MSTR BRAND Sonance Elura Blue Label Series User manual

Congratulations and thanks for your selection of the Elura Blue Label Series speakers by Sonance®. These products
have been designed for easy installation and reliable performance. Because you’re a professional in this eld, we’ve
limited the following installation guidelines to essential facts and recommendations.
One thing to keep in mind: Elura is committed to your success. Any questions, comments or assistance you require
is available anytime by contacting us directly. Thanks for your support.
PRE-INSPECTION
Check the contents of each carton to make sure no damage has occurred during transit or handling. Let us know
immediately if anything appears to be damaged.
SELECTING SPEAKER LOCATIONS
Take your usual care when selecting speaker locations and placement. Avoid wiring, plumbing, lighting xtures
and HVAC ducting. Speaker wiring should already be in position for new construction – just watch for studs and
joists when making your cut-outs.
Depending on room size it is best to place speakers approximately 12’ from one another. Proper spacing will
improve sound imaging. Consider the room environment and furniture placement while selecting your primary
listening area.
SPEAKER INSTALLATION
We package the Blue Label Series with the grille on to prevent possible damage. You’ll nd the paint mask and
adhesive chips to attach the mask are packaged adjacent to the speakers. Position the dog ears ush with the
bae frame and hold next to your cut-out.
Connect the speaker wires (+ to + / - to -), install the speakers and connect to the amplier. For multiple speakers,
be sure to check impedance matching.
PAINT PROCEDURES
You may have your own painting methods but we recommend the speakers be painted in place using the paint
guard (included). Paint the grilles in a separate location (not installed on the speaker). First gently remove the
lightly glued Dacron, and take care to not clog the holes with paint. Carefully re-install Dacron and grilles for a
tight attractive nish. Install the grille ush with the bae edge on all sides and you’re set.
BASIC LEVEL CONTROL ADJUSTMENT
Most Blue Label speaker models include individual woofer and tweeter SPL (volume) controls so you can adjust the
balance of low and high frequencies to best suit your individual listening area. We recommend setting the tweeter
levels rst and then match them with the desired bass level.
If you are connecting more than one pair of speakers to your amplier, we suggest using the lower bass SPL
position until you conrm your amplier can handle the additional power requirement.
Owner’s Manual / Installation Guide

HIGH FREQUENCY ADJUSTMENT
Since high frequencies are directional, almost all Blue Label speaker models are equipped with adjustable, pivoting
tweeters. While taking care not to touch the speaker cones, rotate the tweeter toward the primary listening area.
Once you have the tweeters positioned and speaker volume adjusted to your preference, replace the grille securely
so it is ush with the surrounding trim ring and enjoy!
PRODUCT WARRANTY
Elura speaker products are guaranteed to meet or exceed the specifications included in this manual and carry with
them a 2 year limited lifetime warranty under normal conditions of use. This warranty covers free parts and labor
on all components with the obligation that Elura will repair or replace any component found defective in materials
or workmanship. This warranty does not apply to products that have been abused, incorrectly installed, modified,
disassembled and/or repaired by anyone other than Elura or our appointed repair facility. Products qualified under
this warranty must be returned to the factory or a service center designated by Elura, with all transportation and
insurance charges pre-paid.
SPEAKER SPECIFICATIONS
S6.5LCR
Speaker Type: In-ceiling LCR, Zero Bezel Woofer: 6.5” CarbonX Cone, Silhouette Surround
Tweeter: 1” XL Chambered Silk Dome, Pivoting Power: 5-130 watts
Impedance: 8 ohms Freq. Response: 45Hz-20KHz
Sensitivity: 91dB EQ Adjustments: Contour Switch with -3, 0, +3
Finish Dimensions: Ø9.27” (235mm), 4.90” (125mm) Cutout Dimension: Ø8.25”(210mm)
S6.5LCRIW
Speaker Type: In-wall LCR, Zero Bezel Woofer: Dual 6.5” CarbonX Cone, Silhouette Surround
Tweeter: 1” XL Chambered Silk Dome Power: 5-130 watts
Impedance: 6 ohms Freq. Response: 45Hz-20KHz
Sensitivity: 91dB EQ Adjustments: Contour Switch with -3, 0, +3
Finish Dimensions: 7.87” (200mm), 15.57“ (395mm), 3.47” (88mm)
Cutout Dimension: 6.89”(210mm), 14.57” (370mm)
S8LCR
Speaker Type: In-ceiling LCR, Zero Bezel Woofer: 8” CarbonX Cone, Silhouette Surround
Tweeter: 1” XL Chambered Silk Dome, Pivoting Power: 5-130 watts
Impedance: 8 ohms Freq. Response: 45Hz-20KHz
Sensitivity: 91dB EQ Adjustments: Contour Switch with -3, 0, +3
Finish Dimensions: Ø11.17” (284mm), 5.70” (145mm) Cutout Dimension: Ø10.08”(256mm)