MTX RZRXP-10 User manual

MTX.COM
OWNER’S MANUAL
RZRXP-10
POLARIS®RZR®AMPLIFIED SUBWOOFER ENCLOSURE

MTX.COM
2
IMPORTANT NOTICE
If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support
at 1-800-225-5689.
When connecting power and ground wires ensure that the red power wire is fused at the point
where it is connected to the vehicle’s battery. Failure to do so can result in damage to the vehicle if a
short circuit develops between the vehicle connection point and the product.
PRODUCT INFORMATION
Model #
Serial #
Dealer’s Name
Date of Purchase
IN THE BOX
• RZRXP-10AmpliedSubwooferEnclosure
• EBCandEBCExtensionWire
• Mounting Hardware
  (1)1"T30TorxScrew
  (2)1.5"T30TorxScrews
ADDITIONAL ACCESSORIES NEEDED AND NOT INCLUDED
MTX recommends using StreetWires PS1K-10 amp kit which includes the following:
• PowerandGroundWiretoRuntotheBattery
• 20AATCFuseHolderandFuse
• AccessoryConnectionWire
• RCACablestoConnecttotheSource
INSTALLATION TOOLS
The following is a list of suggested tools needed for installation:
• Torx-T40
• Torx-T30
• Torx-T25
• 10mm Wrench or Socket
• Razor Knife
INTRODUCTION
ThankyouforpurchasingtheMTXAudioampliedsubwooferenclosuredesignedforthePolaris®
RZR®.TheeasytoinstallsubwooferistheperfectdirecttbasssolutionforyourPolaris®RZR®.
CongratulationsandenjoytheultimateaudioexperiencewithMTX!
FITS THE FOLLOWING VEHICLES
• RZR®XP/XP41000(2014andUp)
• RZR®XP/XP4TURBO(2016andUp)
• RZR®900/900S/1000S(2015andUp)
• RZR®4900EPS(2015andUp)
NOTE:Willnottonvehicleswiththeaddedheateraccessory.

MTX.COM 3
FEATURES
• 10"All-WeatherAmpliedSubwooferEnclosure
• Integrated250-WattRMS/500-WattPeakPowerAmplier
• IntegratedPowerandGroundConnections
• LowLevelInputwithExternalGainControl
• DashMountBassControlKnob(Included)
• MountsUnderneathDashboard-DirectFit,NoDrillingRequired
SPECIFICATIONS
• RMS Power Handling: 250-Watts
• Peak Power Handling: 500-Watts
• FrequencyResponse:34Hz-120Hz

MTX.COM
4
INSTALLATION
Step 1 - Release the two quick locks to remove the hood from the vehicle.
Step 2 - Lift up the hood and slide towards the front of the vehicle.
Step3-Removethetwo(2)T40screwsholdingdownthetopdashcover.

MTX.COM 5
Step4-Liftandpullbackthetopdashcovertoreleasetheclipsholdingitinplace.Unplugthegauge
and switches making sure not to damage the vehicle and ignition wiring. Make note to remember
whatconnectorisassociatedwitheachspecicswitch.
Step5-RemovetheTorxheadscrewfromthedashpocketbrace.Afterthisisremovedtheplastic
dash pocket and bracket can be pulled out of the dash.

MTX.COM
6
Step6-Removethetwo(2)T40screwsholdingthedashboardinplace.
Step 7 - Pull the dashboard towards the back of the vehicle. There are locking clips on the right and
left side that hold it in place. The dash will pop out.

MTX.COM 7
Step 8 - Carefullylift the dash out of the vehicle. If the locking clips have fallen off, place them back
onto the locking tabs on the dash. These are needed to re-assemble the dashboard.
Step9-Removethetwo(2)10mmhexboltsthatareholdingthegloveboxtothevehicleframe.When
thescrewsareremovedthegloveboxcanbelowereddownandoutoftheenclosure.
Step10-Removetheve(5)T25screwsholdingthegloveboxtogether.Thegloveboxwillthenopen
like a book.

MTX.COM
8
Step11-Cutthe“binding”plastichingewitharazorknifetoseparatethefrontandbackoftheglove
box.Thebacksideofthegloveboxwillnolongerbeused.Thefrontsideofthegloveboxwillbe
attached to the enclosure.
Step12-Usingtheve(5)T25screwsthatwereremovedfromthefront/backassemblyoftheglove
box,attachthefrontofthegloveboxtotheRZRXP-10enclosure.Takecaretonotstripouttheplastic,
buttightenitenoughsothegasketsealsbetweentheenclosureandglovebox.
Step 13 - The enclosure can now be placed into the vehicle. Place the rectangular protrusion at an
angleintothedasharearst.Theenclosurecantheneasilyslideupintoplace.

MTX.COM 9
Step14-Holdtheenclosureupandalignthegloveboxscrewholeswiththevehicleframemount.
Replacethetwo(2)10mmhexboltsandtightentheenclosureinplace.Itmayhelptoplacea
supportingobjectundertheenclosuresobothhandsarefreetolineupthescrewholeswiththe
vehicle frame mount.
Step 15 - There are three mounting holes on the bottom of the enclosure to screw the base of
the enclosure into place. The furthest hole to the right uses the included 1" screw. The other two
mounting holes use the 1.5" screws. Tighten the screws down, but take care to not strip them. These
screws lock into the plastic foot board.

MTX.COM
10
Step 16 - Now that the enclosure is securely tightened in place, the power and signal wires need to
be connected to the battery and signal source.
• The Red wire should be connected directly to the battery’s positive terminal and fused with a
20A fuse.
• The Blackwireshouldbedirectlyconnectedtothebattery’snegativeterminal.
• If your vehicle is equipped with the Polaris®bussbarkit,theRedandBlackwirescanbe
  connectedtothebussbarunderthehoodontherewall.TheRedwirewillstillneedtobe 
fused.
• The BluewirecanbeconnectedtotheACC/KeyTurnOnlocatedonthebussbarofanyvehicle.
Step17-ConnecttheRCAinputstothesignalsourceofyourchoice
Step 18 - Turn the unit on and check to make sure everything works. Set the gain using the gain pot
that is attached to the orange / grey wires. Set the gain to the bass level desired.
Step19-TheincludedEBCcanbeconnectedandmountedtoadesiredlocationtoalloweasytrim
adjustmentofthebasslevelafterthegainhasbeenset.
Step 20 - Replace all the parts and screws that have been removed to return the RZR back to its
completely assembled state.