mundoclima MUP User manual

SPLIT AIR CONDITIONER
MUP/MUPR HL
OWNER’S MANUAL

CONTENTS
SAFETY PRECAUTIONS
NAMES OF THE PARTS
INDOOR UNIT DISPLAY
MODES OF OPERATION
PROTECTION
INSTALLATION MANUAL
MAINTENANCE
TROUBLESHOOTING
EMERGENCY FUNCTION & AUTO-RESTART FUNCTION
REMOTE CONTROL
....................................................................................................1
..........................................................................................................3
.........................................................................................................4
..............................................5
...............................................................................................................6
........................................................................................................9
.........................................................................................................................14
....................................................................................................15
....................................................................................................................24
..........................................................................................................25

During the installation of the indoor and outd-
oor units the access to the working area should
be forbidden to children.
Unforeseeable accidents could happen.
Make sure that the base of the outdoor unit is
firmly fixed.
Check that air cannot enter the refrigerant sys-
tem and check for refrigerant leaks when mo-
ving the air con ditioner.
SAFETY RULES AND RECOMMENDATIONS FOR THE INSTALLER
Carry out a test cycle after installing the air co-
nditioner and record the operating data.
The ratings of the fuse installed in the built in-
control unit are 3.15A / 250V for 220V type
and 3.15A/125V for 110V type .
The user must protect the indoor unit with a
fuse of suitable capacity for the maximum in-
put current or with another overload protection
device.
Ensure that the mains voltage corresponds to
that stamped on the rating plate . Keep the sw-
itch or power plug clean. Insert the power plug
correctly and firmly into the socket, thereby a-
voiding the risk of electric shock or fire due to
insufficient contact.
Check that the socket is suitable for the plug ,
otherwise have the socket changed.
Do not install the appliance at a distance of
less than 50 cm from inflammable substances
(alcohol, etc.) Or from pressurised containers
(e.g. spray cans).
If the appliance is used in areas without the
possibility of ventilation, precautions must be
taken to prevent any leaks of refrigerant gas
from remaining in the environment and creat-
ing a danger of fire
The packaging materials are recyclable and
should be disposed of in the separate waste
bins .Take the air conditioner at the end of its
useful life to a special waste collection centre
for disposal.
Only use the air conditioner as instructed in
this booklet . These instructions are not inten-
ded to cover every possible condition and
situation . As with any electrical household
appliance , common sense and caution are
therefore always recommended for installat-
ion, operation andmaintenance.
The appliance must be installed in accordance
with applicable national regulations.
Before accessing the terminals , all the power
circuits must be disconnected from the power
supply.
Read this guide before installing and using the
appliance.
SAFETY RULES AND RECOMMENDATIONS FOR THE USER
Do not try to install the conditioner alone;
always contact specialized technical personnel.
Cleaning and maintenance must be carried out
by specialised technical personnel. In any case
disconnect the appliance from the mains elect-
ricity supply before carrying out any cleaning
or maintenance.
Ensure that the mains voltage corresponds to
that stamped on the rating plate. Keep the swi-
tch or power plug clean. Insert the power plug
correctly and firmly into the socket , thereby
avoiding the risk of electric shock or fire due
to insufficient contact.
Do not pull out the plug to switch off the app-
liance when it is in operation, since this could
create a spark and cause a fire, etc.
If the appliance gives off smoke or there is a
smell of burning, immediately cut off the pow
er supply and contact the Service Centre.
Have repairs carried out only by an authoris-
ed Service Centre of the manufacturer . Inco-
rrect repair could expose the user to the risk
of electric shock, etc.
The prolonged use of the device in such
conditions could cause fire or electrocution.
Never remain directly exposed to the flow of
cold air for a long time. The direct and prolo-
nged exposition to cold air could be dangero-
us for your health .Particular care should be
taken in the rooms where there are children ,
old or sick people.
1

