Mthtrains Premier 20-91064 User manual

The Premier Center Copula Steel Caboose offers

a new level of excitement and realism for your

O or O-27 Gauge model railroad. Constructed

from sturdy ABS plastic, the Center Copula Steel

Caboose was created from quality components

and has been designed for years of operation.

The Premier Center Copula Steel Caboose

comes fully assembled, decorated and ready for

use right out of the box. The Center Copula

Steel Caboose features an illuminated interior

controlled from track power. Use and operation

is made easy by following the instructions on

the following pages.

Caboose

Center Copula Steel

There will be two spots of hot

glue holding the LEDs in place.

Use a screw driver to loosen the

wires from the spots of glue. Pull

the LEDs back towards the

inside of the shell to remove

them. Replace the LEDs with a

new set and use hot glue to put

the wires back in place. Plug the

wires back into the connector

under the interior. Reassemble.

Note: When reassembling, the

end posts of the shell must pass

through the corresponding holes

in the interior.

STEP

77End Posts of

the Shell

Wires Should

Be Tucked

Behind These

Clips Upon

Re-assembly

LIMITED ONE-YEAR WARRANTY

All M.T.H. products purchased from an Authorized M.T.H. Train

Merchant are covered by this warranty.

See our Website at or call 1-888-640-3700 to

identify an Authorized M.T.H. Train Merchant near you.

MTH products are warrantied for one year from the date of purchase against

defects in material or workmanship, excluding light bulbs and traction tires.

We will repair or replace (at our option) the defective part without charge

for the parts or labor, if the item is returned to MTH Electric Trains, Inc.

within one year of the original date of purchase. This warranty does not

cover damages caused by improper care, handling, or use. Transportation

costs incurred by the customer are not covered under this warranty.

Items sent for repair must be accompanied by a return authorization

number, a description of the problem, and the original sales receipt from

an Authorized M.T.H. Train Merchant, which gives the date of purchase.

Call 410-381-2580, fax 410-423-0009, or e-mail the Service Department at

to obtain a return authorization number.

This warranty gives you specific legal rights, and you may have other rights

that vary from state to state.

Service Department

M.T.H. Electric Trains, Inc.

7020 Gateway Drive

Columbia MD 21046-1532

www.mth-railking.com

[email protected]

M.T.H.

ELECTRIC TRAINS, INC.

7020 Columbia Gateway Drive

Columbia, MD 21046-1532

www.mth-railking.com

Turn the caboose

upside down and

unplug the red

LED's from

underneath the

interior.

STEP

INSTRUCTIONS To replace the interior light bulbs, follow these steps. 1) To remove the shell from chassis remove the four screws located

underneath the trucks. 2) With the four screws removed, lower the chassis from the shell, take care not to pull the wires out.

3) To be able to separate the interior from the shell you need to remove the step platform from both ends. In order to do this

you need to loosen the end frames from the step platform. You must do this carefully so that you don't break them. Grasp

the end frame by the bottom and pivot outwards 5 With the step platforms removed you can then lower the

interior down from the shell (to completely remove the body from the interior, goto step 6. 5) You can now replace the bulbs by pushing the socket up from the

bulb holder and pull the bulb from its socket. Replace with a new one, and reverse the steps to reassemble the caboose. To replace the two red LED lights at

the ends of the caboose follow steps 1- 4, 6 and 7 on the back page.

°. You can then remove the step platforms. 4)

Remove these

four screws