Murata R50E-15 User manual

Cat.No.R50E-15
Murata
Manufacturing Co., Ltd.
Trimmer Potentiometers/
Rotary Position Sensors
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.

CONTENTS
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Recycled Paper
1
2
3
4
5
6
7
8
9
10
Part Numbering 2
Selection Guide of Trimmer Potentiometers 4
SMD Open Type 2mm Size PVZ2/PVA2 Series 5
PVZ2/PVA2 Series Notice 9
SMD Open Type 3mm Size PVZ3 Series 11
PVZ3 Series Notice 15
SMD Sealed Type 2mm Size PVF2 Series 17
PVF2 Series Notice 19
SMD Sealed Type 3mm Size PVG3 Series 21
PVG3 Series Notice 24
SMD Sealed Type 4mm Size PVM4 Series 26
PVM4 Series Notice 28
SMD Sealed Type Multi-turn PVG5 Series 31
PVG5 Series Notice 33
Lead Sealed Type Single-turn PV32 Series 35
PV32 Series Notice 38
Lead Sealed Type Multi-turn PV12/PV37/PV36 Series 40
PV12/PV37/PV36 Series Notice 49
Rotary Position Sensors SMD/Lead Dust-proof Type 12mm Size SV01 Series 51
SV01 Series Notice 53
Rotary Position Sensors Connector Dust-proof Type SV21 Series 55
SV21 Series Notice 56
SMD Open Type (PVZ2/A2/Z3)/SMD Sealed Type (PVM4A_C01 Series) Specifications and Test Methods 57
SMD Sealed Type (PVF2/G3/M4A_D01/G5)/Lead Sealed Type (PV32/12/37/36) Specifications and Test Methods 58
Rotary Position Sensors SMD/Lead Dust-proof Type (SV01) Specifications and Test Methods 61
Rotary Position Sensors Connector Dust-proof Type (SV21) Specifications and Test Methods 62
Packaging 63
Recommended Adjustment Tools/Qualified Standards 67
1
2
3
4
5
6
7
8
9
10
• The RoHS compliance means that we judge from EU Directive 2002/95/EC the products do not contain lead, cadmium, mercury, hexavalent
chromium, PBB and PBDE, except exemptions stated in EU Directive 2002/95/EC annex and impurities existing in the natural world.
• This statement does not insure the compliance of any of the listed parts with any laws or legal imperatives developed by any EU members
individually with regards to the RoHS Directive.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2
oPart Numbering
qProduct ID
Trimmer Potentiometers
PV Trimmer Potentiometers
Product ID
(Part Number)
wSeries
eAdjustment Direction /Lead Type
Code Series Code Adjustment Direction/
Lead Type
Z2 SMD Open 2mm Size
Carbon Resistive Element
A2 SMD Open 2mm Size
A
R
Top
ATop
Rear
Z3
G3
F2
M4
G5
SMD Open 3mm Size
Carbon Resistive Element
SMD Sealed 4mm Size
32
Lead Sealed 6mm Round
Single-turn
12
Lead Sealed 7mm Round
4-turns
SMD Sealed 5mm Square
11-turns
SMD Sealed 3mm Size
SMD Sealed 2mm Size
A
A
A
A
A
H
H
P
R
N
T
S
H
P
T
S
G
K
Top
GTop
Top
Top
Top
Side
Top, Triangle
Top, Triangle
Top, Inline
Side, Triangle
Side, Triangle
Side, Triangle
Top, Triangle
Top, Triangle
Side, Triangle
Side, Triangle
Top, J-hook
Top, Gull-wing
Rear
KRear
RRear
36
37
Lead Sealed 10mm Square
25-turns
Lead Sealed 6mm Square
12-turns
W
Y
P
X
Z
W
Y
P
X
Z
Top, Inline
Top, Triangle
Side, Triangle
Side, Inline
Side, Triangle
Top, Triangle
Top, Inline
Side, Triangle
Side, Triangle
Side, Inline
rTotal Resistance
Expressed by three figures. The unit is ohm. The first and second
figures are significant digits, and the third figure expresses the
number of zeros which follow the two figures.
100
102
104
Ex.)
10Ω
1000Ω
100000Ω(=100kΩ)
Code Total Resistance
y
R00
e
A
t
A01
r
103
PV
qw
Z3
tIndividual Specification
Series Code Individual Specification Code
Standard Type
Standard Type (High-heat Resistance
Type/Ultra-thin Type)
PVA2
PVZ2
A01
C04
Standard Type (High-heat Resistance
Type/Top Adjustment)
High-heat Resistance Type
(for Rear Adjustment)
PVZ3
C01
E01
Standard Type
High-liability Type
PVM4 C01
D01
Standard Type (Resistance Change
Characteristics: Linear)
Standard Type (Resistance Change
Characteristics: Log Curve)
Standard Type (Resistance Change
Characteristics: Log Curve)
Standard Type (Resistance Change
Characteristics: Log-log Curve)
Standard Type (Resistance Change
Characteristics: Log-log Curve)
PVF2
A11
A41
A81
A51
A91
Standard Type
PV32/PV12 A01
Standard Type
Radial Taping
PV36/PV37 C01
C31
Standard Type
C01
PVG3/PVG5/
PV36/PV37
yPackaging
Ammo Pack
Bulk
Magazine
Reel
Code Packaging
A00
B00
M00*
R00
*M12 for PV36P Type and M15 for PV36W/Y/X/Z Type.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
3
Rotary Position Sensor
qProduct ID
(Part Number)
wSeries
eTerminal Shape
tRotor Hole Shape/Rotor Hole Size
rTotal Resistance
Expressed by three figures. The unit is ohm. The first and second
figures are significant digits, and the third figure expresses the
number of zeros which follow the two figures.
Ex.)
uPackaging
u
R00
e
A
y
A01
r
103
SV
q
AE
t
w
01
Product ID
SV Rotary Position Sensor
Code Series
01 Carbon Rotary Position Sensor
Code Terminal Shape
ASMD Type
LLead Type
Code Total Resistance
103 10000Ω(=10kΩ)
Code Rotor Hole Shape/Rotor Hole Size
AD D Hole/3.5mm Dia.
AE D Hole/4.0mm Dia.
CE T Hole/4.0mm Dia.
yIndividual Specification Code
Code Individual Specification Code
A01 SMD Type Standard
A11 Lead Type Standard
Code Packaging
B00 Bulk
R00 Reel
T00 Tray
qProduct ID
(Part Number)
wSeries
eTerminal Shape
tShaft Shape/Shaft Size
rElectrical Effective Rotational Angle
Expressed by three figures. The unit is degree. The first and
second figures are significant digits, and the third figure
expresses the number of zeros which follow the two figures.
Ex.)
uPackaging
u
B00
e
C
y
A01
r
201
SV
q
BJ
t
w
21
Product ID
SV Rotary Position Sensor
Code Series
21 Hole IC Rotary Position Sensor
Code Terminal Shape
CConnector Type
Code Electrical Effective Rotational Angle
201 200°
Code Shaft Shape/Shaft Size
BJ D Shaft/6.0mm Dia.
yIndividual Specification Code
Code Individual Specification Code
A01 Connector Type Standard
Code Packaging
B00 Bulk
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
4
Start
Mounting Method
Construction Adjustment
2mm size Single Turn
Surface Mount PCB Insertion
Sealed Construction
Top Side
Resistive Element Resistive Element
Cermet Resistive Element
SealedOpen
2mm size Single Turn
3mm size Single Turn
3mm size Single Turn
4mm size Single Turn
5mm size 11 Turns
6mm size Single Turn
7mm size 4 Turns
6mm size 12 Turns
6mm size Single Turn
7mm size 4 Turns
6mm size 12 Turns
10mm size 25 Turns 10mm size 25 Turns
2mm size Single Turn
Carbon Cermet Carbon Cermet
PVM4
PVG5
PV12H/P
PV37W/Y
PV12T/S
PV37P/X/Z
PV36W/Y PV36P/X/Z
Low Profile
(0.85mm max.)
PVZ2A_C04
Rear Adjustment
Low Profile with Smaller
FootPrint (0.9mm max.)
PVZ2R
with Rotational Stop
PVF2
for Automatic Adjustment
(0.9mm max.)
PVA2
for Automatic Adjustment
with Rotational Stop
PVG3A
with Rotational Stop
PVG3G
Rear Adjustment
with Rotational Stop
PVG3K
for Automatic Adjustment
PVZ3A
Top Adjustment
Low Profile (1.25mm max.)
PVZ3G
Rear Adjustment
PVZ3K
Rear Adjustment
Low Profile (1.5mm max.)
PVZ3R
with Rotational Stop
PV32H/P/R
with Rotational Stop
PV32N/S/T
Selection Guide of Trimmer Potentiometers
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