SAFETY RULES AND RECOMMENDATIONS FOR THE USER
This appliance has been made for air conditi-
oning domestic environments and must not be
used for any other purpose , such as for drying
clothes, cooling food, etc.
The packaging materials are recyclable and
should be disposed of in the sparate waste
bins . Take the air conditioner at the end of its
useful life to a special waste collection centre
for disposal.
Only use the air conditioner as instructed in
this booklet.These instructions are not int end-
ed to cover every possible condition and situ-
ation.As with any electrical household applia-
nce, common sense and caution are therefore
always recommended for installation , operat-
ion and maintenance.
Always use the appliance with the air filter
mounted . The use of the conditioner without
air filter could cause an excessive accumulation
of dust or waste on the inner parts of the device
with possible subsequent failures.
Unhook the automatic switch if you foresee
not to use the device for a long time.
The airflow direction must be properly adjus-
ted.
The flaps must be directed downwards in
the heating mode and upwards in the cooling
mode.
SAFETY RULES AND PROHIBITIONS
Do not bend , tug or compress the power cord
since this could damage it. Electrical shocks or
fire are probably due to a damaged power cord.
Specialised technical personnel only must repl-
ace a damaged power cord.
Do not use extensions or gang modules.
Do not touch the appliance when barefoot or
parts of the body are wet or damp.
Do not obstruct the air inlet or outlet of the in-
door or the outdoor unit.
The obstruction of these openings causes a re-
duction in the operative efficiency of the con-
ditioner with possible consequent failures or
damages.
In no way alter the characteristics of the appli-
ance.
Do not install the appliance in environments
where the air could contain gas , oil or sulphur
or near sources of heat.
Do not climb onto or place any heavy or hot
objects on top of the appliance.
Do not leave windows or doors open for long
when the air conditioner is operating.
Do not direct the airflow onto plants or anim-
als.
A long direct exposition to the flow of cold
air of the conditioner could have negative
effects on plants and animals.
Do not put the conditioner in contact with
water.
The electrical insulation could be damaged
and thus causing electrocution.
Do not climb onto or place any objects on the
outdoor unit
Never insert a stick or similar object into the
appliance. It could cause injury.
The user is responsible for having the appliance
installed by a qualified technician , who must
check that it is earthed in accordance with curr-
ent legislation and insert a thermomagnetic cir-
cuit breaker.
Ensure that the appliance is disconnected from
the power supply when it will remain inoperat-
ive for a long period and before carrying out
any cleaning or maintenance.
Selecting the most suitable temperature can pr-
event damage to the appliance.
2

NAMES OF THE PARTS
No. Description
1
2
Front panel
Air filter
Optional filter (if installed)
3
Terminal block cover
4
Emergency button
5
6
LED Display
Signal receiver
7
Airflow direction flaps
8Deflectors
9
Remote control
10
Note: the above figures are only intended to be a
simple diagram of the appliance and may not
correspond to the appearance of the units that
have been purchased.
No. Description
13 Air outlet grille
Cover
14
gas valve
15
liquid valve
16
11
Indoor unit rating label
17
Outdoor unit rating label
WALL AIR-CONDITIONER
The conditioner is made up of two or more units
connected between themselves through copper
pipes (properly insulated) and an electrical con-
necting cable.
The indoor unit is installed on the walls of the
room to be conditioned.
The outdoor unit is installed on the floor or on the
wall on suitable brackets.
Technical data of the air conditioner are printed on
the labels placed on the indoor and outdoor units.
The remote control has been designed for an easy
and fast use.
12
Ionizer (if installed)generator
13
15
16
17
INDOOR UNIT
3
OUTDOOR UNIT
12-3
6
4-5
9
11 8
10 7
14
DISPLAY HEALTHY
3D
ON/OFF
SWING
FAN
TIMERSUPER
SLEEPMODE
ECO
CLOCK
12

INDOOR UNIT DISPLAY
No.
/O
1
2
5
3
4
1 2 345
Led Function
POWER Shows that the unit is powered
1
2
3
4
5
Temperature display (if present) Indicates the set temperature in or F
SLEEP mode
TIMER mode
Unit working
The shape and position of switches and indicators may vary according to the model, but their function
is the same.
SLEEP
TIMER
RUN
12 4 5
3
4
1
2
3
4
5

