Mueller H-17800 User manual
Mueller®H-17800 Abandonment Plug
INSTALLATION FOR D5 / DH5 DRILLING MACHINES
1. Attach the machine adapter to the
D5 / DH5 then extend the boring bar
and attach the Boring Bar Adapter.
Reference Machine Stack Up
Reference Table at end of instructions
for stack up and part numbers.
2. Using the stem in the H-17800,
shut off ow to the tee by turning the
Operating Head clockwise until the
stem seats at the bottom of the tee.
3. Remove the Operating Head from
the stem.
4. Carefully remove the Cap ensuring
not to unseat the stem.
5. Attach Extracting Tool to H-17800
tee stem.
6. Install the Reducing Bushing onto
the tee.
7. Install the Control Valve onto
Reducing Bushing. Ensure Control
Valve is in open position for stem
extraction.
8. Attach Machine Adapter to the
Control Valve.
9. Slowly advance boring bar until
boring bar adapter engages the
extracting tool and rotate counter-
clockwise. Once the Boring Bar
Adapter is fully threaded onto the
Extracting Tool, continue rotating
counter-clockwise until the stem is
disengaged from the tee.
10. Pull boring bar until stem clears
the Control Valve.
11. Close Control Valve and release
the pressure with the bypass valve
(only on H-10917).
INSTALLATION INSTRUCTIONS
12. Remove machine from Control
Valve. Remove stem, Extracting Tool,
and Boring Bar Adapter from machine.
STEM REMOVAL
Reliable Connections
TM
Gas (North America)
1.800.798.3131
www.muellergas.com
International
1.423.490.9555
www.mueller-international.com
[email protected] Form 13899 – Rev 07/18
Operating Head
Cap
1. With the Machine Adapter still
connected to the D5 / DH5, extend the
boring bar and attach the Boring Bar
Adapter.
2. Attach Inserting Tool onto boring
bar. Then attach Completion Plug onto
Inserting Tool.
3. Attach Machine Adapter onto
Control Valve.
4. Shift the bypass valve on the
Control Valve (only on the H-10917) to
equalize the pressure on both sides.
5. Open Control Valve and ease
boring bar down until Completion Plug
engages treads of tee.
6. Thread Completion Plug into tee in
aclockwise rotation until plug is fully
engaged and sealed onto the surface
of the tee.
7. Turn boring bar in a counter-
clockwise direction to disengage
Boring Bar Adapter from Inserting Tool.
8. After Boring Bar Adapter is free
from Inserting Tool, pull the boring bar
and Inserting Tool past the Control
Valve and close it.
9. Using the bypass valve on the
Control Valve release the pressure.
10. The D5 / DH5 can be removed
from Control Valve.
11. Remove Control Valve and Hex
Bushing from tee.
12. Attach Abandonment Cap onto tee
over completion plug.
13. Weld abandonment cap to tee.
COMPLETION PLUG INSERTION
Mueller®H-17800 Abandonment Plug
INSTALLATION FOR D5 / DH5 DRILLING MACHINES
D5 / DH5 MACHINE STACK UP
Reliable Connections
TM
Copyright © 2018 Mueller Co., LLC. All Rights Reserved.
The trademarks, logos and service marks displayed in this document herein are the property of Mueller Co., LLC, its afliates
or other third parties. Products marked with a section symbol ( § ) are subject to patents or patent applications. For details, visit
www.mwppat.com. Please contact your Mueller Sales or Customer Service Representative concerning any other application(s).
D5 / DH5
Machine
Adapter
Control Valve
Reducing Bushing
1" H-17800 11/4" H-17800 2" H-17800
Abandonment Plug 538565 538566 538567
Reducing Bushing 313328 313329 313330
Control Valve H-10914 or H-10914, H-10917 H-10914, H-10917
H-10918* or H-10918 or H-10918**
Machine Adapter 036196 036188 036975
Boring Bar Adapter 036198 - -
Extracting Tool 088279 088286 081499
Boring Bar Adapter 040438 036324 040438
Inserting Tool 083256 083261 083400
Completion Plug 538565 538566 538567
Abandonment Cap 538296 538297 538298
*Cannot use the H-10917 for this size.
**When using the H-10918 a special machine adapter is required (538568).