5
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Trimmer Potentiometers
SMD Open Type 2mm Size PVZ2/PVA2 Series
PVZ2 Series
2.1 0.8±0.05
0.5
0.4
0.45±0.1
0.8 2.4 Dia.
1.3 2.2
2.7±0.3
#2
0.7
#1 #3
∗1
∗1 Driver Plate Rotation Area:
Please do not place any components
more than 0.5mm in height within this area.
0.55 0.55
0.50.5
4 1
Soldering Part
(
Tolerance: ±0.2
)
in mm
#2
#1 #3
CLOCKWISE
PVZ2A
(
Tolerance : ±0.2
)
in mm
#2
#1 #3
CLOCKWISE
2.1
2.2
4.8
0.6 0.650.65
(0.6)(0.6)
0.8 0.8+0.10
- 0.15
1.3
0.45±0.10
Soldering
Part
#2
#1 #3
2.4 Dia.
∗1: Driver Plate Rotation Area
*1
PVZ2R
Part Number Power Rating
(W) Soldering Method Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/°C)
PVZ2p471C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 470ohm ±30% ±500
PVZ2p681C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 680ohm ±30% ±500
PVZ2p102C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 1k ohm ±30% ±500
PVZ2p152C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 1.5k ohm ±30% ±500
PVZ2p222C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 2.2k ohm ±30% ±500
PVZ2p332C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 3.3k ohm ±30% ±500
PVZ2p472C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 4.7k ohm ±30% ±500
PVZ2p682C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 6.8k ohm ±30% ±500
PVZ2p103C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 10k ohm ±30% ±500
PVZ2p153C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 15k ohm ±30% ±500
PVZ2p223C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 22k ohm ±30% ±500
PVZ2p303C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 30k ohm ±30% ±500
PVZ2p333C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 33k ohm ±30% ±500
PVZ2p473C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 47k ohm ±30% ±500
PVZ2p503C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 50k ohm ±30% ±500
PVZ2p683C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 68k ohm ±30% ±500
PVZ2p104C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 100k ohm ±30% ±500
PVZ2p154C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 150k ohm ±30% ±500
PVZ2p204C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 200k ohm ±30% ±500
PVZ2p224C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 220k ohm ±30% ±500
PVZ2p304C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 300k ohm ±30% ±500
Continued on the following page.
■ Features
1. Ultra-small and thin external dimensions of
2.1(W)x2.7(L)x0.85 max. (T)mm.
(Top adjustment type: PVZ2A_C04 Series)
2. Ultra-small and thin external dimensions of
2.1(W)x4.8(L)x0.9 max. (T)mm.
(Rear adjustment type: PVZ2R_C04 Series)
Compact PCB design is possible by smaller
adjustment hole (3.0mm dia.) due to short wing
length (4.8mm).
3. Au plated termination achieves a high density
PCB mounting.
4. Cross-shaped driver slot allows for in-process
automatic adjustment and it provides superior
adjustability.
5. Two-piece parts construction achieves low cost and
excellent quality.
6. Special resin substrate allows high peak temperature
for reflow soldering (PVZ2_Cxx Series).
7. Complies with RoHS directive.
■ Applications
1. Pick-up module 2. LCD
3. Cellular-phone 4. PHS
5. Pager 6. DVC
7. Digital camera 8. Portable audio, etc.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

