MRC CB15E User manual

4 Litre Blender
CB15E Operating Manual
Blender 4 Litre 120 volt - 230 volt
PLEASEREAD THIS MANUAL CAREFULLY BEFORE OPERATION
3, Hagavish st. Israel 58817
Tel: [phone], Fax: [phone] [email protected]
MRC.7.15

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed including
the following:
11. READ ALL INSTRUCTIONS.
12. To protect against electrical hazards, do not immerse the Blender Base in water or other
liquid.
13. Close supervision is necessary when any appliance is used by or near children.
14. Unplug from outlet when not in use, before putting on or taking off parts, and before
cleaning.
15. Avoid contacting moving parts.
16. Do not operate any appliance with a damaged cord or plug,or after the appliance malfunctions
or is dropped or damaged in any manner. Return appliance to the nearest authorized service
facility for examination, repair or electrical or mechanical adjustment.
17. The use of attachments including canning jars not recommended by the appliance
manufacturer may cause hazards.
18. Do not use outdoors.
19. Do not let cord hang over edge of table or counter, or touch hot surfaces.
10. Keep hands and utensils out of container while blending to prevent the possibility of severe
personal injury and/or damage to the blender. A rubber scraper may be used but must be
used only when the blender is not running.
11. Blades are sharp. Handle carefully.
12. Always operate blender with cover in place.
13. When blending hot liquids, completely remove the stopper in the cover before turning on the
blender. See Hot Blending Instructions.
SAVE THESE INSTRUCTIONS
Specifications
❍Capacity: 4 Litre Working Capacity
❍Switch Setting: (3 speeds) POWER ON/OFF STOP LOW MED HIGH PULSE
❍Revolutions Per Minute: 15,800 18,000 20,800 20,800
(free running-approximate)
❍Rating: 120 Volts-60HZ-Single Phase AC -15.0 Amps. U.S. models only.
230 Volts-50HZ-Single Phase AC -1500 Watts.
❍Base: Die-cast – grey coating
❍Container: Stainless steel with stainless steel blades - clear polycarbonate
clamp-on lid, with gasket and stopper.
❍Bearing: High performance ball bearing.
❍Cord: 7 foot (2.44 m) - 3-conductor ground cord with strain relief in base.
❍Overall Height: 26 inches (66 cm).
❍Weight: 38 pounds (17.2 kg) net - Shipping Weight 41 pounds (18.6 kg).
❍UL, NSF, CSA Listed (120 volts ONLY).
❍Timer: Some models have a timer, adjustable from 10 seconds to 3 minutes
for automatic blending.
❍Operating Cycle: 3 min ON/1 min OFF

GROUNDING INSTRUCTIONS
For your protection, this appliance is equipped with a 3-conductor cordset.
120 Volt units are supplied with a molded 3-prong grounding-type plug (NEMA 5-15P) and should
be used in combination with a properly connected grounding type outlet as shown in Figure A.
If a grounding type outlet is not available, an adapter, shown in Figure B, may be utilized to enable
a 2-slot wall outlet to be used with a 3-prong plug except in Canada and Europe.
Referring to Figure C, the adapter must be grounded by attaching its grounding lug under the screw
of the outlet cover plate.
Caution: Before using an adapter, it must be determined that the outlet cover plate screw is
properly grounded. If in doubt, consult a licensed electrician. Never use an adapter unless you
are sure it is properly grounded.
Note: Use of an adapter is not permitted in Canada and Europe.
Green/Yellow: Earth Ground • Blue: Neutral • Brown: Live
Note: User installed cord set plugs are not permitted in Europe.
Operation
1. Before starting, make sure that the blender cord is
unplugged.
2. Place container assembly on motor base so that it is
firmly seated and not tilting to one side. Plug in blender
cord into outlet.
3. Put ingredients into container and cover it. Always add
liquid ingredients first, unless otherwise specified in
recipe. Do not fill above Max line.
4. Press the Power button to turn on the blender.
Green LED will illuminate.
For continuous operation, press either the LOW , MED , or HIGH button.
When finished blending, press STOP . For momentary operation, press the
Pulse button ; motor will run on HIGH speed until the button is released.
Note: Your CB15/CB15T utilizes a Slow Start™feature. When pressing MED or HIGH, the unit
will start in the LOW position for 1 second and then switch to the setting selected. This allows
for a more even blending of ingredients in container.
5a. Always hold container with one hand when starting and while blending. Never operate without
jar lid properly clamped in place.
5b. FOR BLENDERS WITH A TIMER (CB15T)
1. Press the Power button to turn on the blender. Press the UP arrow or DOWN arrow.
The initial time will be 10 seconds.
2. Push the UP arrow to set the time required. The timer will only advance in
10-second intervals. Timer can be set to the maximum of 3 minutes.
00:10
Circuit Grounding
Connected Properly
Grounding Prong
Grounding Plug
Adapter
Cover
Mounting
Screw
Cover of Grounded Outlet Box
A. B. C.

