multicomp pro MP008632 User manual

Page <1> V1.003/12/21
Newark.com/multicomp-pro
Farnell.com/multicomp-pro
sg.element14.com/b/multicomp-pro
1 Channel PoE Injector
User Manual
Part Number: MP008632

Page <2> V1.003/12/21
Newark.com/multicomp-pro
Farnell.com/multicomp-pro
sg.element14.com/b/multicomp-pro
Introduction
The PoE Injector is a single port PoE injector o󰀨er a compact and cost e󰀨ective, It can convert standard 100V/AC to 240V/AC
power into low voltage. DC that runs over existing LAN cable to power up IEEE 802.3af & at & bt compliant network
accessories. Remote powering of wireless LAN (WAN) access points, IP Security cameras, VOIP telephone and other low
port density installations.
The PoE Mid-spans no need to connect with external power supply and its associated AC/DC power cabling, providing a
compact, a󰀨ordable, safe and reliable power solution over existing ethernet infrastructure.
Features
• Full IEEE 802.3af IEEE 802.3at,IEEE802.3bt Compliant
• Up to 90W of Power on 4-pairs
• Auto-detect of POE IEEE 802.3af IEEE 802.3 at,IEEE 802.3bt equipment
• Supports 10/100/1000 Base-T applications
• LED indicators power input indication
• Distance up to 100 meters
• Internal AC/DC converter – no need for external power modules
• Easy plug-and-play installation
• Surge protection
Hard Ware Description

Page <3> V1.003/12/21
Newark.com/multicomp-pro
Farnell.com/multicomp-pro
sg.element14.com/b/multicomp-pro
DATA IN: PoE/DATA:
Connect to the Ethernet Connect to the camera with UTP
device with CAT5 UTP cable 5 to supply power
cable to transmit data.
PWR: Power LED, a steady green light indicates that the PoE injector got 100-240V power input
30W: When the output power is 0 to 30W, led lights up
60W: When the output power is 30 to 60W, led lights up
90W: When the output power is 60 to 90W, led lights up
Application
Use PoE Injector with PD to expand your network to where there are no power lines or outlets, where you wist to x devices
such as Aps, IP Cameras or IP Phones, etc.
Steps:
1. Use a CAT5 UTP cable to connect port of Ethernet device to the DATA IN port,
2. Connect AC cable with Injector and Socket
3. Connect the PoE OUT port to a PD with CAT5 UTP cable.

Page <4> V1.003/12/21
Newark.com/multicomp-pro
Farnell.com/multicomp-pro
sg.element14.com/b/multicomp-pro
Important Notice : This data sheet and its contents (the “Information”) belong to the members of the AVNET group of companies (the “Group”) or are licensed to it. No licence is granted for
the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change
without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness,
any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make
any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or
where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its
negligence. Multicomp Pro is the registered trademark of Premier Farnell Limited 2019.
Specication
Item Description
No. of channels 1
Pass Through Data Rates 10/100/1000Mbps
Power over Ethernet Output
Pin Assignment and Polarity
1/2(-)3/6(+), 4/5(+)7/8(-)
Output Power Voltage: 54V DC
User Port Power: 90W MAX
Input Power Requirements
AC Input Voltage: 100 to 240 V AC
AC Input Current: 1A 100-240 V AC
AC Frequency: 50 Hz to 60 Hz
Dimensions 173mm × 83mm × 44mm
Indicators
System indicator: AC Power
User Indicator: Channel Power
30W :When the output power is 0W to 30W, led lights up
60W :When the output power is 30W to 60W, led lights up
90W :When the output power is 60W to 90W, led lights up
Connectors Shielded RJ-45, EIA 568A and 568B
Protection
Over current protection
Over load protection
Over voltage protection
Anti-interference protection
Environmental Conditions
Operating Ambient Temperature:0°C to 45°C
Operating Humidity:
Maximum 80%, Non-condensing
Storage Temperature:-20°C to 70°C
Storage Humidity:
Maximum 80%, Non-condensing
Regulatory Compliance
IEEE 802.3af (15.4W)
IEEE 802.3at (30W)
IEEE802.3bt (90W)