6
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Part Number Power Rating
(W) Soldering Method Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/°C)
Continued from the preceding page.
PVZ2p334C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 330k ohm ±30% ±500
PVZ2p474C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 470k ohm ±30% ±500
PVZ2p504C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 500k ohm ±30% ±500
PVZ2p684C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 680k ohm ±30% ±500
PVZ2p105C04 0.1(50°C) Reflow/Soldering Iron 1(240°±10°) 1M ohm ±30% ±500
Operating Temperature Range: -25 to 85 °C
The blank column is filled with the code of adjustment direction and lead type A (top) or R (rear).
■ Construction
PVZ2A
■ Standard Land Pattern
PVZ2A
0.9
0.6 0.60.7
1.55 1.55
0.85 0.85
(
Tolerance : ±0.1
in mm
)
■ Construction
PVZ2R
Driver Plate
Wiper
Resistive
Element
Resin Substrate
#2-Terminal
#3-Terminal
#1-Terminal
■ Standard Land Pattern
PVZ2R
3.0 Dia.
0.6
0.9
0.60.6
2.52.5
0.70.7
(
Tolerance : ±0.1
)
in mm
■ Characteristics Res. Change: +10, -2%
Res. Change: R
<
50kohm···+2, -10%
50kohm<R···+2, -15%
Res. Change: ±10%
Res. Change: R
<
50kohm···+2, -10%
50kohm<R···+2, -15%
Res. Change: ±5%
Res. Change: ±10% (10 cycles)
Humidity Exposure
High Temperature
Exposure
Humidity Load Life
Load Life
Temperature Cycle
Rotational Life
=
=
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

7
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
PVA2 Series
■ Features
1. Ultra-small and thin external dimensions of
2.2(W)x2.75(L)x0.90 max.(T)mm.
2. For the terminal attachment method of construction
which uses neither solder nor adhesives, good
solderability and terminal attachment intensity
are realized.
3. Because of multi-contact wiper structure, PVA2 has
a stable characteristics (low noise).
4. PVA2 series do not use a solder, flux and cleaning
solvent, so they are environmentally friendly
products.
5. Heat resistance performance enables high temperature
peak re-flow soldering.
6. PVA2 series comply with RoHS directive.
■ Applications
1. Thin-model optical pick-up module
2. LCD module
3. Optical communication module
4. Small sensor module
5. Digital camera
6. Small telecommunicaions equipment, etc.
2.2
1.3 0.45±0.1
0.8
0.8±0.1
0.4
0.5 0.6
0.5
2.75
1.3
0.9 0.6
0.75
#1
#2
#3
Resin
2.4 Dia
#2 (Wiper Contact)
#1 #3
CIRCUIT
CLOCKWISE
(
Tolerance: ±0.2
)
in mm
Part Number Power Rating
(W) Soldering Method Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/°C)
PVA2A101A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 100ohm ±25% ±250
PVA2A151A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 150ohm ±25% ±250
PVA2A221A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 220ohm ±25% ±250
PVA2A331A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 330ohm ±25% ±250
PVA2A471A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 470ohm ±25% ±250
PVA2A681A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 680ohm ±25% ±250
PVA2A102A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 1k ohm ±25% ±250
PVA2A152A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 1.5k ohm ±25% ±250
PVA2A222A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 2.2k ohm ±25% ±250
PVA2A332A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 3.3k ohm ±25% ±250
PVA2A472A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 4.7k ohm ±25% ±250
PVA2A682A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 6.8k ohm ±25% ±250
PVA2A103A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 10k ohm ±25% ±250
PVA2A153A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 15k ohm ±25% ±250
PVA2A223A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 22k ohm ±25% ±250
PVA2A333A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 33k ohm ±25% ±250
PVA2A473A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 47k ohm ±25% ±250
PVA2A683A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 68k ohm ±25% ±250
PVA2A104A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 100k ohm ±25% ±250
PVA2A154A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 150k ohm ±25% ±250
PVA2A224A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 220k ohm ±25% ±250
PVA2A334A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 330k ohm ±25% ±250
PVA2A474A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 470k ohm ±25% ±250
PVA2A684A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 680k ohm ±25% ±250
PVA2A105A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 1M ohm ±25% ±250
PVA2A155A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 1.5M ohm ±25% ±250
PVA2A225A01 0.1(70°C) Reflow/Soldering Iron 1(260°±10°) 2.2M ohm ±25% ±250
Operating Temperature Range: -55 to 125 °C
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