EMERGENCY FUNCTION & AUTO-RESTART FUNCTION
ON/OFF
Emergency
button
The emergency button in some
models could be on the right part
of the unit under the front panel.
The shape and position of the emergency button
may vary according to the model, but their
function is the same.
The appliance is preset auto - restart function by
manufacturer.with this function the air conditioner
can keep the selected settings after a blackout or a
voltage drop.
Lift the unit s front panel to reach the emergency
button of the air conditioner
1. if you press the button once ( one beep ), the air
conditioner will work in forced cooling function;
2. if you press the button twice ( two beeps ), the
unit will work in forced heating function.
3. To switch off the unit , you just need to press
the button again ( a single long beep) . After 30
minutes in forced function , the air conditioner
will automatically start working in FEEL mode .
The FEEL function is described in page 13.
If the remote control is lost, proceed as follows:
display PCB
front panel
To deactivate the AUTO-RESTART function ,pro-
ceed as follows:
1. Switch the air conditioner off and plug it off.
2. Press the emergency button meanwhile plug
it in.
3. Keep pressing the emergency button for more
than 10 seconds until you hear four short beeps
from the unit. The AUTO-RESTART function is
off.
To activate the AUTO - RESTART function ,
follow the same procedure until you hear three
short beeps from the unit.
Emergency
button
ON / OFF
POWER
SLEEP
TIMER
RUN
EMERGENCY FUNCTION
AUTO-RESTART FUNCTION
5
Emergency
button

REMOTE CONTROL
6
The shape and position of buttons and indicators may vary according to
the model, but their function is the same.
The outlooking and some function of remote control may vary according
to the model.
The unit confirms the correct reception of each press button with a beep.
To select the mode of operation
To LED display (if present)switch on/off the
To activate or deactivate of the movement of the
DEFLECTORS .
To activate the function SLEEP
To switch - on /off HEALTHY funtion.It is a button
which controls the ionizer or plasma generator only
for inverter type.
In cooling mode,press this button ,the temperature
will increase 2 on the base of setting temperature
In heating mode, press this button, the temperature
will decrease 2 on the base of setting temperature
In cooling mode, press this button, the unit will give
the maximum cooling temperature with 16
In heating mode, press this button, the unit will give
the maximum heating temperature with 31
Decrease the temperature or time by 1 unit
Increase the temperature or time by 1 unit
To switch the conditioner on and off.
To set automatic switching-on/off
To select the fan speed of auto/low/mid/high
No.
8
10
12
6
14
7
9
13
MODE
SWING
DISPLAY
SLEEP
HEALTHY
ECO
SUPER
11
3D
CLOCK
1
(TEMP DN)
(TEMP UP)
2
3
4
ON/OFF
FAN
5TIMER
This button is useless for wall-mounted type.
When you press "3D", the horizontal and vertical
vanes will swing together at the same time.
RESET
ANTI-MILDEW
Button Function
To activate the function ANTI-MILDEW
To restart REMOTE CONTROL
SLEEP
TIMER SWING
MODE
ON/OFF
2
1
6
5
8
FAN
3
10
4
Auto
Feel Cool
Low
Dry Heat
Mid High Sleep Swing
Timer
OFF
Timer
Fan
C
h
ON/OFF
SWING
FAN
TIMER SUPER
SLEEPMODE
ECO
111
3
2
9
13
8
12
4
14
10
5
6
DISPLAY HEALTHY3D
CLOCK
7
1
3
4
5
12
13
10
9
8
7
6
ON OFF ON
C
AUTOQUIET
POWERFUL
hr
DELAY
DRY
FAN
HEAT
TIMER
HEALTHY
AIR
SWING
FAN
SPEED
2
COOL
FEEL
ON/OFF
MODE TIMER
FAN SPEED SUPER ECO
ANTI-MILDEW
SWING SLEEP HEALTHY
DISPLAY RESET
15
16
16
15
When you pressthis button,the timewill be flic-
kering;then through" "and" ",you canadjust
the time(one timeyou press,one minute you ad-
just;and if youcontinue to press,the time change
rapidly ), afteradjusting to your required time,
please press thisbutton again tofix the time.

Auto
Feel Cool Dry Heat
Low Mid High Sleep Swing
Timer
OFF
Timer
Fan
REMOTE CONTROL
Remote control DISPLAY
Meaning of symbols on the liquid crystal display
1
2
3
4
5
6
7
8
9
10
11
12
13
14
FEEL mode indicator
COOLING indicator
DEHUMIDIFYING indicator
FAN ONLY OPERATION indicator
HEATING indicator
SIGNAL RECEPTION indicator
TIMER OFF indicator
TIMER ON indicator
AUTO FAN indicator
LOW FAN SPEED indicator
or MIDDLE FAN SPEED indicator
or
or
HIGH FAN SPEED indicator
QUIET or
or SLEEP indicator
or
AUTO or
or FLAP SWING indicator
15
SUPER indicator
16
17
HEALTHY indicator
TIMER
ON
or
or
TIMER
OFF
or
HEALTHY
ON
18
ECO indicator
19
ANTI-MILDEW indicator
ON OFF ON
C
AUTOQUIET
POWERFUL
hr
DELAY
DRY
FAN
HEAT
TIMER
HEALTHY
AIR
SWING
FAN
SPEED
COOL
FEEL
or
POWERFUL
or
7
or EC
C
h
C
h
MID
AUTO
SLEEP
TIMER ON
HIGH
LOW
TMIER OFF
DRY
FAN
HEAT
COOL
FEEL
SWING
or
BATTERY indicator
or
or
or
or
or
or
or
or
or
20
21
22
COMFORTABLE SLEEP indicator (optional)
I FEEL indicator(optional)
Meaning
No. Symbols
TIMER
HEALTHY
(FLASH)
FLAP and Deflectors SWING indicator
CLOCK indicator
23

