
program running.
4. During programming, the unit returns to the previous mode if no activity occurs
within approximately 3 minutes.

20
OPERATION (cont.)
Operating Modes
Office Pro 63 operates in 2 modes, FAN ONLY and COOL. When in FAN ONLY
mode, the unit circulates the surrounding air, Office Pro 63 is equipped with an
automatic fan speed control when operating in FAN ONLY mode. When in COOL
mode, the compressor is operated and cool air is circulated. Office Pro 63 is
equipped with automatic condenser fan speed control depending on room
temperature.
Office Pro 63 operates in FAN ONLY mode for approximately 120 seconds before
the compressor engages.
(Time delay setting is around 120 seconds.)
1. Temperature Control
The room temperature thermistor allows the unit to switch automatically between
COOL and FAN ONLY modes. This is dependent upon inlet air temperature versus
set point temperature.
2. Fan Mode Control DIP Switch
The fan mode control DIP switch determines whether the fan continues to operate
or stop when the compressor cycles off. (Set point temperature equals inlet air or
room temperature.) The unit has been preset at the factory for continuous fan
operation.
3. Temperature Scale Display DIP Switch
The temperature scale display DIP switch changes the temperature(s) that are
displayed to either °C or °F. The unit has been preset from the factory to display the
temperature(s) in °F.
Note: If you wish to change the fan mode operation (OPERATE to STOP), and/or
the temperature scale display (°F to °C), contact your MovinCool reseller.