8
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Construction
Driver Plate
Resistive Element
Ceramic Substrate
#3-Terminal
#1-Terminal
Wiper
#2-Terminal
■ Standard Land Pattern
(
Tolerance : ±0.1
)
in mm
1.1
0.70
1.90
0.850.90
1.551.70
■ Characteristics Res. Change: ±3%
Res. Change: ±3%
Res. Change: ±3%
Res. Change: ±3%
Res. Change: ±3%
Res. Change: ±10% (10 cycles)
Humidity Exposure
High Temperature
Exposure
Humidity Load Life
Load Life
Temperature Cycle
Rotational Life
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

PVZ2/PVA2 Series Notice
9
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Notice (Operating and Storage Conditions)
■ Notice (Rating)
1. When using with partial load (rheostat), minimize
the power depending on the resistance value.
2. The maximum input voltage to a trimmer
potentiometer should not exceed (P•R)^1/2 or the
maximum operating voltage, whichever is smaller.
3. If the trimmer potentiometer is used in DC and high
humidity conditions, please connect wiper (#2) for
plus and resistive element (#1 or #3) for minus.
(PVZ Series only)
■ Notice (Soldering and Mounting)
1. Store in temperatures of -10 to +40 deg. C and
relative humidity of 30-85%.
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
the following environmental conditions:
(1) Corrosive gaseous atmosphere
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(2) In liquid
(Ex. Oil, Medical liquid, Organic solvent, etc.)
(3) Dusty/dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
1. Soldering
(1) Reflow soldering method and soldering iron are
available. Cannot be soldered using the flow
soldering method (dipping). If you use the flow
soldering method, the trimmer potentiometer may
not function.
(2) Use our standard land dimension. Excessive land
area causes displacement due to the effect of
the surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
(3) Soldering condition
Refer to the temperature profile.
If the soldering conditions are not suitable,
e.g., excessive time and/or excessive
temperature, the trimmer potentiometer may
deviate from the specified characteristics.
(4) Apply the appropriate amount of solder paste.
The thickness of solder paste should be printed
from 100 micro m to 150 micro m and the
dimension of land pattern used should be Murata's
standard land pattern at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals.
(5) The soldering iron should not come in contact
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
2. Mounting
(1) Do not apply excessive force, preferably 4.9N
max. (Ref. 500gf) when the trimmer
potentiometer is mounted to the PCB.
(2) Do not warp and/or bend PC board to prevent
trimmer potentiometer from breakage.
(3) In chip placers, the recommended size of the
cylindrical pick-up nozzle should be outer
dimension 1.5-1.8mm dia. and inner dimension
1.3mm dia.
3. Cleaning
(1) In case there is flux on the resistive element,
clean sufficiently with cleaning solvents and
completely remove all residual flux.
(2) Isopropyl-alcohol and Ethyl-alcohol are
applicable solvents for cleaning. If you use any
other types of solvents, please evaluate
performance with your product.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

PVZ2/PVA2 Series Notice
10
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Soldering Profile
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
Time (s)
t1
1. Soldering profile for Lead-free solder (96.5Sn/3.0Ag/0.5Cu)
Standard Profile
Pre-heating Heating Cycle of
Reflow
Time°C
Series
PVA2
PVZ2****C**
Temp. (T1)
°C
Time (t1)
sec.
Temp. (T2)
°C
Time (t2)
sec.
Pre-heating Heating Cycle of
Reflow
Time°C
Temp. (T1)
°C
Time (t1)
sec.
Temp. (T4)
°C
Time (t3)
sec.
Limit Profile
2
2
245±3
245±3
150 to 180
150 to 180
60 to 120
60 to 120
220
220
30 to 60
30 to 60
2
2
260 +5/-0
260
150 to 180
150 to 180
60 to 120
60 to 120
220
220
30 to 60
30 to 60
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating Cycle of
Reflow
Time°C
Series
PVA2
PVZ2****C**
Temp. (T1)
°C
Time (t1)
sec.
Temp. (T2)
°C
Time (t2)
sec.
1230
150 60 to 120 183 30
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
2. Soldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to 1)
Standard Condition
Series
PVA2
PVZ2****C**
Temperature of Soldering Iron Tip Soldering Time Soldering Iron Power Output
350±10 3 max. 30 max. 1
Cycle of Soldering Iron
°C sec. W Time
Reflow Soldering Profile
Soldering Iron
Peak
Temperature
(T3)
Peak
Temperature
(T5)
Peak
Temperature
(T3)
■ Notice (Handling)
1. Use suitable screwdrivers that fit comfortably in
driver slot. We recommend the screwdriver below.
* Recommended screwdriver for manual adjustment
Murata P/N: KMDR190
2. The screwdriver should be set in the products
vertically, do not apply more than 4.9N (Ref. 500gf)
of twist and stress after mounting onto PCB to
prevent contact intermittence. If excessive force is
applied, the trimmer potentiometer may not function.
3. Please use within the effective rotational angle.
The trimmer potentiometer does not have a
mechanical stop for over rotation. In cases out of
effective rotational angle, the trimmer
potentiometer may not function.
4. When using a lock paint to fix slot position or
cover the rotor, please evaluate performance with
your product. Lock paint may cause corrosion or
electrical contact problems.
■ Notice (Other)
1. Please make sure that your product has been
evaluated and confirmed against your
specifications when our product is mounted to your
product.
2. Murata cannot guarantee trimmer potentiometer
integrity when used under conditions other than
those specified in this document.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

