MultiDyne MD9200-ENC User manual

© 2018 MultiDyne Specifications subject to change without notice Made in USA© 08/2017 MultiDyne Specifications subject to change without notice Made in USA
MD9200-ENC
10 Newton Place
Hauppauge, NY 11788
1-877-685-8439 / [phone]
[email protected]
www.multidyne.com
1. USB 2.0 for media, firmware update and factory restore.
2. Reset button. Press and release to reset. Press and hold 10 seconds to factory restore.
3. Status LEDs. Tx: encoding. SF: screen format. Rx: unused. WF: WiFi. LTE: cellular. DC: input voltage
active, flash indicates system is operational.
4. 12 Volt DC input.
5. microUSB for terminal. Not for users.
6. Monitor: audio and video jack.
1. HDMI output. Unused.
2. 3G SDI input.
3. Gigabit Ethernet port 1. Default avahi named address. [serial number].local/ Default is DHCP.
4. Gigabit Ethernet port 2. Default is 192.168.2.7.
5. USB 3.0 for media, firmware update and factory restore.
The MD9200-ENC uses a modern HTML5-embedded Web server for user configuration. Users can connect to the MultiDyne device via Gigabit Ethernet (GigE)
port 1 or GigE port 2. GigE port 1 is factory defaulted to DHCP and GigE port 2 is factory defaulted to 192.168.2.7.
© 2019 MultiDyne
FRONT PANEL
BACK PANEL
CONNECTING TO THE MD9200-ENC
LOGIN WITH IP ADDRESS:
Web UI Value
Username 9200
Password ENC
Gigabit Ethernet Port Configuration
GigE 1 DHCP
GigE 2 192.168.2.7
1 2 3 4 5
1 2 3 4 5 6
Stand-Alone OTT Streaming Media Encoder
Quick Start Sheet

© 2018 MultiDyne Specifications subject to change without notice Made in USA
Update Firmware
© 08/2017 MultiDyne Specifications subject to change without notice Made in USA
MD9200-ENC
10 Newton Place
Hauppauge, NY 11788
1-877-685-8439 / [phone]
[email protected]
www.multidyne.com
1. Log into the MD9200-ENC web GUI and navigate to the HOST Tab.
2. Download the firmware to a disk and folder on your Windows/MAC/
Linux computer.
3. Choose File (firmware) from your computer’s disk and folder.
4. Click “Upload” button to upload the firmware from your computer to
the MD9200-ENC.
5. Count down number in “OK” button indicates how long until update
automatically continues. Click “OK” to immediately start update.
6. “Update has begun” prompt. Select “OK” close the window.
The MD9200-ENC supports USB2 and USB3 media devices. To upload the new firmware from a USB media device (thumb-drive), follow the steps below.
1. Download the firmware to a disk and folder on your computer.
2. Copy the firmware file from your computer’s disk and folder to the USB media device.
a. There must ONLY be one copy of the firmware on the media device. Remove previous versions before inserting the media device into the MD9200-
ENC USB interface.
3. Safely remove the media device from your PC.
4. Insert the media device into the USB interface on the MD9200-ENC.
5. The top green LED will go o once the system mounts the media device and starts the upgrade script. The disk mount and script start takes about 10
seconds. The upgrade will take a little over a minute to complete. The device will reboot automatically.
6. You can remove the USB media device from the MD9200-ENC after the unit reboots and starts decoding.
7. To confirm the update was successful:
8. If more that one unit is upgraded using the same USB media device, there will be a firmware update log for each unit. The naming scheme for the
firmware update log is <SN>-firmwareUpdate.log
UPGRADING FIRMWARE FROM THE WEB UI
UPLOADING NEW FIRMWARE FROM A USB DISK
Update Firmware
© 2019 MultiDyne
Stand-Alone OTT Streaming Media Encoder
Quick Start Sheet