REMOTE CONTROL
Preliminary Instructions
How to insert the batteries
Remove the cover from the battery compartment , by sliding it in the
direction of the arrow
Insert the new batteries, ensuring that the (+) and (-) directions are
correct
Refit the cover by sliding it into place.
Use 2 LRO 3 AAA (1.5V) batteries . Do not use rechargeable
batteries . Replace the old batteries with new ones of the same
type when the display is no longer legible.
The remote control batteries must be disposed of in accordance
with the applicable laws in force in the country of use.
BE CAREFUL:if you adjust the remote control in cooling mode,
it will not be possible to activate the heating function in units with
heating pump . you need to take out the batteries and repeat again
the procedure described above.
1. Direct the remote control toward the conditioner.
2. Check that there are no objects between the remote control
and the receiver on the conditioner.
3. Never leave the remote control exposed to the rays of the sun.
4. Keep the remote control at a distance of at least 1m from the
television or other electrical appliances.
Recommendations for locating and using the remote control (if present)
The remote control may be kept in a wall-mounted holder
Signal
receptor
Refer to picture 2:
When you insert the batteries for the first time in the remote
control or if you change them, you need to program the remote
control of only cooling or heat pump air conditioners.
This is very easy:as soon as you insert the batteries, the symbols
( ) and ( ) start fashing. If you push
whatever button when the symbol ( ) is displayed,the
remote control is adjusted in only cooling mode . If you push
whatever button when the symbol ( ) is displayed ,
the remote control is adjusted in heating mode.
8
COOL HEAT
COOL
HEAT
DRY
FAN
HEAT
TIMER
HEALTHY
AIR
SWING
FAN
SPEED
COOL
FEEL
DRY
FAN
HEAT
TIMER
HEALTHY
AIR
SWING
FAN
SPEED
COOL
FEEL
Refer to picture 1:
i. When you insert the batteries for the first time in the remote
control or if you change them,you will see a DIP switch under
the back cover.
ii. BE CAREFUL:After adjusting the function, you need to take
out the batteris and repeat again the procedure described above.
+
+
+
DIP switch on position Function
The display is adjusted in degree celsius
The remote control is adjusted in only cooling mode
The remote control is adjusted in only heating mode
The display is adjusted in degree fahrenheit.
DISPLAY HEALTHY
3D
ON/OFF
SWING
FAN
TIMER SUPER
SLEEPMODE
ECO
CLOCK
Remote controller holder
DISPLAY HEALTHY
3D
ON/OFF
SWING
FAN
TIMER SUPER
SLEEPMODE
ECO
CLOCK
DISPLAY HEALTHY
3D
ON/OFF
SWING
FAN
TIMER SUPER
SLEEPMODE
ECO
CLOCK
Cool
Heat
C
F