11
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Trimmer Potentiometers
SMD Open Type 3mm Size PVZ3 Series
PVZ3 Series
#2
#1 #3
CLOCKWISE
#1
#2
#3
3.1
1.0
0.75 1.0 0.75
2.4±0.1
3.2 3.6
0.5±0.1
1.15 Dia.
2.2 Dia.
3.0 Dia.
1.85±0.1
0.25±0.1 0.1 max.
0.70.7
(
Tolerance: ±0.3
)
in mm
PVZ3A
3.1
3.1
0.8
#2
#1 #3
0.55 0.55
1.15±0.10
1.2
3.6
0.4
0.6
0.55
R1.5
2.1±0.1
0.5±0.1
R0.75
#2 (Wiper Contact)
#1 #3
CLOCKWISE
CIRCUIT
(
Tolerance: ±0.3
in mm
)
PVZ3G
#1#3
3.1 1.85±0.1
2.1
0.25±0.1
3.2
0.5±0.1
5.4 4.4
2.4±0.1
#2
0.85
1.1
0.9 0.85
1.15 Dia.
3.0 Dia.
2.2 Dia.
Soldering Part
#2 (Wiper Contact)
#1 #3
CIRCUIT
CLOCKWISE
(
Tolerance: ±0.3
)
in mm
PVZ3K
#1#3
3.1 1.4±0.1 0.4±0.1
3.2
0.5±0.1
0.50.5
5.8
2.4±0.1
#2
0.85
1.1
0.9 0.85
1.15 Dia.
3.0 Dia.
2.2 Dia.
Soldering Part
#2 (Wiper Contact)
#1 #3
CIRCUIT
CLOCKWISE
(
Tolerance: ±0.3
)
in mm
PVZ3R
■ Features
1. Excellent solderability characteristics are
achieved via special plating techniques on each
termination.
2. Specially designed substrate prevents wicking of
flux onto the top of the part body.
3. Funnel shaped adjustment slot allows for in-process
automatic adjustment. (PVZ3A/PVZ3K/PVZ3R Series)
4. High-heat resistance type is available
(PVZ3A_C01/PVZ3K_E01/PVZ3R_E01).
5. Enlarged bottom termination enhances soldering
strength while reducing the necessary land area
required promoting high-density PCB mounting
(PVZ3A/PVZ3G Series).
6. Low profile rear adjustment type (PVZ3R Series)
realizes 1.5mm max. height by infilling driver
plate into through-hole of PCB.
7. The standard position of driver plate is adjusted
at the center normally, but another position is
also available.
8. This product meets PB-free standards.
9. Complies with RoHS directive.
■ Applications
1. Optical pick up 2. Cordless telephones
3. CD players 4. FDD
5. Motor 6. CD-ROMs
7. Car stereos 8. TFT-LCD TV sets
9. Headphone stereos
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

12
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Part Number Power Rating
(W) Soldering Method Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/°C)
PVZ3p221C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 220ohm ±30% ±500
PVZ3p331C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 330ohm ±30% ±500
PVZ3p471C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 470ohm ±30% ±500
PVZ3p681C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 680ohm ±30% ±500
PVZ3p102C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 1k ohm ±30% ±500
PVZ3p152C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 1.5k ohm ±30% ±500
PVZ3p222C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 2.2k ohm ±30% ±500
PVZ3p332C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 3.3k ohm ±30% ±500
PVZ3p472C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 4.7k ohm ±30% ±500
PVZ3p682C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 6.8k ohm ±30% ±500
PVZ3p103C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 10k ohm ±30% ±500
PVZ3p153C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 15k ohm ±30% ±500
PVZ3p223C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 22k ohm ±30% ±500
PVZ3p333C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 33k ohm ±30% ±500
PVZ3p473C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 47k ohm ±30% ±500
PVZ3p683C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 68k ohm ±30% ±500
PVZ3p104C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 100k ohm ±30% ±500
PVZ3p154C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 150k ohm ±30% ±500
PVZ3p224C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 220k ohm ±30% ±500
PVZ3p334C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 330k ohm ±30% ±500
PVZ3p474C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 470k ohm ±30% ±500
PVZ3p684C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 680k ohm ±30% ±500
PVZ3p105C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 1M ohm ±30% ±500
PVZ3p155C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 1.5M ohm ±30% ±500
PVZ3p225C01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 2.2M ohm ±30% ±500
PVZ3p221E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 220ohm ±30% ±500
PVZ3p331E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 330ohm ±30% ±500
PVZ3p471E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 470ohm ±30% ±500
PVZ3p681E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 680ohm ±30% ±500
PVZ3p102E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 1k ohm ±30% ±500
PVZ3p152E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 1.5k ohm ±30% ±500
PVZ3p222E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 2.2k ohm ±30% ±500
PVZ3p332E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 3.3k ohm ±30% ±500
PVZ3p472E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 4.7k ohm ±30% ±500
PVZ3p682E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 6.8k ohm ±30% ±500
PVZ3p103E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 10k ohm ±30% ±500
PVZ3p153E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 15k ohm ±30% ±500
PVZ3p223E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 22k ohm ±30% ±500
PVZ3p333E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 33k ohm ±30% ±500
PVZ3p473E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 47k ohm ±30% ±500
PVZ3p683E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 68k ohm ±30% ±500
PVZ3p104E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 100k ohm ±30% ±500
PVZ3p154E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 150k ohm ±30% ±500
PVZ3p224E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 220k ohm ±30% ±500
PVZ3p334E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 330k ohm ±30% ±500
PVZ3p474E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 470k ohm ±30% ±500
PVZ3p684E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 680k ohm ±30% ±500
PVZ3p105E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 1M ohm ±30% ±500
PVZ3p155E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 1.5M ohm ±30% ±500
PVZ3p225E01 0.1(50°C) Reflow/Soldering Iron 1(230°±10°) 2.2M ohm ±30% ±500
Operating Temperature Range: -25 to 85 °C
The blank column is filled with the code of adjustment direction and lead type A (top adjustment), G (top adjustment and thin type),
K (rear adjustment) or R (rear adjustment and thin type).
A and G are only for C01.
K and R are only for E01.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

