MTX CXP10 User manual

CHEVY EXTRA CAB
And GMC Extra Cab & 3-Door Models
Warranty Statement
ThunderForm Loaded Enclosures purchased in the United States from an authorized MTX dealer
are guaranteed against defects in material and workmanship for a period of two years from the date
purchased by the end user, and limited to the original retail purchaser of the product.
Amplified ThunderForm Enclosures purchased in the United States from an authorized MTX dealer
are guaranteed against defects in material and workmanship for a period of one year from the date
purchased by the end user, and limited to the original retail purchaser of the product.
Product found to be defective during that period will be repaired or replaced by MTX at no charge.
This warranty is void if it is determined that unauthorized parties have attempted repairs or altera-
tions of any nature. Warranty does not extend to cosmetics or finish. Before presuming a defect is
present in the product, be certain that all related equipment and wiring is functioning properly. MTX
disclaims any liability for other incurred damages resulting from product defects. Any expenses
incurred in the removal and reinstallation of products are not covered by this warranty. MTX's total
liability will not exceed the purchase price of the product. If a defect is present, your authorized MTX
dealer may be able to effect repairs.
Proof of purchase is required when requesting service, so please retain your sales receipt and take
a moment to register your product online at www.mtx.com.
21A
7
238
Vehicle Specific Subwoofer Enclosure
Made in the USA
One Mitek Plaza, Winslow, IL. 61089
1-800-225-5689
www.mtx.com

READ ALL DIRECTIONS CAREFULLY BEFORE BEGINNING
MOUNTING LOCATION:
The enclosure mounts on the driver’s side
under rear seat on Chevy Extended Cab Trucks.
TOOLS REQUIRED FOR INSTALLATION:
Powered Screwdriver #2 Phillips Head Bit
Wire Cutters T-50 Torx
5/16” Wrench Terminal Crimpers
6” Bit Holder Extension 7mm Nut Driver
INSTALLATION:
Follow the steps below
1
.
Place enclosure under rear seat, with woofer firing down (do not
mount yet).
Rear Seat
Enclosure
2
.
If externally amplified make speaker connections to the enclosure
from the amplifier; loosen terminal knobs (a 13-mm nut driver can be
used). Connect speaker wires from amplifier to enclosure, positive to red
terminal knob and negative to black terminal knob. Refer to step
19
and
2
0
for mounting directions.
AMPLIFIED THUNDERFORM
Routing Power Wire; we recommend a connection directly to the
battery.
3
.
Remove driver side threshold trim; remove three phillips head screws
and pull up on trim, it will remove easily.
Mounting Brackets
For technical assistance call 1-800-CALL MTX.
These instructions are guidelines only and in no way are intended to
replace a professional installation. As always before screwing or drilling
check to make sure you will not damage any wires or hoses or cause
damage to the vehicle.
Warning:
Batteries normally produce explosive gases which can cause
Warning: Batteries normally produce explosive gases which can cause Warning:
personal injury. Therefore, do not allow flames, sparks or lighted sub-
stances to come near the battery. When charging or working near a
battery, always shield your face and protect your eyes. Always provide
ventilation.
Conventional Wiring of Aftermarket Radio
_
_
+
20 Amp Fuse
Lo
w Le
ve
l Signal
Tu
rn
On Lead
S
TATU
S
Optional EBC
(Electronic Bass Control)
1
6