MODES OF OPERATION
flaps
flap
movement Deflectors
Filter
Heat
Fan
Exchanger
“SWING”CONTROL OF THE AIR FLOW
AIR
SWING
The air outlet flow is uniformly dist-
ributed in the room.
It is possible to position the direction
of the air in the optimal solution.
The key SWING activates the FLAP ,the air flow
is directed alternatively from up to down .
In order to guarantee an even diffusion of the air in the
room.
In cooling mode , orient the flaps in horizontal
direction;
In heating mode, orient the flaps downward as
the warm air always tends to rise upward.
The deflectors are positioned manually and placed un-
der the flaps .They allow to direct the air flow rightw-
ard or leftward.
CAUTION!
Never position Flaps manually, the delicate mech-
anism activating them could be seriously damaged!
DANGER!
Never insert your hand or objects in the air outlet of
the units!These units contains a fan that turns at high
speed.
This adjustment must be done with the appliance
switched off.
AIR
SWING
OFF ON
C
AUTOQUIET
POWERFUL
hr
DELAY
TIMER
HEALTHY
AIR
SWING
FAN
SPEED
9
The conditioner is designed to create the comfortable
climatic conditions for the people in the room.
When the cycle has finished the fan gives back the
fresh air in the room;the direction of the air outlet is
regulated by the flaps , which are motorized up and
down,and manually moved right and left by the verti-
cal deflectors
The heat removed from the room is drained outside.
The air sucked by the fan enters from the grill of the
front panel and passes through the filter, which keeps
the dust.Then it is conveyed the heat exchanger and
cooled and dehumidified or heated through the heat
exchanger.
It can cool and dehumidify (and heat in models with
heat pump) the air in a completely automatic way.
ON/OFF
MODE TIMER
FAN SPEED SUPER ECO
SWING SLEEP HEALTHY
DRY
FAN
HEAT
COOL
FEEL
ANTI-MILDEW
C
h
ON
TIMER
HEALTHY

MODES OF OPERATION
COOLING MODE
The cooling function allows the air condit-
ioner to cool the room and at the same time
reduces the humidity in the air.
COOL
To activate the cooling function ( COOL ) , press the
MODE button until the symbol ( COOL )
appears on the display.
The cooling cycle is activated by setting the keys
or at a temperature lower than that of the room.
To optimize the functioning of the conditioner, adjust
the temperature (1) , the speed (2) and the direction
of the air flow (3) by pressing the keys indicated
HEAT
The heating function allows the air conditi-
oner to produce hot air.
To activate the heating function ( HEAT ) , press the
MODE button until the symbol ( HEAT )
appears on the display.
With the keys or set a temperature higher than
that of the room..
To optimize the functioning of the conditioner adjust
the temperature ( 1 ), the speed ( 2 ) and the direction
of the air flow ( 3 ) by pressing the keys indicated
In HEATING operation, the appliance can automa-
tically activate a defrost cycle, which is essential
to free the condenser from an excessive deposit of
frost .This procedure usually lasts for 2-10 minutes
during defrosting,fans stop operation. After defros-
ting ,it returns to HEATING mode automatically.
The appliance is fitted with a Hot Start function,
which delays appliance to startup in a few seconds
to ensure an immediate output of hot air.
10
HEATING MODE
OFF ON
C
AUTOQUIET
POWERFUL
hr
DELAY
TIMER
HEALTHY
AIR
SWING
FAN
SPEED
ON/OFF
MODE TIMER
FAN SPEED SUPER ECO
SWING SLEEP HEALTHY
DRY
FAN
HEAT
COOL
FEEL
ANTI-MILDEW
C
h
ON
COOL
1
2
3
OFF
C
AUTOQUIET
POWERFUL
TIMER
HEALTHY
DRY
FAN
HEAT
COOL
FEEL
ON
HEAT
ON
hr
DELAY
AIR
SWING
FAN
SPEED
C
h
1
ON/OFF
MODE TIMER
FAN SPEED SUPER ECO
SWING SLEEP HEALTHY
ANTI-MILDEW
1
2
3
1
TIMER
HEALTHY
TIMER
HEALTHY