13
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Construction
PVZ3A
■ Construction
PVZ3G
Driver Plate Wiper
Resistive
Element
Resin Substrate
#2-Terminal
#3-Terminal
#1-Terminal
■ Construction
PVZ3K Driver Plate
Wiper
Resistive Element
(Carbon)
Resin Substrate
#2-Terminal
#3-Terminal
#1-Terminal
■ Standard Land Pattern
PVZ3K
1.5
1.04.01.0
0.5
3.0
3.0 Dia
Tolerance : ±0.1
(
in mm
)
■ Construction
PVZ3R
Driver Plate
Wiper
Resistive Element
(Carbon)
Resin Substrate
#2-Terminal
#3-Terminal
#1-Terminal
■ Standard Land Pattern
PVZ3R
1.25
4.0 Dia.
1.25
3.0
1.5
0.70.7
3.13.1
Tolerance : ±0.1
(
in mm
)
Continued on the following page.
■ Standard Land Pattern
PVZ3A/PVZ3G
1.1
0.9
1.91.9
0.9
1.0 0.7 1.0 Tolerance : ±0.1
(
in mm
)
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

14
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
■ Characteristics Res. Change: +10, -2%
Res. Change: R
<
100kohm···+2, -10%
100kohm<R···+2, -15%
Res. Change: ±10%
Res. Change: R
<
100kohm···+2, -10%
100kohm<R···+2, -15%
Res. Change: ±5%
Res. Change: ±10% (10 cycles)
Humidity Exposure
High Temperature
Exposure
Humidity Load Life
Load Life
Temperature Cycle
Rotational Life
=
=
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

PVZ3 Series Notice
15
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Notice (Operating and Storage Conditions)
1. Store in temperatures of -10 to +40 deg. C and
relative humidity of 30-85%.
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
the following environmental conditions:
(1) Corrosive gaseous atmosphere
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(2) In liquid
(Ex. Oil, Medical liquid, Organic solvent, etc.)
(3) Dusty/dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
1. Soldering
(1) Soldering conditions
Refer to the temperature profile.
If the soldering conditions are not suitable,
e.g., excessive time and/or excessive
temperature, the trimmer potentiometer may
deviate from the specified characteristics.
Do not use flow soldering method (dipping).
If you use the flow soldering method, the
trimmer potentiometer may not function.
(2) Use our standard land dimension. Excessive land
area causes displacement due to the effect of
the surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
(3) Apply the appropriate amount of solder paste.
The thickness of solder paste should be printed
from 100 micro m to 150 micro m and the dimension
of land pattern used should be Murata's standard
land pattern at reflow soldering. Insufficient
amounts of solder can lead to insufficient
soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals.
(4) The soldering iron should not come in contact with
the case of the trimmer potentiometer. If such
contact does occur, the trimmer potentiometer
may be damaged. (PVZ Series only)
2. Mounting
(1) Do not apply excessive force, preferably 4.9N
max. (Ref. 500gf) when the trimmer potentiometer
is mounted to the PCB.
(2) Do not warp and/or bend PC board to prevent
trimmer potentiometer from breakage.
(3) In chip placers, the recommended size of the
cylindrical pick-up nozzle should be outer
dimension 2.5-2.8mm dia. and inner dimension
2mm dia.
3. Cleaning
(1) In case there is flux on the resistive element,
clean sufficiently with cleaning solvents and
completely remove all residual flux.
(2) Isopropyl-alcohol and Ethyl-alcohol are
applicable solvents for cleaning. If you use any
other types of solvents, please evaluate
performance with your product.
■ Notice (Rating)
1. When using with partial load (rheostat), minimize
the power depending on the resistance value.
2. The maximum input voltage to a trimmer
potentiometer should not exceed (P•R)^1/2 or the
maximum operating voltage, whichever is smaller.
3. If the trimmer potentiometer is used in DC and high
humidity conditions, please connect wiper (#2) for
plus and resistive element (#1 or #3) for minus.
■ Notice (Soldering and Mounting)
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

