Muscle Rack MR3600 User manual

Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a
possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not
included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY
PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the
heavier loads on the bottom. Use care when working with metal parts.
5 Shelf Storage Unit
With Enclosure
MODEL NUMBER
MR3600
MR3600 5 Shelf With Enclosure
MR3600 5 Shelf With Enclosure
MR3600 5 Shelf With Enclosure -
-
-72”h x 18”d x 36”w
72”h x 18”d x 36”w
72”h x 18”d x 36”w
Description
Beams (black)
Beams (silver)
Braces (black)
Braces (silver)
Post
Side Panel
Back Panel
Right Door
Left Door
Wood Shelves
Hardware Bag
Handle
Left Hinge
Right Hinge
Qty.
7
3
4
6
8
2
2
1
1
5
3
1
2
2
Part Number
RMBE3503BLK
RMBE3503SLVR
RMBE1703BLK
RMBE1703SLVR
RUPT3602
RMSP1534
RMBK1734
SVRMDRR1734
SVRMDRL1734
RPB21836
NB3
305-TMR
H100-L
H100-R
Part Size
36”
36”
18”
18”
36”
15” x 34”
17” x 34”
17” x 34”
17” x 34’
18” x 36”
N/A
N/A
N/A
N/A
General Instructions
General Instructions
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used
on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block
of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and
fully engaged.
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel
free to contact our Edsal manufacturing facility at, [phone] and request customer service. We can
also be reached on the internet at the following email address : [e-mail].
To obtain replacement parts, please provide the following information :
- Model # - Part # & Description - Location Purchased - Date Purchased
Consumer Products Division
Edsal Manufacturing Company
4400 South Packers Avenue
Chicago, IL 60609 www.edsal.com

Assembly Instructions for MR3600
Assembly Instructions for MR3600
Assembly Instructions for MR3600
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
Assemble the back panels using the nuts and bolt sup-
plied. Insert one (1) silver beam to the back top slots of
the posts, and place the back panels between the post
and over the beam. Continue by adding two (2) silver
beams even with the braces of the bottom levels. Add
one (1) black beam to the front of the unit placing the
bottom rivet into the top slots of the post. Assemble the
top post to the bottom post. One (1) rivet from each beam
and brace must be placed in the top hole of the bottom
post, and the bottom hole of the top post (see figure E).
Tap all beams and braces to properly seat the rivets.
Add wood shelves to the levels built. Align rivets from the
hinges of the doors to the sixth and twentieth post slots from
the bottom, and fasten the doors to the post. Install the
handle holder to the hole of the right door using the correct
orientation (see figure F). Install handle (in the vertical posi-
tion) through the holder. Place the nylon washer to the
back side of the handle followed by the nut, metal washer,
cam, and top washer. Fasten with the screw provided (see
figure F). Push the button and turn counter clockwise to
lock door. Add the final levels using the black beams and
braces. Add the final two (2) wood shelves to the unit.
Step
2
Step Step
4
Figure D
Figure E Wood shelves
RT. door
LT. door
Handle
hole
Hinges of door
fasten to post
slots six (6)
& twenty (20)
from bottom.
Figure F
Take one (1) silver brace, two (2) post, and one (1) side
panel. With the slot holes of the post pointing down, In-
sert the bottom rivet of the brace with the shelf ledge up
into the top slots of the post. Place the side panel be-
tween the post and over the brace (see figure A). Take
one (1) silver brace, skip one (1) hole from the bottom,
and insert rivets into slots of post (see figure B & C).
Count upward to the 13th, and 14th slots of the posts, and
insert rivets of the third silver brace. Making sure the
side panel rests evenly in-between the post (see figure B).
Step
1
Figure C
Note:
Post are
directional.
The slot
must point
down.
Post Slot Points Down
Figure B
Skip One (1) Slot
Top
Post
Tap Lightly Slot
Down
Bottom
Post
3 Note :
Final levels
use all black
beams & braces.
Silver
Braces
Repeat the process of step one to create the opposite
end of the unit. Next take two (2) black beams and in-
sert the rivets even with the rivets of the bottom, and sec-
ond level braces. Tap down on the bottom and second
level beams and braces to properly seat the rivets (see
figure D). DO NOT TAP DOWN THE TOP BRACES AT
THIS TIME.
Note: 2nd
brace slots
13 & 14
Skip One
(1) Slot
Shelf Ledge Up
Figure A
Silver Brace
Shelf ledge
faces inward
Side Panel
Ledge faces
inward
Post
Slot Points
Down
Slot Points
Down
Black
Beams
(Front)
Note: 2nd
beam slots
13 & 14
Note:
DO NOT TAP DOWN
TOP BRACES AT
THIS TIME !
Tap lightly at this
point to properly
seat the rivets
Silver
Beams
(Back)
Black
Beam
(Front)
Back
Panels
Holder Orientation
Top
Bottom
Top of
Door
Handle
(In vertical Position)
Holder
Nylon
Washer
Metal
Washer
Nut
Cam
Top
Washer
Screw &
Washer