MODES OF OPERATION
TIMER
ON To set the automatic switching-on of
the air conditioner
To program the time start,the appliance should be off.
Press TIMER , Set the temperature with pressing the
key or ,Press TIMER Again , set the time with
pressing the key or , Press the key more times till
on the display you can read the time which passes between
the programming and the timed start.
FAN
SWING
SLEEP
POWER SLEEP TIMER RUN
Indoor display
IMPORTANT!
Before proceeding with the timed start : program the
working mode with the key MODE (2) and the
fan speed with the key FAN (3) . Switch the con-
ditioner off (with the key ON/OFF ).
TIMER
To set the automatic switching-off of
the air conditioner
The timed stop is programmed with the appliance on.
Press TIMER ,Set the time pressing the key or ,
Press the key more times till on the display you can read
the time which passes between the programming and the
timed stop.
OFF
Note:To cancel the setted function ,press the TIMER
button again.
Note:To cancel the setted function, press the TIMER
button again.
Note:In case of power off,it is necessary to set TIMER
ON again
Note:In case of power off,it is necessary to set TIMER
OFF again
11
TIMER MODE----TIMER OFF
TIMER MODE----TIMER ON
FAN
SWING
SLEEP
POWER SLEEP TIMER RUN
Indoor display
TIMER
ON
OFF ON
C
AUTOQUIET
POWERFUL
hr
DELAY
TIMER
HEALTHY
AIR
SWING
FAN
SPEED
ON/OFF
MODE TIMER
FAN SPEED SUPER ECO
SWING SLEEP HEALTHY
DRY
FAN
HEAT
COOL
FEEL
ANTI-MILDEW
C
h
ON
1
2
3
TIMER
HEALTHY TIMER
HEALTHY
Note: While the time was right settled, the
TIMER function of this remote(clock
function) can set by half hours
TIMER
HEALTHY
FAN
SWING
SLEEP
POWER SLEEP TIMER RUN
Indoor display
TIMER
OFF ON
C
AUTOQUIET
POWERFUL
hr
DELAY
TIMER
HEALTHY
AIR
SWING
FAN
SPEED
DRY
FAN
HEAT
COOL
FEEL
C
h
ON
OFF
ON/OFF
MODE TIMER
FAN SPEED SUPER ECO
SWING SLEEP HEALTHY
ANTI-MILDEW
1

MODES OF OPERATION
FAN
The conditioner works in only
ventilation.
To set the FAN mode , Press MODE untill
( FAN ) appears in the display.
Whith pressing FAN button the speed changes
in the following sequence: LOW/ MEDIUM/HIGH
/AUTO in FAN mode.
The remote control also stores the speed that was set
in the previous mode of operation.
In FEEL mode (automatic) the air conditioner auto-
matically chooses the fan speed and the mode of
operation (COOLING or HEATING).
This function reduces the humid-
ity of the air to make the room
more comfortable.
To set the DRY mode , Press MODE untill
( DRY ) appears in the display .An automatic
function of alternating cooling cycles and air fan
is activated.
DRY
12
FAN MODE
DRY MODE
OFF ON
C
AUTOQUIET
POWERFUL
hr
DELAY
TIMER
HEALTHY
AIR
SWING
FAN
SPEED
ON/OFF
MODE TIMER
FAN SPEED SUPER ECO
SWING SLEEP HEALTHY
DRY
FAN
HEAT
COOL
FEEL
ANTI-MILDEW
C
h
ON
3
FAN
DRY
OFF ON
C
AUTOQUIET
POWERFUL
hr
DELAY
TIMER
HEALTHY
AIR
SWING
FAN
SPEED
ON/OFF
MODE TIMER
FAN SPEED SUPER ECO
SWING SLEEP HEALTHY
DRY
FAN
HEAT
COOL
FEEL
ANTI-MILDEW
C
h
ON
TIMER
HEALTHY
TIMER
HEALTHY

MODES OF OPERATION
FEEL Automatic mode.
To activate the FEEL (automatic) mode of operation,
press the MODE button on the remote control until
the symbol ( FELL ) appears in the display.
In the FEEL mode the fan speed and the temperature
are set automatically according to the room tempera-
ture (tested by the probe which is incorporated in the
indoor unit)to ensure user comfort.
Ambient temp Auto temp.
20 23
23
26
20 ~26
Operation mode
HEATING ( FOR HEAT PUMP TYPE)
DRY
COOL
18
FAN (FOR COOL ONLY TYPE)
To optimize the working of the conditioner , adjust
the temperature(only 2 )(1), the speed (2) and the
direction of the air flow (3) by pressing the buttons
indicated
To activate the SLEEP mode of operation, press the
SLEEP button on the remote control until the sym-
bol (AUTOQUIET ) appears in the display.
AUTO QUIET
The function SLEEP automatically adjusts the
temperature to make the room more comfortable
during the night sleep . In cooling or dry mode , the
set temperature will automatically raise by1 every
60 minutes, to achieve a total rise of 2 during the
first 2 hours of work.
In heating mode the set temperature is gradually
decreased by 2 during the first 2 hours of work.
After 10 hours running in sleep mode the air conditio-
ner is swicthed off automatically.
13
FEEL MODE
FAN
SWING
SLEEP
POWER SLEEP TIMER RUN
Indoor display
FEEL
OFF ON
C
AUTOQUIET
POWERFUL
hr
DELAY
TIMER
HEALTHY
AIR
SWING
FAN
SPEED
DRY
FAN
HEAT
COOL
FEEL
C
h
ON
ON/OFF
MODE TIMER
FAN SPEED SUPER ECO
SWING SLEEP HEALTHY
ANTI-MILDEW
1
2
3
OFF ON
C
AUTOQUIET
POWERFUL
hr
DELAY
TIMER
HEALTHY
AIR
SWING
FAN
SPEED
DRY
FAN
HEAT
COOL
FEEL
C
h
ON
ON/OFF
MODE TIMER
FAN SPEED SUPER ECO
SWING SLEEP HEALTHY
ANTI-MILDEW
AUTOQUIET
SLEEP MODE
1
TIMER
HEALTHY
TIMER
HEALTHY