PVZ3 Series Notice
16
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Soldering Profile
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
Time (s)
t1
1. Soldering profile for Lead-free solder (96.5Sn/3.0Ag/0.5Cu)
Standard Profile
Pre-heating Heating Cycle of
Reflow Cycle of Reflow
Time°C
Series
PVZ3A***C01
PVZ3G***C01
PVZ3K***E01
PVZ3R***E01
Temp. (T1)
°C
Time (t1)
sec.
Temp. (T2)
°C
Time (t2)
sec.
Pre-heating Heating
Time°C
Temp. (T1)
°C
Time (t1)
sec.
Temp. (T4)
°C
Time (t3)
sec.
Limit Profile
2
2
2
2
245±3
245±3
245±3
245±3
150 to 180
150 to 180
150 to 180
150 to 180
60 to 120
60 to 120
60 to 120
60 to 120
220
220
220
220
30 to 60
30 to 60
30 to 60
30 to 60
2
2
2
2
260
260
260
260
150 to 180
150 to 180
150 to 180
150 to 180
60 to 120
60 to 120
60 to 120
60 to 120
220
220
220
220
30 to 60
30 to 60
30 to 60
30 to 60
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating
Series
PVZ3A***C01
PVZ3G***C01
PVZ3K***E01
PVZ3R***E01
Temp. (T1)
°C
Time (t1)
sec.
Temp. (T2)
°C
Time (t2)
sec.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
2. Soldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to 1)
Standard Condition
Series
PVZ3A***C01
PVZ3G***C01
PVZ3K***E01
PVZ3R***E01
Temperature of Soldering Iron Tip Soldering Time Soldering Iron Power Output
350±10 3 max. 30 max. 1
Cycle of Solder Iron
°C sec. W Time
Reflow Soldering Profile
Peak
Temperature
(T3)
Peak
Temperature
(T5)
Cycle of
Reflow
Time°C
1230 max.150 60 to 120 183 30
Peak
Temperature
(T3)
Soldering Iron
■ Notice (Handling)
1. Use suitable screwdrivers that fit comfortably in
driver slot. We recommend the screwdrivers below.
* Recommended screwdriver for manual adjustment
>VESSEL MFG.: NO.9000+1.7x30
(Murata P/N: KMDR080)
* Recommended screwdriver for automatic adjustment
>TORAY MFG.: JB-2225 (Murata P/N: KMBT070)
We can supply the screwdrivers above.
If you place order, please specify the Murata P/N.
2. The screwdriver should be set in the products
vertically, do not apply more than 4.9N (Ref. 500gf)
of twist and stress after mounting onto PCB to
prevent contact intermittence. If excessive force is
applied, the trimmer potentiometer may not function.
3. Please use within the effective rotational angle.
Do not have a mechanical stop for over rotation.
In cases out of effective rotational angle, the
trimmer potentiometer may not function.
4. When using a lock paint to fix slot position or
cover the rotor, please evaluate performance with
your product. Lock paint may cause corrosion or
electrical contact problems.
■ Notice (Other)
1. Please make sure that your product has been
evaluated and confirmed against your
specifications when our product is mounted to your
product.
2. Murata cannot guarantee trimmer potentiometer
integrity when used under conditions other than
those specified in this document.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

17
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Trimmer Potentiometers
SMD Sealed Type 2mm Size PVF2 Series
■ Features
1. Ultra-compact size of "2x2x2.3mm"
2. A sealed structure prevents liquids (water,
cleaning liquid, sweat, etc.) from entering.
3. As for the resistance change characteristics, both
a log curve type and linear type are available.
4. A rotation service life of 100 cycles is guaranteed.
5. Can be automatically mounted using a chip placer,
as well as mounted using reflow soldering.
6. Complies with RoHS directive.
■ Applications
1. Hearing aids
2. Ultra-compact sensors
3. Applications requiring ultra-compactness, and a
sealed structure
Marking 2.00
#2
#1 #3
1.6Dia.
2.00 0.30
2.15max.
2.30±0.15
0.70±0.15
0.70±0.15
0.30±0.15
0.50
0.30 0.50
0.30
0.50
#2 (Wiper contact)
#1 #3
Clockwise
CIRCUIT Tolerance : ±0.10
(
in mm
)
Part Number Power Rating
(W) Soldering Method Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/°C)
PVF2A501A11 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 500ohm ±30% ±500
PVF2A102A11 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 1k ohm ±30% ±500
PVF2A202A11 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 2k ohm ±30% ±500
PVF2A502A11 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 5k ohm ±30% ±500
PVF2A103A11 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 10k ohm ±30% ±500
PVF2A203A11 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 20k ohm ±30% ±500
PVF2A503A11 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 50k ohm ±30% ±500
PVF2A104A11 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 100k ohm ±30% ±500
PVF2A204A11 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 200k ohm ±30% ±500
PVF2A504A11 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 500k ohm ±30% ±500
PVF2A105A11 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 1M ohm ±30% ±500
PVF2A102A41 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 1k ohm ±30% ±500
PVF2A202A41 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 2k ohm ±30% ±500
PVF2A502A41 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 5k ohm ±30% ±500
PVF2A103A41 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 10k ohm ±30% ±500
PVF2A203A41 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 20k ohm ±30% ±500
PVF2A503A41 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 50k ohm ±30% ±500
PVF2A104A41 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 100k ohm ±30% ±500
PVF2A204A41 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 200k ohm ±30% ±500
PVF2A504A41 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 500k ohm ±30% ±500
PVF2A102A51 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 1k ohm ±30% ±500
PVF2A202A51 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 2k ohm ±30% ±500
PVF2A502A51 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 5k ohm ±30% ±500
PVF2A103A51 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 10k ohm ±30% ±500
PVF2A203A51 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 20k ohm ±30% ±500
PVF2A503A51 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 50k ohm ±30% ±500
PVF2A104A51 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 100k ohm ±30% ±500
PVF2A204A51 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 200k ohm ±30% ±500
PVF2A504A51 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 500k ohm ±30% ±500
PVF2A102A81 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 1k ohm ±30% ±500
PVF2A202A81 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 2k ohm ±30% ±500
PVF2A502A81 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 5k ohm ±30% ±500
PVF2A103A81 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 10k ohm ±30% ±500
Continued on the following page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

