Multibor Beauty Suite User manual

PROFESSIONAL TOOLS
Before getting started, please read this User Guide carefully.
Attention! The device has sucient means of electronic protection,
but no automation is able to provide 100% safety against unjustied,
inept or destructive steps by the User.
Please remember! Before you switch on the rotation, make sure that
nothing stands in its way, the engine is free, there is a tool in the
collet clamp, the collet clamp is locked, and the collet holds the tool
rmly.
Caution! Mechanical defects in the entire device or in separate parts
thereof and absence of its components as well as damaged or burnt
engine or its power cable shall deprive the User of the opportunity of
free repair and shall not impose any warranty obligations upon the
Manufacturer.
Please handle the device with due care and use it as prescribed. Do
not allow for excessive workload and do not use it for operations the
device is not intended for, and it will then serve you very well for
years!
Should you have any questions regarding the use of the device or
should you put the device into such modes of operation where from
you don't know the way out, please contact the Service Center.
Service Center
www.multibor.eu
2
Natural
nails
Gel & Acryl
Pedicure
MULTIBOR
Pedicure Bits
Name ToolType Display
Multibor - Beauty Suite :: Program Control
“127B” “90B”Final foot polish
“50R” “50G”
Removing of coms
and rouche skin on toes
“b100R” “b100G” “b100B”
On the edge of step
cracks treatment
“127R” “127G”
Very rough heels
primary treatment
Abrasive, max 9mmfor Toes abrading
Abrasive or Silicone, max 13mmThe step`s skin grinding
Silicone, max 10mmThe natural nail polishing
Diamond, max 5mmNail Art
Carbide cone, max 3mmCorrection of the inside nail
Diamond disc, max 5mmFree edge of the nail simulation
Carbide, max 7mmGel and Acryl correction
Diamond point,
max 3.3mm
Sawing in the cuticle zone
Mounted natural Bus, max 25mmThe natural nail polishing
Diamond disc, max 5mmFree edge of the nail
Diamond cylinder, max 5mmLateral nail folds
Diamond tapered cylinder, max 5mmRemoval of cuticle

Introduction
Multibor — Beauty Suite is a series of devices from the Beauty lineup
developed under the Multibor-Suite technology intended for
intensive operation with signicant workloads while providing the
entire range of services in the elds of machine-assisted manicure and
pedicure as well as for incrementing, modeling, and correction of
articial nails.
The lineup of devices comprises the following models:
• Multibor – Beauty PRO
• Multibor – Beauty STYLE
• Multibor –Beauty EXTRA
These models have dierent technical properties and congurations.
Multibor — Beauty Suite is a milling cutter for masters of nail care
(hereinafter, the 'Milling Cutter'). This is a microprocessor unit with
separate programs for dierent types of operations and for dierent
types of tools with automatic selection of preset programs and with
digital adjustment for optimal mode of operation.
3
PROFESSIONAL TOOLS
Before getting started, please read this User Guide carefully.
Attention! The device has sucient means of electronic protection,
but no automation is able to provide 100% safety against unjustied,
inept or destructive steps by the User.
Please remember! Before you switch on the rotation, make sure that
nothing stands in its way, the engine is free, there is a tool in the
collet clamp, the collet clamp is locked, and the collet holds the tool
rmly.
Caution! Mechanical defects in the entire device or in separate parts
thereof and absence of its components as well as damaged or burnt
engine or its power cable shall deprive the User of the opportunity of
free repair and shall not impose any warranty obligations upon the
Manufacturer.
Please handle the device with due care and use it as prescribed. Do
not allow for excessive workload and do not use it for operations the
device is not intended for, and it will then serve you very well for
years!
Should you have any questions regarding the use of the device or
should you put the device into such modes of operation where from
you don't know the way out, please contact the Service Center.
Service Center
www.multibor.eu

Delivery Set
· Power unit
· Handheld milling cutter (micromotor)
· Micromotor pad
· Pedal (available in specic models)
· User Guide
· Packaging
4
Introduction
Multibor — Beauty Suite is a series of devices from the Beauty lineup
developed under the Multibor-Suite technology intended for
intensive operation with signicant workloads while providing the
entire range of services in the elds of machine-assisted manicure and
pedicure as well as for incrementing, modeling, and correction of
articial nails.
The lineup of devices comprises the following models:
• Multibor – Beauty PRO
• Multibor – Beauty STYLE
• Multibor –Beauty EXTRA
These models have dierent technical properties and congurations.
Multibor — Beauty Suite is a milling cutter for masters of nail care
(hereinafter, the 'Milling Cutter'). This is a microprocessor unit with
separate programs for dierent types of operations and for dierent
types of tools with automatic selection of preset programs and with
digital adjustment for optimal mode of operation.

ATTENTION! Disregarding these safety precautions may damage
the Milling Cutter or may result in its ignition or in electric shock for
you.
ATTENTION! Plug the Milling Cutter in the electric mains thru
standard three-pin sockets with grounded terminals only.
Nine Simple Rules:
1. Never use electric mains where voltage and frequency are
dierent from the parameters specied on the casing of the Milling
Cutter.
2. Do not try to plug or unplug the Milling Cutter with wet hands.
3. Always insert the plug deeply to the end.
4. Never pull the power cable to withdraw the plug out of the wall
socket.
5. Avoid damage to and do not modify and do not stretch the power
cable and the connection cable. Do not put any items onto them. The
connection cable remains under big workload while in use, therefore
it would quickly break down if used improperly (e.g. knots and loops
in the cable, constant bending at sharp angles, abrupt moves).
6. Do not switch the Milling Cutter on if the power cable or
connection cable is looped or knotted.
7. Do not plug the Milling Cutter in a wall socket, which is used to
provide power to some other equipment (via extension cables,
T-junctions, etc.)
8. Use high-quality and properly operating tools (caps, milling tools,
etc.) only. Shank ends must be plain-shaped and all parts of the tools
must be rmly xed to each other. Do not use any worn tools as it
may result in their destruction.
9. When selecting the operation modes for the Milling Cutter, do not
go beyond the maximum permitted limits for a specic tool as it may
result in destruction of the tool and in breakdown of the Milling
Cutter.
5
Safety Precautions
In order to ensure safe operation of the Milling Cutter, please learn
the safety precautions specied in this User Guide. Do not try to use
the Milling Cutter is a manner not specied in this document. Do not
try to use the Milling Cutter for operations not specied in this
document.
Delivery Set
· Power unit
· Handheld milling cutter (micromotor)
· Micromotor pad
· Pedal (available in specic models)
· User Guide
· Packaging