Multitech MULTIVOIP MVP-410ST User manual

R
MultiVOIP ISDN BRI
Voice / Fax over IP Networks
MVP410ST
MVP810ST
Cabling Guide

MultiVOIP ISDN/BRI Cabling Guide
2 Multi-Tech Systems, Inc.
Cabling Guide
ISDN/BRI Voice/Fax over IP Networks
Models MVP410ST and MVP810ST
82100250L Rev. A
Copyright
This publication may not be reproduced, in whole or in part, without prior expressed
written permission from Multi-Tech Systems, Inc. All rights reserved.
Copyright © 2007 Multi-Tech Systems, Inc.
Multi-Tech Systems, Inc. makes no representations or warranty with respect to the
contents hereof and specifically disclaims any implied warranty of merchantability or
fitness for any particular purpose. Furthermore, Multi-Tech Systems, Inc. reserves
the right to revise this publication and to make changes from time to time in the
content hereof without obligation of Multi-Tech Systems, Inc. to notify any person or
organization of such revisions or changes. Check Multi-Tech’s web site for current
versions of our product documentation.
Revision Date Description
A 01/12/07 Transition to cabling guide from Quick
Start. (Last QS version was 82100002L.)
Quick setup info transferred to chapter of
companion User Guide (S000385B and
any subsequent).
Trademarks
Multi-Tech and the Multi-Tech logo are registered trademarks of Multi-Tech
Systems, Inc. MultiVOIP is a registered trademark of Multi-Tech Systems, Inc. All
other brand and product names mentioned in this publication are trademarks or
registered trademarks of their respective companies.
Patents
This Product is covered by one or more of the following U.S. Patent Numbers:
6151333, 5757801, 5682386, 5.301.274; 5.309.562; 5.355.365; 5.355.653;
5.452.289; 5.453.986. Other Patents Pending.
GENERAL CONTACT TECHNICAL SUPPORT
Country By E-mail By Phone
France support@
multitech.fr (+33) 1-64
61 09 81
India support@
multitechindia.
com
(+91) 124-
2340780
Europe,
Asia,
Africa
support@
multitech.co.uk ([phone]
Multi-Tech
Systems, Inc.
2205 Woodale Drive
Mounds View,
Minnesota
55112, USA
[phone]
[phone]
Fax: [phone]
www.multitech.com
U.S.,
Canada,
All Others
support@
multitech.com (800) 972- 2439; (763)
717-5863

MultiVOIP ISDN/BRI Cabling Guide
Multi-Tech Systems, Inc. 3
Introduction
This guide shows you how to make the cable connections to set up your
MultiVOIP®ISDN/BRI unit. See the MultiVOIP User Guide included on the
MultiVOIP CD for more information. The “Quick Start Instructions” chapter shows
how to get the MultiVOIP ISDN/BRI unit up and running with a basic configuration.
Safety Warnings
Lithium Battery Caution
A lithium battery on the voice/fax channel board provides backup power for the
timekeeping capability. The battery has an estimated life expectancy of ten
years.
When the battery starts to weaken, the date and time may be incorrect. If the
battery fails, the board must be sent back to Multi-Tech Systems for battery
replacement.
Warning: There is danger of explosion if the battery is incorrectly
replaced.
Ethernet Ports Caution
Caution: The Ethernet ports and command ports are not designed to
be connected to a Public Telecommunictaion network.
Safety Warnings Telecom
•Use this product only with UL- and CUL-listed computers (US).
•Never install phone wiring during a lightning storm.
•Never install a phone jack in a wet location unless the jack is specifically
designed for wet locations.
•Never touch uninsulated phone wires or terminals unless the phone line has
been disconnected at the network interface.
•Use caution when installing or modifying phone lines.
•Avoid using a phone during an electrical storm; there is a risk of electrical
shock from lightning.
•Do not use a phone in the vicinity of a gas leak.
•To reduce the risk of fire, use only 26 AWG or larger telephone line cord.
•This product must be disconnected from power source and telephone
network interface when servicing.
Safety Recommendations for Rack Instructions
•Ensure proper installation of the MultiVOIP in a closed or multi-unit
enclosure by following the recommended installation as defined by the
enclosure manufacturer. Do not place the MultiVOIP directly on top of other
equipment or place other equipment directly on top of the MultiVOIP.
•If installing the MultiVOIP in a closed or multi-unit enclosure, ensure
adequate airflow within the rack so that the maximum recommended
ambient temperature is not exceeded.

MultiVOIP ISDN/BRI Cabling Guide
4 Multi-Tech Systems, Inc.
Safety Recommendations for Rack Instructions (cont’d)
•Ensure that the MultiVOIP is properly connected to earth ground via a
grounded power cord. If a power strip is used, ensure that the power strip
provides adequate grounding of the attached apparatus.
•Ensure that the mains supply circuit is capable of handling the load of the
MultiVOIP. Refer to the power label on the equipment for load requirements.
•Maximum ambient temperature for the MultiVOIP is 60 degrees Celsius
(140°F) at 20-90%s non-condensing relative humidity.
•This equipment should only be installed by properly qualified service personnel.
•Only connect like circuits. In other words, connect SELV (Secondary Extra
Low Voltage) circuits to SELV circuits and TN (Telecommunications
Network) circuits to TN circuits.
•To reduce the risk of shock, all access doors should be closed during
normal operation of the equipment.
•

MultiVOIP ISDN/BRI Cabling Guide
Multi-Tech Systems, Inc. 5
MVP-410ST/810ST Package Contents
•One MultiVOIP MVP410ST or MVP810ST
•One power cord
•One Command Cable (DB25-to-DB9 connectors)
•Two rack mount brackets and four mounting screws
•One printed Cabling Guide
•One MultiVOIP CD containing software and user documentation.
FDX
LNK XMT RC V XMT RCV XMT RCV XMT XMT RCV XMT
Cabling
Guide
MultiVOIPTM
RCV
D
RCV
D
ISDN 1 ISDN2 ISDN 3 ISDN 4
Ethernet
BootPower
XMT RCV XMT RCV
Ch1 Ch2 Ch3 Ch4
DD
Ch5 Ch6 Ch7 Ch8

MultiVOIP ISDN/BRI Cabling Guide
6 Multi-Tech Systems, Inc.
Quick Hookup for MVP410ST & MVP810ST

MultiVOIP ISDN/BRI Cabling Guide
Multi-Tech Systems, Inc. 7
Earth Ground Connection & Power-Up
Product
Ground
Screw
Grounding connectors
must be secured
permanently to
product ground screw
and earth ground screw.
Earth Ground Screw:
Connected to
Permanent Earth Ground
of Building’s
Electrical System
Ground
Wire:
Size 18AWG
or thicker
MultiVOIP
Unit
GND
Ground Connection. Ensure that the unit is securely and permanently
connected to an earth ground (GND) with a ground wire of 18 gauge (18
AWG) or thicker. The ground wire needs to be installed between the
grounding screw on the MultiVOIP chassis and a permanent earth ground.
Whether the unit is used in a rack or on a desktop, you must verify that the
earth ground connection is permanent and reliable. In order for the ground
connection to be considered permanent, the grounding wire must connect to
the earth ground of the building's electrical wiring system and the ground
connection must use a screw terminal or other reliable means of fastening.
The ground connection must not be as easily disconnected as, for example, a
power cord.
VOIP Configuration
When the cabling connections above have been made, go to the “Quick Start
Instructions” chapter of the User Guide (on your MultiVOIP CD) for detailed
instructions about configuration.

82100250L