4
.
Using furnished wiring harness route 10ga red power wire starting
at pre-amp location. Route wire under rear seat on driver's side, over to
threshold and under carpet to the front of vehicle.
5
.
Open hood.
6
.
Drill a hole through the firewall. Locate a spot low on the firewall on the
driver’s side. You should always look to find a clear path. Drill a hole from
inside of the vehicle into engine compartment and insert grommet.
Fire
wa
ll
Batte
ry
Dr
ill Hole
fo
r Grommet
Note: To avoid any damage to parts inside engine compartment,
drill from inside of vehicle using a short bit.
7
.
Route 10ga red power wire through grommet into the engine compart-
ment.
8
.
Route 10ga red power wire through engine compartment safely away
from any moving or hot parts that could damage the wire.
9
.
Cut 10ga red power wire to length, connect the supplied fuse holder
from the wire kit to the end of the wire.
Optional
- The EBC, or Electronic Bass Control, allows a remote bass
control to be adjusted from the driver's seat.
Setting Crossover
You should set the crossover to your own personal listening taste. The
crossover is adjustable to any frequency between 50Hz (counterclock-
wise) to 150Hz (clockwise). As a guideline, the goal is to create the illu-
sion of bass up front. The higher the crossover point the more “audibly
visible” your sub is going to be. Take your time and really listen to your
system, grab a soda and a few of your favorite tunes and have fun.
T
ROUBLESHOOTING TIPS IF AMP DOES NOT TURN ON
Check all connections at battery and that fuse is installed
Check speaker wire connections
Check ground
Check fuse on pre-amp
18
.
Reinstall threshold trim. Locate and align holes in vehicle with pins
on trim; secure with the three phillips head screws removed earlier.
19
.
Using hardware provided, attach the mounting brackets to the enclo-
sure as shown below. If installing in a 1999 or
newer
model, add rubber
foot as shown below.
1999 or Ne
we
r
2
0
.
Using screws provided, install the enclosure into vehicle as shown
below.
2
5

1
0
.
Remove
20
amp fuse from MTX fuse holder. Connect furnished ring
terminal to positive side of battery. Remove 5/16" bolt from factory battery
terminal. Pass bolt through factory battery terminal, then ring terminal,
and into the other side of factory battery terminal and retighten bolt.
1
1
.
Ground amplifier to chassis of vehicle; connect the terminal provided
to the 10ga black wire from furnished wiring harness. A good ground is
as important as the power connection. The ground should be as short as
possible and the contact point should be free of paint and debris.
S
PEAKER WIRES
1
2
.
In the channel on drivers' side threshold locate the rear speaker
wires located in the smaller of the two wiring harnesses. Colors are right
channel; dark blue (positive) light blue (negative), and left channel; brown
(positive), yellow (negative). Tap into wires
with the supplied RCA High
Level input wires
and route under carpet to the rear seat, over to pre-amp
on enclosure. Depending on the option package, there may be more than
one wire in these colors. The speaker wire will be the smallest wire.
Although, MTX has made every effort to assure proper wiring colors,
MTX is not responsible for any changes made by the vehicle manufac-
turer which sometime occur. If wiring colors do not match then physical
verification is required.
C
ONNECTION TO ENCLOSURE
1
3
.
Connect speaker wire
RCA's to the
inputs of pre-amp.
Note: Patented BTL turn on circuitry- amplifier senses DC offset provided by “high
powered” or BTL type head units. This feature turns the amplifier on automatically
if you are using high level inputs.
_+
20 Amp Fuse
20A
PWRGNDRE M
EBC
INP U T
RIG H TLEF T
GAINX-OVER
STATUS
STRIPED
SOLID
SOLID Dark Blue (+)
Light Blue (-)
Yellow (-)
Brown (+)
Optional EBC
(Electronic Bass Control)
1
4
.
Plug power wire harness into amplifier pre-amp.
2 0
A
P W
R
G N
D
REM
E B
C
INPUT
RIGH
T
LEF
T
GAIN
X-OVER
STATU
S
1
5
.
Replace
20
amp fuse under hood.
1
6
.
When amp turns on, LED will display red during diagnostic mode,
and then green, signaling amp is on and functioning. Amp will only turn
on when radio is on.
1
7
.
Adjust gain and crossover.
Setting Gain
Turn gain knob on Thunderform pre-amp to minimum, counter clock-
wise. Play a favorite tape or compact disc that contains consistent music
and bass. Turn the source unit to maximum listening level. You should
know that some source units will produce distortion or “clip” before the
unit reaches maximum volume. Reduce volume to the loudest listening
level before distortion. Turn the gain knob on the Thunderform pre-amp
clockwise until the speaker starts to distort and reduce gain to loudest
listening level before distortion.
3
4