18
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Part Number Power Rating
(W) Soldering Method Number of Turns (Effective Rotation Angle) Total Resistance Value TCR (ppm/°C)
Continued from the preceding page.
PVF2A203A81 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 20k ohm ±30% ±500
PVF2A503A81 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 50k ohm ±30% ±500
PVF2A104A81 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 100k ohm ±30% ±500
PVF2A204A81 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 200k ohm ±30% ±500
PVF2A504A81 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 500k ohm ±30% ±500
PVF2A102A91 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 1k ohm ±30% ±500
PVF2A202A91 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 2k ohm ±30% ±500
PVF2A502A91 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 5k ohm ±30% ±500
PVF2A103A91 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 10k ohm ±30% ±500
PVF2A203A91 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 20k ohm ±30% ±500
PVF2A503A91 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 50k ohm ±30% ±500
PVF2A104A91 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 100k ohm ±30% ±500
PVF2A204A91 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 200k ohm ±30% ±500
PVF2A504A91 0.001(50°C) Reflow/Soldering Iron 1(210°±10°) 500k ohm ±30% ±500
Operating Temperature Range: -25 to 60 °C
The last three digits express the individual specification codes for Resistance Curve. Please refer to Resistance Curve on the following page for characteristics.
■ Construction ■ Standard Land Pattern
■ Characteristics
Linear-log. curve (Measured from terminal 1 to 2)
100
90
80
70
60
50
40
30
20
10
00
#1 20 40 60 80 100 #3
Percent clockwise rotation (%)
Percent resistance (%)
A11
A81
A41
Linear-log. log. curve (Measured from terminal 2 to 3)
100
90
80
70
60
50
40
30
20
10
00
#1 20 40 60 80 100 #3
Percent clockwise rotation (%)
Percent resistance (%)
A11
A91
A51
∆TR : ±5%
∆TR : ±15, -2%
∆V.S.S.: ±5%
∆V.S.S.: ±5%
∆TR : +2, -10%
∆TR : ±3%
∆TR : ±10% (100 cycles)
Temperature Cycle
Humidity
Vibration
Shock (100G)
Temperature Load Life
Low Temperature Exposure
Rotational Life ∆TR : Total Resistance Change
∆V.S.S.: Voltage Setting Stability
■ Resistance Curve
O-ring
Rotor
Terminal
Shaft
Case
Substrate
Wiper
Resistive Element
0.60
0.900.90
2.20
0.60 0.60
0.40
Tolerance : ±0.10
(
in mm
)
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

PVF2 Series Notice
19
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Notice (Operating and Storage Conditions)
1. Soldering
(1) Soldering conditions
Refer to the temperature profile.
If the soldering conditions are not suitable,
e.g., excessive time and/or excessive
temperature, the trimmer potentiometer may
deviate from the specified characteristics.
(2) Use our standard land dimension. Excessive land
area causes displacement due to the effect of
the surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
(3) The soldering iron should not come in contact
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
(4) Cannot be soldered using the flow soldering
method. If you use the flow soldering method,
the trimmer potentiometer may not function.
2. Mounting
(1) Use our standard land dimension. Excessive land
area causes displacement due to the effect of
the surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
(2) Do not apply excessive force, preferably 4.9N
max. (Ref. 500gf) when the trimmer potentiometer
is mounted to the PCB.
(3) Do not warp and/or bend PC board to prevent
trimmer potentiometer from breakage.
3. Cleaning
Isopropyl-alcohol and Ethyl-alcohol are applicable
solvents for cleaning. If you use any other types
of solvents, please consult with a Murata factory
representative prior to using.
1. Store in temperatures of -10 to +40 deg. C and
relative humidity of 30-85%.
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
the following environmental conditions:
(1) Corrosive gaseous atmosphere
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(2) In liquid
(Ex. Oil, Medical liquid, Organic solvent, etc.)
(3) Dusty/dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
■ Notice (Rating)
1. When using with partial load (rheostat), minimize
the power depending on the resistance value.
2. The maximum input voltage to a trimmer
potentiometer should not exceed (P•R)^1/2 or the
maximum operating voltage, whichever is smaller.
3. If the trimmer potentiometer is used in DC and high
humidity conditions, please connect wiper (#2) for
plus and resistive element (#1 or #3) for minus.
■ Notice (Soldering and Mounting)
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R50E.pdf
07.3.20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.