3. Select and press a speed button; the blender will start and run for that selected time. It will
count down in 1-second intervals and stop at 0. NOTE: If you want to increase or decrease
time while timer is counting down, press UP or DOWN arrows. Timer will increase or decrease
in 10-second intervals. After 5 seconds the timer will turn "Off" and return to manual mode.
4. When using the timer again, the initial time will be the last time set.
NOTE: If unit has been unplugged, the timer will default back to 10 seconds.
6. Allow motor to come to a complete stop before removing container. Never place
the container on the motor base or remove it from the motor base while the motor
is running.
7. Press the POWER button again to turn off the blender.
8. Remove the container from the motor base and empty the contents.
9. Wash and dry container after each use. See separate Cleaning & Sanitizing Instructions
for All MRC Blenders.
10. Not For Waterjet Cleaning.
11. The use of ear protection is recommended during extended operating periods.
TO REALIZE MAXIMUM SERVICE LIFE, OBSERVE THE FOLLOWING PRECAUTIONS:
1. Do not lubricate container bearing, drive shaft, or shaft seals. These parts are lubricated
and sealed at the factory and do not require any further lubrication.
2. Reduce amounts of material processed to less than the full 4-liter capacity when working with
viscous or fibrous materials.
3. When cleaning exterior of container, keep it in normal upright operating position to prevent
liquids from running into the bearing through the bottom end.
Hot Blending Instructions: Important!
To minimize the possibility of scalding when blending hot materials, the following
precautions and procedures must be observed:
• Hot materials are those which are 100˚F (38˚C) or hotter.
• If you are using the standard container lid that originally came with your blender, limit
the amount of material processed to one (1) litre and completely remove the stopper in
the lid before turning on blender. This will allow venting of the rapidly heated and
expanding air present inside container when blender is running.
• Always start blending on lowest speed setting, then progress to desired speed.
• Never stand directly over blender when it is being started or while it is running.
• Constant monitoring of the condition of the container lid gasket and the container lid
clamps is mandatory. Replace these parts if they become worn or loose, or are damaged
in any way.
Note: A special accessory Hot Blending Lid assembly is available which allows safe
processing of larger loads. Order: One-Gallon Hot Blending Lid, Catalog No. CBL-10. If you
are using the special accessory Hot Blending Lid, follow the instructions packed with the lid.
BEFORE PROCEEDING WITH HOT BLENDING, PLEASE REREAD ALL INSTRUCTIONS
IN THIS OPERATING MANUAL.
Maintenance
Motor - Not For Waterjet Cleaning
The MRC Commercial Blender ball bearing motor requires no greasing or oiling. Sealed-in
lubrication provides smooth unit operation.
Container - The stainless steel container can be sterilized without injury to the bearing.
Jar pad to be washed and rinsed in solutions noted in Cleaning and Sanitizing Instructions.

Depending on the operating conditions, service life of the main components of the container blade
assembly, socket head shaft and shaft seals is 500 hours actual running time.
When any one of these main components has worn to the extent that replacement is required, it is likely
that the other components will need to be replaced also. It is therefore recommended that container
blade assemblies be replaced as a unit.
Die-cast lock nut must be tightened securely (65-70 foot-pounds torque) when reassembling
container.
Power Supply Cord - The power supply cord should not be replaced by the end user. The power supply
cord should only be replaced by the manufacturer’s authorized importer (or, in the United States and
Canada, by an authorized service center).
Note: All parts require constant monitoring for conditions requiring replacement. For assistance, contact
your nearest Service Center.
Limited One Year Warranty
MRC warrants every new MRC Commercial Blender to be free from defects in material and
workmanship for a period of one year from the date of purchase when used with foodstuffs, nonabrasive
liquids (other than detergents) and nonabrasive semiliquids, providing it has not been subject to loads
in excess of the indicated rating. In addition, the motor in this appliance has a full three year warranty.
Under this warranty, the MRC Commercial Division will repair or replace any part which, upon our
examination, is defective in materials or workmanship, provided the product is delivered prepaid to
the MRC Service Center at: 314 Ella T. Grasso Ave. Torrington, CT 06790, or any Factory Approved
Service Center.
This warranty does not: a) apply to any product which has become worn, defective, damaged or
broken due to use or due to repairs or servicing by other than the MRC Service Center or a Factory
Approved Service Center or due to abuse, misuse, overloading or tampering; or b) cover incidental or
consequential damages of any kind.
The one year warranty is applicable only to appliances used in the United States or Canada; this
supersedes all other express product warranty or warranty statements. For MRC products sold
outside of the U.S. and Canada, the warranty is the responsibility of the local importer or distributor.
This warranty may vary according to local regulations.
Warning: This warranty is void if appliance is used on Direct Current (D.C.)
Service
Note: If your application involves the processing of biologically active materials, any items returned
for service must be sterilized before being shipped. Such items must be clearly identified as having
been sterilized, both by a tag on the item itself and by a statement in the accompanying
correspondence. MRC will not accept delivery of any returns unless they are so identified.