Muscle Rack GRW60 - 4 Operator's manual

Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a
possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not
included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY
PART OF THE UNIT, OR USE IT AS A LADDER. DO NOT OVERLOAD. Evenly distribute the weight on each level
and always keep the heavier loads on the bottom. Use care when working with metal parts.
Boltless
Steel Shelving
MODEL NUMBER
GRW60 - 4
D - Woodboard Shelf
C - Post
E - Post Coupler
GRW60
GRW60
GRW60 -
-
-4 4 Shelf
4 4 Shelf
4 4 Shelf -
-
-60”h x 18”d x 36”w
60”h x 18”d x 36”w
60”h x 18”d x 36”w
Description
A - Beams
B - Braces
C - Post
D - Woodboard
E - Coupler
Qty.
8
8
8
4
8
Part Number
HMBE 3403
HMBE 1603
HMPT 3003
RPBSR100
HIPC 0200
Part Size
34 7/8”
16 27/32”
30”
18” x 36”
2 1/2” x 7/8”
General Instructions
General Instructions
General Instructions
Assembly is done with the tabs of the beams and braces fitting into the slots of the post. A rubber mallet may be used
on the beams and braces to seat the tabs properly. A hammer can also be used, providing one uses a cloth or a block
of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the tabs are straight and
fully engaged.
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel
free to contact our Muscle Rack manufacturing facility at, [phone] and request customer service.
We can also be reached on the internet at the following email address : [email protected].
To obtain replacement parts, please provide the following information :
- Model # - Part # & Description - Location Purchased - Date Purchased
Consumer Products Division
Edsal Manufacturing Company
4400 South Packers Avenue
Chicago, IL 60609 www.edsal.com
Tools Necessary For Assembly
Tools Necessary For Assembly
Tools Necessary For Assembly
Rubber Mallet
Note: TAP GENTLY ! A Hammer could be used
with a cloth or a wood block to protect the parts.
A - Beams
B - Braces
Medium Duty Steel Shelving

Assemble two (2) post with one (1) brace (see figure A). The
flat angled edge of the brace be facing up. Skipping one (1)
slot from the bottom, slide the tabs of the brace into the slots of
the post and tap down gently to properly seat (see figure B).
Repeat this process using two (2) post and one (1) brace.
Attach the assembled end units with two (2) beams (see figure
C). Again Skipping one (1) slot from the bottom, slide tabs of
the beams into post slots and tap down gently to properly seat.
Assembly Instructions for GRW60
Assembly Instructions for GRW60
Assembly Instructions for GRW60 -
-
-4
4
4
Start by adding a woodboard shelf to the level previously built,
then continue working by adding the second level using two (2)
beams and two (2) braces in the post slots of your desired
location. Again slide the tabs of the beams and braces into the
post slots and tap gently to properly seat.
IMPORTANT NOTE : Make sure all beams and braces are fully seated into the post slots.
IMPORTANT NOTE : Make sure all beams and braces are fully seated into the post slots.
IMPORTANT NOTE : Make sure all beams and braces are fully seated into the post slots.
Add a woodboard shelf to the previously built level, then as-
semble the top post to the bottom post by using eight (8) of
the post couplers. Slide the couplers tabs into the top of the
bottom post, tap gently to properly seat. Slide the top post
onto the remaining tabs of the couplers, tap the top post down
to properly seat (see figure D). Install the third level above the
post couplers, using two (2) beams, and two (2) braces.
Add a woodboard shelf to the previously built level, then con-
tinue by adding the final level to the unit using two (2) beams
and two (2) braces. Tap gently to properly seat and add the
final woodboard shelf to the top of the unit.
Step
1
Step
2
Step
3
Step
4
Figure A
Figure B
Figure C
Tap Lightly
Post Slot
Brace
Beam
Woodboard Shelf
Figure D
Woodboard Shelf
Post Coupler
Top Post
Bottom Post
Woodboard Shelf