PROTECTION
The protective device maybe trip and stop the appliance in the cases listed below.
Outdoor air temperature is over 24
2
Room temperature is over 27
Outdoor air temperature is below -7
1
3
Heating
Cooling
Dry
Outdoor air temperature is over 43
Room temperature is below 21
Room temperature is below 18 C
For T1 Climate condition models:
For Tropical (T3) Climate condition models:
After stopping and restarting the air coditioner or after changing the mode during operation, the
system does not restart immediately, Untill after 3 minutes(protection function for the compressor)
14
No.
MODEL
2
1
3
Heating
Cooling
Dry
No.
MODEL
Outdoor air temperature is over 24
Room temperature is over 27
Outdoor air temperature is below -7
Outdoor air temperature is over 52
Room temperature is below 21
Room temperature is below 18 C

INSTALLATION MANUAL---Selecting the Installation Place
Install the indoor unit level on a strong wall that is not
subject to vibrations.
The inlet and outlet ports should not be obstructed:the
air should be able to blow all over the room.
Do not install the unit near a source of heat , steam,or
flammable gas.
Install the unit near an electric socket or private circuit.
Do not install the unit where it will be exposed to
direct sunlight.
Install the unit where connection between indoor and
outdoor unit is as easy as possible.
Install the unit where it is easy to drain the condensed
water.
Check the machine operation regularly and leave the
necessary spaces as shown in the picture.
Install the indoor unit where the filter can be easily
accessible.
condensed water drain pipe
150
150
150
Sleeve
insulating covering
electrical cable
Mounting plate
Do not install the outdoor unit near sources of heat,
steam or flammable gas.
Do not install the unit in too windy or dusty places.
Do not install the unit where people often pass.Select
a place where the air discharge and operating sound
level will not disturb the neighbours.
Avoid installing the unit where it will be exposed
to direct sunlight ( other wise use a protection , if
necessary, that should not interfere with the air flow).
Leave the spaces as shown in the picture for the air to
circulate freely.
Install the outdoor unit in a safe and solid place.
If the outdoor unit is subject to vibration, fix rubber
gaskets onto it.
water drain pipe
300
500
2000
300
minimum space to be left (mm) showing
in the picture
500
Outdoor unit
Indoor unit
Pipe length is
15 meters Max.
beless than 5m
Height should
Outdoor unit
Indoor unit
Pipe length is
15 meters Max.
be lessthan 5m
Heightshould
Installation Diagram
15
INDOOR UNIT
OUTDOOR UNIT

INSTALLATION MANUAL---Installation of the Indoor unit
1. By using a level, put the mounting plate in a perfect
square position vertically and horizontally.
2. Drill 32 mm deep holes in the wall to fix the
plate;
3. Insert the plastic anchors into the hole;
4. Fix the mounting plate by using the provided tapping
screws
5. Check that the mounting plate is correctly fixed;
50
5mm
Note : Keep the drain pipe down towards the direction
of the wall hole, otherwise leakage may occur.
Before starting installation, decide on the position of the
indoor and outdoor units, taking into account the minim-
um space required around the units
Install the indoor unit in the room to be air conditio-
ning, avoiding to install in corridors or communal
areas.
Install the indoor unit at a height of at least 2.5 m
from the ground.
To install, proceed as follows:
1. Decide where to drill the hole in the wall for the pip-
ing ( if necessary ) according to the position of the
mounting plate;
2. Install a flexible flange through the hole in the wall to
keep the latter intact and clean.
The hole must slope downwards towards the exterior
Note : The shape of the mounting plate may be different
from the one above, but installation method is similar .
Indoors Outdoors
1. Lift the front panel.
2. Take off the cover as indicated in the piciure ( by
removing a screw or by breaking the hooks).
3. For the electrical connections, see the circuit diagram
on the right part of the unit under the front panel.
4. Connect the cable wires to the screw terminals by
following the numbering ,Use wire size suitable to
the electric power input (see name plate on the unit)
and according to all current national safety code
requirements.
5. The cable connecting the outdoor and indoor units
must be suitable for outdoor use.
6. The plug must be accessible also after the appliance
has been installed so that it can be pulled out if nece-
ssary.
7. An efficient earth connection must be ensured.
8. If the power cable is damaged, it must be replaced by
an authorised Service Centre.
Front panel
Terminal block cover
wiring diagram
Note:The cable wires has been connected to the main
PCB of indoor unit by manufacturer according to the
model without terminal block
16
Installation of the mounting plate
Drilling a hole in the wall for the piping
Electrical connections---Indoor unit

INSTALLATION MANUAL---Installation of the Indoor unit
3
2
1
The piping can be run in the 3 directions indicated by
numbers in the picture . When the piping is run in
direction 1or3, cut a notch along the groove on the side
of the indoor unit with a cutter.
Run the piping in the direction of the wall hole and bind
the copper pipes , the drain pipe and the power cables
together with the tape with the drain pipe at the bottom,
so that water can flow freely.
Do not remove the cap from the pipe until connecting
it, to avoid dampness or dirt from entering.
If the pipe is bent or pulled too often , it will become
stiff . Do not bend the pipe more than three times at
one point.
When extending the rolled pipe, straighten the pipe by
unwinding it gently as shown in the picture.
1. Remove the indoor unit pipe cap (check that there is
no debris inside).
2. Insert the fare nut and create a flange at the extreme
end of the connection pipe.
3. Tighten the connections by using two wrenches
working in opposite directions torque wrench
Connecting the pipes
Indoor unit condensed water drainage
The indoor unit condensed water drainage is fundamen-
tal for the success of the installation.
1. Place the drain hose below the piping, taking care not
to create siphons.
2. The drain hose must slant downwards to aid drainage.
3. Do not bend the drain hose or leave it protruding or
twisted and do not put the end of it in water . If an
extension is connected to the drain hose , ensure that
it is lagged when it passes into the indoor unit.
4. If the piping is installed to the right, the pipes, power
cable and drain hose must be lagged and secured onto
the rear of the unit with a pipe connection.
1) Insert the pipe connection into the relative slot.
2) Press to join the pipe connection to the base.
YES
17
Refrigerant piping connection
Connections to the indoor unit
NO NO
NO
YES
Extending the rolled pipe
Shape the connection pipe

INSTALLATION MANUAL---Installation of the Indoor unit
INSTALLATION OF THE INDOOR UNIT
refrigerant
pipe
refrigerant
pipe
insulation
sleeve
connection
(for heat-pump)
cable 1
connection
cable
Probe
cable(for heat-pump) Condensed water
drain pipe
Covered by vinyl tape
After having connected the pipe according to the instruc-
tions, install the connection cables. Now install the drain
pipe. After connection,lag the pipe, cables and drain pipe
with the insulating material.
1. Arrange the pipes ,cables and drain hose well.
2. Lag the pipe joints with insulating material , securing
it with vinyl tape.
3. Run the bound pipe , Cables and drain pipe through
the wall hole and mount the indoor unit onto the upper
part of the mounting plate securely.
4. Press and push the lower part of the indoor unit tightly
against the mounting plate
mounting plate
INSTALLATION MANUAL---Installation of the outdoor unit
The outdoor unit should be installed on a solid wall
and fastened securely.
The following procedure must be observed before co-
nnecting the pipes and connecting cables : decide
which is the best position on the wall and leave enough
space to be able to carry out maintenance easily.
Fasten the support to the wall using screw anchors
which are particularly suited to the type of wall;
Use a larger quantity of screw anchors than normally
required for the weight they have to bear to aviod
vibration during operation and remain fastened in the
same position for years without the screws becoming
loose.
The unit must be installed following the national
regulations.
drain pipe
The condensed water and the ice formed in the outdoor
unit during heating operation can be drained away thro-
ugh the drain pipe
1. Fasten the drain port in the 25mm hole placed in the
part of the unit as shown in the picture.
2. Connect the drain port and the drain pipe.
Pay attention that water is drained in a suitable place.
18
Outdoor unit condensed water drainage
(only for heat pump models)
drain port